PEERLESS SmartMount SP850-UNL Leitfaden

Installation and Assembly:

Pull-out Swivel Wall Mount with Universal Adapter Bracket for

32" - 58" Flat Panel Screens

Models: SP850-UNL, SP850-UNLP, SP850-UNL-S, SP850-UNLP-S

3215 W. North Ave. • Melrose Park, IL 60160 • (800) 865-2112 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com

Maximum Load Capacity: 150 lb (68 kg)

2 of 22 ISSUED: 4-03-07 SHEET #: 202-9177-5 02-15-10

Table of Contents

Parts List............................................................................................................................................................................. 3,4

Installation to Wood Stud Wall................................................................................................................................................5

Installation to Solid Concrete and Cinder Block .....................................................................................................................6

Installing Adapter Brackets.....................................................................................................................................................8

Mounting and Removing Flat Panel Screen........................................................................................................................ 10

Note: Read entire instruction sheet before you start installation and assembly.

Tools Needed for Assembly

• stud ﬁnder ("edge to edge" stud ﬁnder is recommended) • 3/8" socket wrench (3/8" extended driver is

recommended) • phillips screwdriver • drill • 1/4" bit for concrete and cinder block wall • 5/32" bit for wood stud

wall • level • 6 mm allen wrench (if attaching to PLP models)

• Do not begin to install your Peerless product until you have read and understood the instructions and warnings

contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US

customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact

your local distributor.

• This product should only be installed by someone of good mechanical aptitude, has experience with basic building

construction, and fully understands these instructions.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardware and components.

• Never exceed the Maximum Load Capacity. See page one.

• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of

an "edge to edge" stud ﬁnder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tighten screws ﬁrmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding

power.

• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal

injury.

• This product was designed to be installed on the following wall construction only;

WALL CONSTRUCTION HARDWARE REQUIRED

• Wood Stud Included

•Wood Beam Included

•Solid Concrete Included

•Cinder Block Included

• Metal Stud Do not attach except with Peerless Metal Stud Accessory Kit

- ACC415;

• Brick Contact Qualiﬁed Professional

• Other or unsure? Contact Qualiﬁed Professional

WARNING

3 of 22 ISSUED: 4-03-07 SHEET #: 202-9177-5 02-15-10

EDC

BB CC

EE M

Before you begin, make sure all parts shown are included with your product.

Parts may appear slightly different than illustrated.

SP850-UNL SP850-UNLP SP850-UNL-S SP850-UNLP-S

Description Qty. Part # Part# Part # Part#

wall mount assembly 1 201-0385 201-0386 201-0383 201-0384

Blocking tab 1 200-1871 200-1871 200-4871 200-4871

C.219 ID x .5 OD x .125H spacer 1 540-1032 540-1032 540-1032 540-1032

D#14 x 2.5" hex head wood screw 4 5S1-015-C03 5S1-015-C03 5S1-015-C03 5S1-015-C03

EAlligator® anchor 4 590-0097 590-0097 590-0097 590-0097

F18" polyester mesh sleeve 2 600-1014 600-1014 600-1014 600-1014

Gcable tie 4 560-9711 560-9711 560-9711 560-9711

KM10 x 15 mm socket head screw 4 520-9262 520-9262 520-9262 520-9262

L.198 x .313 x .437H retaining spacer 4 590-5005 590-5005 590-5005 590-5005

M4 mm security allen wrench 1 560-1146 n/a 560-1146 n/a

M5 x 10 mm socket pin screw 5 520-1063 520-1233 520-1063 520-1233

BB M4 x 12 mm socket pin screw 4 510-1079 504-9013 510-1079 504-9013

CC M4 x 20 mm serrated head socket pin screw 4 510-1061 504-9020 510-1061 504-9020

DD M5 x 40 mm serrated head socket pin screw 1 510-1001 520-1199 510-1001 520-1199

EE adapter plate 1 201-1110 201-1110 201-4110 201-4110

FF shallow adapter bracket 2 200-0756 200-0754 200-0757 200-0755

GG deep adapter bracket 2 200-0752 200-0750 200-0753 200-0751

HH 4 mm allen wrench 1 n/a 560-0072 n/a 560-0072

Parts List

4 of 22 ISSUED: 4-03-07 SHEET #: 202-9177-5 02-15-10

M5 x 25 mm (4)

520-1122

M4 x 12 mm (6)

510-1079

M4 x 25 mm (4)

510-1082

M5 x 12 mm (4)

520-1064 M6 x 12 mm (4)

520-1050

M6 x 25 mm (4)

520-1211

I.D. 5.6 mm (4)

540-1057

multi-washer (6)

580-1036

I.D. 8.7 mm (4)

540-1059

Security Adapter Bracket Fasteners

M6 x 20 mm (4)

520-9554

M6 x 30 mm (4)

520-1067

M8 x 15 mm (6)

520-1068

M8 x 40 mm (4)

520-1152

M8 x 25 mm (4)

520-1101

M6 x 20 mm (4)

520-9402

M6 x 30 mm (4)

510-9109

multi-washer (6)

580-1036

M8 x 16 mm (6)

520-9257

M8 x 40 mm (4)

520-1136

M4 x 12 mm (6)

504-9013

Phillips Adapter Bracket Fasteners

M4 x 25 mm (4)

504-1015

M5 x 12 mm (4)

520-1027

M5 x 25 mm (4)

520-9543

M6 x 12 mm (4)

520-1128

M6 x 25 mm (4)

520-1208

I.D. 5.6 mm (4)

540-1057

M8 x 25 mm (4)

520-1031

I.D. 8.7 mm (4)

540-1059

INSTALLATION TAB

Snap installation tab off of wall mount assembly (A).

5 of 22 ISSUED: 4-03-07 SHEET #: 202-9177-5 02-15-10

Installation to Wood Stud Wall

CL = stud centerline

Using a stud ﬁnder, locate the edges of the wood studs used in mounting this product. Use of an edge-to-edge stud

ﬁnder is highly recommended. Based on its edges and using a level, draw a vertical line down the center of each

stud. Mark a point (point 1) on the right stud centerline where upper right slot will be located. Using a level, mark a

point (point 2) on the left stud centerline level with point 1 as shown in ﬁgure 2.1. Drill 5/32" diameter holes 2-1/2"

deep through studs at the two points. Loosely fasten wall mount assembly (A) to wall using two #14 x 2-1/2" wood

screws (D) as shown in ﬁgure 2.2. Level, hold, and then tighten screws.

Mark two more points for bottom slots on the right and left stud centerlines. Drill 5/32" diameter holes 2-1/2" deep

through studs at the two points. Using two #14 x 2-1/2" wood screws, fasten bottom of wall mount assembly to wall

as shown in ﬁgure 2.3.

Skip to step 3 on page 7.

ﬁg 2.1

POINT 1

POINT 2

ﬁg 2.3

• Installer must verify that the supporting surface will safely support the combined load of the equipment and all

attached hardware and components.

• Tighten wood screws so that wall plate is ﬁrmly attached, but do not overtighten. Overtightening can damage the

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud ﬁnder

is highly recommended.

• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Install-

ers are responsible to provide hardware for other types of mounting situations.

WARNING

ﬁg 2.2

6 of 22 ISSUED: 4-03-07 SHEET #: 202-9177-5 02-15-10

Position wall mount assembly (A) at desired position

on wall. Use wall mount assembly, making sure that

it is level, as a template to mark holes. Drill four 1/4"

(6 mm) dia. holes to a minimum depth of 2-1/2"

(64 mm). Concrete must be 2000 psi density mini-

mum. Insert anchors (E) in holes ﬂush with wall as

shown in ﬁgure 2.4. Place wall mount assembly over

anchors and secure with #14 x 2-1/2" wood screws

(D) as shown in ﬁgure 2.5. Make sure wall plate is

level and tighten all fasteners.

Installation to Solid Concrete and Cinder Block Wall

• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete

thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid

part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 speciﬁca-

tions. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to

avoid breaking out the back of the hole when entering a void or cavity.

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard-

ware and components.

WARNING

ﬁg 2.5

SOLID CONCRETE

CINDER BLOCK

CUTAWAY VIEW

INCORRECT

concrete

plaster/

drywall

CORRECT

concrete

plaster/

drywall

• Tighten screws so that wall plate is ﬁrmly attached,

but do not overtighten. Overtightening can damage

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Always attach concrete anchors directly to load-

bearing concrete.

• Never attach concrete anchors to concrete covered

with plaster, drywall, or other ﬁnishing material.

If mounting to concrete surfaces covered with a

ﬁnishing surface is unavoidable, the ﬁnishing surface

must be counterbored as shown below. Be sure

concrete anchors do not pull away from concrete

when tightening screws. If plaster/drywall is thicker

than 5/8", custom fasteners must be supplied by

installer (not evaluated by UL).

WARNING

concrete

wall

ﬁg 2.4

Drill holes and insert anchors

Place wall plate (A) over anchors and secure

with screws (D)

Tighten all fasteners

7 of 22 ISSUED: 4-03-07 SHEET #: 202-9177-5 02-15-10

Installing Adapter Plate

Thread two M10 x 15 mm screws (K), leaving .25" exposed thread, into top holes on back of adapter plate (EE).

Hook adapter plate (EE) to mounting plate and attach using two bottom M10 x 15 mm screws (K) as shown in ﬁg-

ures 4.1 and 4.2. Tighten screws using 6 mm allen wrench (not included).

ﬁg. 4.1

MOUNTING PLATE

(NOTE: MOUNTING PLATE

SHOWN WITHOUT FULL

WALL MOUNT ASSEMBLY

FOR CLARITY)

MOUNTING PLATE

ﬁg. 4.2

INSTALLATION TAB

SLIDING ARM

Place installation tab over sliding arms of wall mount assembly (A) to lock them in place.

8 of 22 ISSUED: 4-03-07 SHEET #: 202-9177-5 02-15-10

Note: "X" dimensions should be equal.

• Tighten screws so adapter brackets are ﬁrmly attached. Do not tighten with excessive force. Overtightening can

cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become

detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.

• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly

secured, damage may occur to screen or product may fail.

WARNING

Installing Adapter Brackets

To prevent scratching the screen, set a cloth on a ﬂat, level surface that will support the weight of the screen. Place

screen face side down. Refer to screen manufacturers instructions or customer service, for removing any knobs,

base, cover, or screw(s) on the back of the screen to prepare mounting. These need to be removed to allow the

adapter brackets to be attached. Select the small, medium, large or extra large screws from the bafﬂed fastener

pack then attach adapter brackets (FF or GG) to screen following ﬁgure 5.1 or 5.2.

NOTE: Top and bottom mounting holes on screen must be used for attaching brackets. Verify that all holes are

properly aligned, and then tighten screws using a phillips screwdriver.

CENTER

BRACKETS

VERTICALLY

ON BACK OF

SCREEN

NOTE: For ﬂat back screens proceed to step 5-1. For bump-out or recessed back screen skip to step 5-2.

MEDIUM HOLE FOR M5 SCREWS

SMALL HOLE FOR M4 SCREWS

LARGE HOLE FOR M6 SCREWS

Notes:

• The number of fasteners used will vary, depending upon

the type of screen.

• Multi-washers and spacers may not be used, depending

upon the type of screen.

• Use the corresponding hole in the multi-washer that

matches your screw size as shown.

MULTI-WASHER

9 of 22 ISSUED: 4-03-07 SHEET #: 202-9177-5 02-15-10

Begin with the shortest length screw, hand thread through multi-washer and adapter bracket into screen as shown

below. Screw must make at least three full turns into the mounting hole and ﬁt snug into place. Do not over tighten.

If screw cannot make three full turns into the screen, select a longer length screw from the bafﬂed fastener pack.

Repeat for remaining mounting holes, level brackets and tighten screws.

NOTE: Spacers may not be used, depending upon the type of screen.

Begin with longer length screw, hand thread through multi-washer, adapter bracket and spacer in that order into

screen as shown below. Screw must make at least three full turns into the mounting hole and ﬁt snug into place.

Do not over tighten. If screw cannot make three full turns into the screen, select a longer length screw from the

bafﬂed fastener pack. Repeat for remaining mounting holes, level brackets and tighten screws.

For Flat Back Screen

For Bump-out or Recessed Back Screen

5-1

5-2

If you have any questions, please call Peerless customer care at 1-800-865-2112.

SCREEN

MULTI-WASHER

SCREW

ADAPTER

BRACKET

(BB OR CC)

ﬁg. 5.2

SPACER

ﬁg. 5.1

ADAPTER

BRACKET

(BB OR CC)

SCREEN

MULTI-WASHER

SCREW

10 of 22 ISSUED: 4-03-07 SHEET #: 202-9177-5 02-15-10

Hook adapter brackets (FF or GG) onto adapter plate (EE), then slowly swing screen in as shown. Turn screws

clockwise at least six times to prevent screen from being removed as shown in detail 1.

Note: Tighten using 4 mm security allen wrench (M), or 4 mm allen wrench (HH).

Screen can be adjusted horizontally if desired.

NOTE: To lock the screen down, tighten screws to adapter plate as shown in detail 1.

To remove screen from mount, loosen screws, swing screen away from mount, and lift screen off of mount.

Mounting and Removing Flat Panel Screen

FF or GG

• Always use an assistant or mechanical lifting equipment to safely lift and position the plasma television.

WARNING

Screen can tilt 5° or 10° forward.

NOTE: Screen must be securely attached to mounting plate with all fasteners before adjusting tilt.

To tilt screen 5° forward, lift and pull mounting plate forward until middle notch rests on M6 screw as shown in ﬁgure

7.1. Tighten M6 screw (both sides) and M10 screws (both sides).

To tilt screen 10° forward, lift and pull mounting plate forward until rear notch rests on M6 screw as shown in ﬁgure

7.2. Tighten M6 screw (both sides) and M10 screws (both sides).

NOTE: For security models, tighten M6 screw using security allen wrench (M). For all M10 screws, use 6 mm allen

wrench (not included).

DETAIL 1

SCREWS

ﬁg. 7.1 ﬁg. 7.2

5° tilt

10° tilt

M6 SCREW

MOUNTING

PLATE

M6 SCREW

MOUNTING

PLATE

ADAPTER

BRACKET

SCREEN

M10 SCREW

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere PEERLESS Rack & Stand Handbücher

PEERLESS

PEERLESS LCT-202 Leitfaden

PEERLESS

PEERLESS PED 410 Leitfaden

PEERLESS

PEERLESS SGLS01 Leitfaden

PEERLESS

PEERLESS CMJ450 Leitfaden

PEERLESS

PEERLESS SmartMount SA750P Leitfaden

PEERLESS

PEERLESS SMARTMOUNT SCS221 Leitfaden

PEERLESS

PEERLESS HDS-S Leitfaden

PEERLESS

PEERLESS Solid-Point PLCM UN1 Leitfaden

PEERLESS

PEERLESS A100IWBMOUNT Leitfaden

PEERLESS

PEERLESS Paramount PP730 and assembly Leitfaden

PEERLESS

PEERLESS DS495 Leitfaden

PEERLESS

PEERLESS LMAM1940 Leitfaden

PEERLESS

PEERLESS LCT Series Leitfaden

PEERLESS

PEERLESS SUT632P Leitfaden

PEERLESS

PEERLESS Paramount PT650 Leitfaden

PEERLESS

PEERLESS SmartMount D-FPF-320 Leitfaden

PEERLESS

PEERLESS PLCM 3 Leitfaden

PEERLESS

PEERLESS HL4UN-002 Leitfaden

PEERLESS

PEERLESS PM 47 Leitfaden

PEERLESS

PEERLESS LCC 18-C Leitfaden

PEERLESS

PEERLESS LDM233K Leitfaden

PEERLESS

PEERLESS PARAMOUNT PA740 Bedienungsanleitung

PEERLESS

PEERLESS SAL730P Leitfaden

PEERLESS

PEERLESS Smartmount SA752P Leitfaden

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung