PEERLESS Paramount PT650 Leitfaden

3215 W. North Ave. • Melrose Park, IL 60160 • (800) 865-2112 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com

ISSUED:10-31-07 SHEET#:202-9243-1

Installation and Assembly:

Paramount™ Universal Tilt Wall Mounts for 32" - 50" LCD

and Flat Panel Plasma Screens

This product is UL Listed. It

must be installed by a qualified

professional installer.

Features:

• Universal mount fits screens with mounting hole patterns up to 29.06" W x 17.67" H

• Screen held only 2.5" from wall for a discreet installation

• Open wall plate design allows for greater wall access and an array of cable management options

• Universal tilt brackets easily hook onto the wall plate for fast installation

• Adjustable up to 15° of forward tilt and up to -5° backward tilt for optimal viewing angle

• One-touchtiltforeffortlessadjustment

• Pre-tensioned universal tilt bracket allows for tilt angle adjustment in one easy motion.

• Easy locking handle locks the screen position into place without the use of tools

• Optional IncreLok feature offers fixed tilts at -5°, 0°, 5°, 10°, 15° increments

• Includes Sorted-For-You™ fastener packs for installation to wood studs, concrete, and cinder block

• Optionalhorizontaladjustmentofupto8"(dependingonscreenmodel)forperfectscreenplacement

Maximum UL Load Capacity: 175 lb (79kg)

Model: PT650

2 of 24 ISSUED:10-31-07 SHEET#:202-9243-1

Visit Peerless website at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870

Tools Needed for Assembly

•studfinder("edgetoedge"studfinderisrecommended)

•phillipsscrewdriver

•drill

•1/4" bit for concrete and cinder block wall

•1/2" bit for metal stud wall

•5/32" bit for wood stud wall

•level

Table of Contents

Parts List..............................................................................................................................................................................3

Installation to Double Wood Stud Wall..................................................................................................................................4

Installation to Solid Concrete or Cinder Block .......................................................................................................................5

InstallingTiltBrackets...........................................................................................................................................................6

Installing Flat Panel Screen to Wall Plate.............................................................................................................................8

Forcustomercarecall(800)865-2112 or (708) 865-8870.

NOTE: Read entire instruction sheet before you start installation and assembly.

• DonotbegintoinstallyourPeerlessproductuntilyouhavereadandunderstoodtheinstructionsand warnings

containedinthisInstallationSheet.Ifyouhaveanyquestionsregardinganyoftheinstructions or warnings, please

callPeerlesscustomercareat 1-800-865-2112.

• This product should only be installed by someone of good mechanical aptitude, has experience with basic building

construction, and fully understands these instructions.

• Makesurethatthesupportingsurfacewillsafelysupportthecombinedloadoftheequipmentandallattachedhard-

wareandcomponents.

• NeverexceedtheMaximumULLoad Capacity.Seepageone.

• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an

"edgetoedge"studfinderishighlyrecommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tightenscrewsfirmly, but do notovertighten.Overtighteningcandamagetheitems, greatly reducing theirholding

power.

• Thisproduct was designed and intendedtobe mounted to the following supportingsurfaces checked below with the

hardware included in this product as specified in the installation sheet.To mount this product to an alternative support-

ing surface, contact Peerless customer care at 1 800 865-2112.

• This product was designed to be installed on the following wall construction only;

WALLCONSTRUCTION ADDITIONALHARDWAREREQUIRED

WoodStud None

WoodBeam None

SolidConcrete None

CinderBlock None

MetalStud Do not attach except with Peerless accessory kit for metal studs;

Contact Customer Service for Peerless accessory kit for metal studs.

Brick ContactCustomer Service

Otherorunsure? ContactCustomer Service

WARNING

Accessories

• ACC415 - Metal Stud Fastener Kit (Metal stud

installationisnot evaluated by UL)

•PS200- Paramount™A/V Component Shelf

3 of 24 ISSUED:10-31-07 SHEET#:202-9243-1

Visit Peerless website at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870

BB CC

DD EE

Adapter Bracket Fasteners

M4 x 12 mm (6)

504-9013

M4 x 25 mm (4)

504-1015

M5 x 12 mm (4)

520-1027

M5 x 25 mm (4)

520-9543

M6 x 12 mm (4)

520-1128

M6 x 25 mm (4)

520-1208

M8 x 16 mm (6)

520-9257

M8 x 40 mm (4)

520-1136

M8 x 25 mm (4)

520-1031

M6 x 30 mm (4)

510-9109

M6 x 20 mm (4)

520-9402 multi-washer(6)

580-1036

I.D. .34" (8.7 mm) (4)

540-1059

I.D..22' (5.6 mm) (4)

540-1057

Partsmay appear slightly different than illustrated.

Qty. Part #

AA wall plate 1 201-P1288

BB 1 201-P1469

CC 1 201-P1471

DD 4 5S1-015-C03

EE 4 590-0097alligator®anchor

#14 x 2.5" wood screw

Before you begin,make sure all parts shown are included

with your product.

Parts List

Description

right tilt bracket

left tilt bracket

4 of 24 ISSUED:10-31-07 SHEET#:202-9243-1

Visit Peerless website at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870

Installation to Double Wood Stud Wall

1Wall plate (AA) can be mounted to two studs that are 16" apart. Use a stud finder to locate the edges of the studs.

Useofanedge-to-edgestudfinderishighlyrecommended.Basedon their edges, draw a vertical line down each

stud’s center. Place wall plate on wall as a template. The top mounting slots should be 4.6" (117) above the desired

screen center as shown in figure 1.1. Level plate, and mark the center of the four mounting holes. Make sure that the

mounting holes are on the stud centerlines. Drill four 5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep. Make sure that

the wall plate is level, secure it using four #14 x 2.5" wood screws (DD) as shown in figure 1.2.

NOTE: Wall plate may be mounted up to 4" (102 mm) off center as shown in figure 1.1.

Skip to step 2 on page 6.

• Installermust verify that the supporting surface will safelysupport the combined load of the equipment andallattached

hardwareandcomponents.

• Tightenwood screws so that wall plateisfirmly attached, but do not overtighten.Overtighteningcan damage the

screws,greatly reducing theirholding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is

highlyrecommended.

• Hardwareprovided is for attachment ofmount through standard thickness drywallor plaster into wood studs.Installers

areresponsible to providehardware for othertypes of mounting situations.

WARNING

fig. 1.1

fig. 1.2

(102 mm)

STUD

4.6"

(117mm)

DD AA

CS = center of screen

5 of 24 ISSUED:10-31-07 SHEET#:202-9243-1

Visit Peerless website at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870

Installation to Solid Concrete or Cinder Block

1Make sure that wall plate (AA) is level, use it as a

template to mark four mountingholes. The top mounting

holeshouldbe4.6" (117) abovethe desired screen center

as shown in figure 1.1 on page 4. Drill four 1/4" (6 mm)

dia. holes to a minimum depth of 2.5" (64 mm). Insert

anchors (EE) in holes flush with wall as shown (right).

Place wall plate over anchors and secure with #14 x 2.5"

screws(DD). Level, then tighten all fasteners.

• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete

thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid

part of the block, generally 1" minimum from the side of the block. Cinder block must meetASTM C-90 specifica-

tions. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to

avoid breaking out the back of the hole when entering a void or cavity.

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Makesurethatthe supporting surface will safely support the combined load of the equipment and all attached hard-

wareand components.

WARNING

concrete

surface

Drill holes and insert anchors (EE).

Place plate (AA)over anchors (EE) and secure with screws (DD).

Tighten all fasteners.

CUTAWAYVIEW

INCORRECT

CORRECT

wall

plate

plaster/

drywall

concrete

wall plate concrete

plaster/

drywall

• Always attach concrete anchors directly to load-

bearingconcrete.

• Neverattach concreteanchors to concretecovered

withplaster, drywall, or other finishing material.If

mountingto concrete surfacescoveredwith a finishing

surfaceis unavoidable, thefinishingsurface must be

counterboredas shown below. Be sureconcrete

anchorsdo not pull away fromconcrete when tighten-

ing screws. If plaster/drywall is thicker than 5/8",

custom fasteners must be supplied by installer.

WARNING

• Tighten screws so that wall plate is firmly attached,

butdo notovertighten. Overtighteningcandamage

screws,greatly reducing theirholding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

WARNING

solid concrete

cinder block

6 of 24 ISSUED:10-31-07 SHEET#:202-9243-1

Visit Peerless website at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870

Attaching Tilt Brackets to Screen using Baffled Fastener Pack

To prevent scratching the screen, set a cloth on a flat, level surface that will support the weight of the screen. Place

screenfacesidedown.Refertoscreenmanufacturers instructionsorcustomerservice, forremovinganyknobs, base,

coverorscrew(s)on thebackofthe screentopreparemounting. Theseneedtoberemovedtoallow theadapter

brackets to be attached. Select the small, medium, large or extra large screws from the baffled fastener pack then

attach tilt brackets to screen following figure 2.1 or 2.2.

NOTE: Be sure to attach tilt brackets with handles facing outward as shown below.

NOTE:Top and bottommountingholes must be usedfor attachingbrackets.Middle holes should alsobe used where

thefasteners and screens allow. Verify that all holesareproperly aligned, and then tighten screwsusinga phillips

screwdriver.

NOTES:

• Always use multi-washers when attaching tilt brackets

(BB and CC) to your screen when using small, medium or

largescrews. No multi-washer isrequired for extra large

(M8)screws.

• Usethe corresponding hole in themulti-washerthat

matches your screw size as shown.

• Tightenscrews so adapter brackets are firmlyattached. Do not tighten with excessiveforce. Overtightening can

cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become

detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.

• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly

secured, damage may occur to screen or product may fail.

WARNING

MULTI-WASHER

MEDIUMHOLEFORM5SCREWS

LARGEHOLEFORM6SCREWS

SMALLHOLEFORM4SCREWS

CENTERBRACKETSVERTICALLYONBACK

OFSCREEN

HANDLESFACEOUT

Note: "X"dimensions should be equal.

NOTE: For flat back screens proceed to step 2-1. For bump-out or recessed back screen skip to step 2-2.

7 of 24 ISSUED:10-31-07 SHEET#:202-9243-1

Visit Peerless website at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870

Refer to Screen Compatibility Chart to determine the proper fastener to use. Visit www.peerlessmounts.com/2

for a full screen compatibility chart for this mount.

Begin with the shortest length screw, hand thread through multi-washer and adapter bracket into screen as shown

below. Screw must make at least three full turns into the mounting hole and fit snug into place. Do not over tighten.

If screw cannot make three full turns into the screen, select a longer length screw from the baffled fastener pack.

Repeatfor remaining mounting holes, level brackets and tighten screws.

NOTE: Spacersmay not be used, depending upon the type of screen.

Refer to Screen Compatibility Chart to determine the proper fastener to use. Visit www.peerlessmounts.com/2

for a full screen compatibility chart for this mount.

Beginwithlongerlengthscrew, hand thread through multi-washer, adapter bracket and spacerin that order into

screen as shown below. Screw must make at least three full turns into the mounting hole and fit snug into place. Do

not over tighten. If screw cannot make three full turns into the screen, select a longer length screw from the baffled

fastenerpack.Repeat for remaining mounting holes, level brackets and tighten screws.

For Flat Back Screen

For Bump-out or Recessed Back Screen

SCREEN

MULTI-WASHER

SCREW

ADAPTER

BRACKET

(BB or CC)

fig. 2.2

SPACER

ADAPTER

BRACKET

(BB or CC)

SCREEN fig. 2.1

MULTI-WASHER

SCREW

2-1

2-2

Ifyou have any questions,please call Peerless customer careat 1-800-865-2112.

8 of 24 ISSUED:10-31-07 SHEET#:202-9243-1

Visit Peerless website at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870

Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.

For preset tilt angles use Increlok™ and for custom tilt

angleuseratchet handle.

INCRELOK™: The screen can be locked into a

pre-set tilt position of -5°, 0°, 5°, 10°or 15°. Use

locator hole to find tilt position hole and tilt screen to

align holes. Tighten IncreLok™ tilt locking screws on

both tilt brackets to lock tilt as shown in detail 2.

Ratchet Handle: Loosen ratchet handle (refer to step

3 for tension adjustment of handle). Push or pull from

top or bottom of screen to adjust tilt as shown in figure

4.1. The tilt can be adjusted to a maximum of 15°

forwardor 5°backward.

Tension Adjustment of Ratchet Handle:Adjust

tension in tilt brackets (BB & CC) by rotating ratchet

handle. NOTE:If obstructionprevents ratchet handle

fromrotating, pull handle out while turning will allow

handleto reposition without tightening. Release and

turn handle to tighten or loosen.

Mounting Screen: Ratchet handle must be in the up

ordown position or interference will occur while

hooking tilt brackets to wall plate (AA). Slowly hook tilt

brackets (BB & CC) onto wall plate (AA) and swing

screen down as shown in fig. 3.1. Tilt bracket hooks

must fully engage wall plate as shown in detail 1.

Using a phillips screw driver, turn safety screws on tilt

brackets (BB & CC) clockwise till screw tip securely

contacts wall plate as shown in cross section.

Screen Adjustment: Screen can be adjusted

horizontally by loosening safety screws on tilt

brackets (BB & CC) three full turns with a phillips

screw driver.Adjust screen as shown infigure 3.2.

Tighten safety screws on tilt brackets till screw tip

securely contacts wall plate as shown in cross

section.

Removing Screen: To remove screen from mount,

loosen safety screws, swing screen away from mount,

and lift screen off of mount.

Mounting and Removing Flat Panel Screen

DETAIL 2

fig 4.1

IncreLok™

TILTLOCKING

SCREW LOCATOR

HOLE

RATCHET

HANDLE

TILT

POSITION

HOLES

fig 3.2

Adjusting the Tilt Angle of the Flat

Panel Screen

fig 3.1

RATCHET

HANDLE

SAFETY

SCREW

DETAIL 1

BB &

CROSS SECTION

BB &

• Always use an assistant or mechanical lifting equipment

to safely lift and position the flat panel screen.

• Donot tighten screwswith excessive force. Overtightening

can cause damage to mount. Tighten screws to 40 in. • lb

(4.5N.M.) maximum torque.

• Becareful not to pinch fingerswhenpushing screen from

the bottom.

WARNING

3215 W. North Ave. • Melrose Park, IL 60160 • (800) 865-2112 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com

ISSUED:10-31-07 SHEET#:202-9243-1

Este producto está inscripto en la

Lista UL. Debe ser instalado por

un instalador profesional

cualificado.

Modelos: PT650

Máxima capacidad de carga UL:175 lb (79kg)

Instalación y montaje:

Soporte universal de pared plano con capacidad de

inclinación para pantallas LCD y pantallas planas de

plasma de 32" a 50"

Características:

• El soporte universal sostiene pantallas con configuraciones de montaje de hasta 29.06" W x 17.67" H

• Sostiene el televisor a sólo 2.5" de la pared para proporcionar una instalación discreta

• El diseño abierto de la placa de pared permite más acceso a la pared y proporciona una amplia variedad de opciones

parael manejo de cables

• Lossoportes inclinables universales se enganchan con facilidad a la placa de pared para proporcionar una instalación

rápida

• Inclinación ajustable hacia delante de hasta 15° y hacia atrás de hasta -5° para ver el televisor desde un ángulo óptimo

• Inclinación de un solo toque para permitir el ajuste sin esfuerzo

• Elsoporte inclinable universal preapretado permite ajustar el ángulo de inclinación con un solo movimiento sencillo

• La palanca de fijación fácil fija la posición de la pantalla con seguridad sin la necesidad de usar herramientas

• Lafunciónopcional IncreLok™ ofrece ángulos de inclinación predeterminados en incrementos de -5°, 0°, 5°, 10° y 15°

• Incluyeel paquetesde sujetadoresSorted-For-You™ parainstalacionesen montantes de madera, concreto y bloques de

hormigónde escorias

• Ajuste horizontal opcional de hasta 8" (dependiendo del modelo de la pantalla) para la colocación perfecta de la pantalla

10 of 24 ISSUED:10-31-07 SHEET#:202-9243-1

Español

Visite el sitio Web de Peerless en www.peerlessmounts.com Para el Servicio al cliente llame al 1-800-729-0307 ó 708-865-8870

Accessories

•Repisa ParamountTM - PCS200 para

componentes de A/V

•Juego de accesorios de piezas para la fijación en

montantes de metal - ACC415 (El montante de

metal no ha sido evaluado por UL)

Herramientas necesarias para el montaje

•localizador de montantes (se recomienda usar el de “borde a borde”)

•destornillador phillips

•taladro

•broca de 1/4" para pared de concreto y de bloques de hormigón de

escorias

•broca de 1/2" para pared con montantes de metal

•broca de 5/32" para pared con montantes de metal o madera

•nivel

Tabla de contenido

Lista de piezas ...................................................................................................................................................................11

Instalaciónen una pared con montantes de madera dobles................................................................................................12

Instalación en una pared de concreto macizo o de bloques de hormigón de escorias ........................................................13

Instalaciónde lossoportes adaptadores .............................................................................................................................14

Instalación y desinstalación de la pantalla plana ................................................................................................................16

• No comience a instalar su producto de Peerless hasta haber leído y entendido las instrucciones y las advertencias

contenidas en la Hoja de Instalación. Si tiene alguna pregunta acerca de cualquiera de las instrucciones o las

advertencias,por favor, llamea Servicioal Cliente dePeerless al1-800-865-2112.

• Esteproducto sólo debe ser instalado por unapersona que tenga una aptitud mecánica, quetengaexperiencia en

construcción básica de edificios y que entienda estas instrucciones en su totalidad.

• Asegúrese de que la superficie de apoyo sostendrá, con seguridad, la carga combinada del equipo y todos los

fijadoresy componentes.

• Nuncasobrepase lacapacidad máximadesoportarcarga aceptadapor Underwriters Laboratories.(Vea la página9).

• Si va a instalar el producto en una pared con montantes de madera, asegúrese de que los tornillos de montaje estén

anclados en el centro de los montantes. Se recomienda utilizar un localizador de montantes de “borde a borde”.

• Siempre cuente con la ayuda de un asistente o utilice un equipo mecánico de izar para levantar y colocar el equipo

conmás seguridad.

• Apriete los tornillos con firmeza, pero no en exceso.Apretarlos en exceso puede dañar los artículos y puede

disminuirsignificativamente su fuerzade fijación.

• Este producto fue diseñado con la intención de que se instale en las superficies de apoyo marcadas abajo con los

accesorios de instalación incluidos en este producto como se especifica en la hoja de instalación. Para instalar este

productoen otra superficie deapoyo, llame a Servicioal Cliente de Peerless al1-800-865-2112.

• Esteproducto fue diseñado para ser instalado en paredescon la siguiente construcción solamente:

CONSTRUCCIÓNDELAPARED ACCESORIOS ADICIONALES NECESARIOS

Montantedemadera Ninguno

Vigade madera Ninguno

Concretomacizo Ninguno

Bloquede hormigón deescorias Ninguno

Montantede metal No lo instale excepto con el juego de accesorios de Peerless para

montantes de metal.

Llame a Servicio al Cliente para pedir el juego de accesorios de

Peerless para montantes de metal.

Ladrillo Comuníquesecon Servicioal Cliente.

¿Otrasuperficie o no está seguro? Comuníquesecon Servicioal Cliente.

ADVERTENCIA

Nota: Lea la hoja de instrucciones completa antes de comenzar la instalación y el ensamblaje.

Inhaltsverzeichnis

Sprachen:

Andere PEERLESS Rack & Stand Handbücher

PEERLESS

PEERLESS LDM233K Leitfaden

PEERLESS

PEERLESS IMC 18 Leitfaden

PEERLESS

PEERLESS DS-VL-H018 Leitfaden

PEERLESS

PEERLESS CMJ450 Leitfaden

PEERLESS

PEERLESS RTPLA 50 Leitfaden

PEERLESS

PEERLESS SAL730P Leitfaden

PEERLESS

PEERLESS SGLS01 Leitfaden

PEERLESS

PEERLESS PARAMOUNT PA730 Bedienungsanleitung

PEERLESS

PEERLESS SmartMount D-FPF-320 Leitfaden

PEERLESS

PEERLESS DST940 Leitfaden

PEERLESS

PEERLESS SPK 811W Bedienungsanleitung

PEERLESS

PEERLESS SmartMount SP740P Leitfaden

PEERLESS

PEERLESS Solid-Point PLB 1 Leitfaden

PEERLESS

PEERLESS ACC-V800X Leitfaden

PEERLESS

PEERLESS Perfect Mount PMF2X2 Bedienungsanleitung

PEERLESS

PEERLESS MOD-FPSKIT150 Bedienungsanleitung

PEERLESS

PEERLESS PLAV 70 Leitfaden

PEERLESS

PEERLESS ESA746PU Leitfaden

PEERLESS

PEERLESS Solid-Point PLCM 1 CP Leitfaden

PEERLESS

PEERLESS PARAMOUNT PRA2X2 Bedienungsanleitung

PEERLESS

PEERLESS Smartmount SWS310/BK Leitfaden

PEERLESS

PEERLESS DS-VW760 and assembly Leitfaden

PEERLESS

PEERLESS WBK100-W Leitfaden

PEERLESS

PEERLESS HCW201 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung