PEERLESS LDS 1920U Leitfaden
ISSUED: 11-05-04 SHEET #: 090-9102-4 09-27-10
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
1 of 5
DESCRIPTION QTY. LDS 1920U LDS 1920U-S LDS 2527U LDS 2527U-S LDS 32U LDS 32U-S
A1 tray 19" - 20" 1 090-1243 090-4243
A2 tray 25" - 27" 090-1244 090-4244
A3 tray 32" 090-1245 090-4245
B#10 x 3/4 particle board screw 8 500-9006 500-9006 500-9006 500-9006 500-9006 500-9006
Cpenta-pin tool 1 520-9249 520-9249 520-9249 520-9249 520-9249 520-9249
DM5 x .8 x 10 mm phillips screw 2 520-9250 520-9250 520-9250 520-9250 520-9250 520-9250
EPeerless cover plate 2 590-1046 590-4046 590-1046 590-4046 590-1046 590-4046
F1/4-20 x 1 3/4 bolt 1 520-9204 520-9204 520-9204 520-9204 520-9204 520-9204
Gspacer 3 540-9455 540-9455 540-9455 540-9455 540-9455 540-9455
HM5 x .8 x 10 mm penta-pin™screw 2 505-9010 500-2001 505-9010 500-2001 505-9010 500-2001
I1/4-20 3 prong T-nut 1 530-9301 530-9301 530-9301 530-9301 530-9301 530-9301
J#1 x 1-1/4 phillips pan wood screw 1 510-9157 510-9157 510-9157 510-9157 510-9157 510-9157
Kswivel base 1 090-0246 090-0247 090-0246 090-0247 090-0246 090-0247
Ladhesive bumper strip 1 570-1029 570-1029 570-1029 570-1029 570-1029 570-1029
Installation and Assembly - Universal Desktop Mount Models:
LDS 1920U, LDS 1920U-S,
LDS 2527U, LDS 2527U-S,
LDS 32U, LDS 32U-S
IMPORTANT! Read entire instruction sheet before you start installation and assembly.
Parts List
Note: Some parts may appear slightly different than illustrated.
B C E
D
A3
F
I
H
G
Before you start make sure all parts listed are included with your product.
JK
A2A1
L
This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal injury.
ISSUED: 11-05-04 SHEET #: 090-9102-4 09-27-10
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
2 of 5
TurnTVupsidedownanddeterminemounting
locations. For TV’s with a flat front, make sure that
leadingedge of screen is flushwith leading edge of
tray. For TV’s with a curved front, mount screen as
close to the front of leading edge of tray with tray
still being hidden.Attach tray to TV by installing
four screws (B) into TV mounting bosses.
• Donot lift more weight than you can handle. Useadditional manpower or mechanical liftingequipment to safely lift
andattachthetelevision!
WARNING
TOP VIEW
Note: If TV is flush with tray, x= 0.
LEADING EDGE
OF TRAY
LEADING EDGE
OF SCREEN
x
x= leading edge of tray to leading edge of screen
ForflatscreenTVs,peelpaperfromadhesive
bumper strip (L) and place flush to the front lip
on bottom of TV.
For ZenithH32F56, cut 1" strips off each side of
adhesivebumberstrip(L).Peelpaperfrom
longer strip and place flush to the front lip on
bottom of TV as shown in figure 1.Also, peel
paper from the 1" strips and place on front feet
of TV as indicated.
figure 1
BOTTOMOF TV
FRONTLIPOF TV L
1"STRIPS
B
ISSUED: 11-05-04 SHEET #: 090-9102-4 09-27-10
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
3 of 5
Determine position on desktop to secure mount.
SeeNote below. The leading edgeofTVshould
be flush with edge of mounting surface once TV is
installed. Once position is determined, align .281"
diameterholesin swivel base (marked 1-4 below)
with holes in race. Mark holes and drill 1/8" (3
mm) diameter pilot holes 3/4" (19 mm) into
mountingsurface.
There are two methods of installation. Follow steps 2 and 4 for installation using four 3/4" particle board
screws or steps 3 and 5 to use one 1-3/4" bolt.
For mounting to surface using one 1-3/4" bolt,
determine position on desktop to secure mount.
SeeNote below. The leading edge of TV should
be flush with edge of mounting surface once TV is
installed. Mark holes and drill one 5/16" (8 mm)
diameter thru hole and one 1/8" (3 mm) diameter
pilot hole 3/4" (19 mm) into mounting surface.
Note: To figure out where to mount swivel base soTV is
flush with the edge of the mounting surface, use
thefollowingformula:
y = x + 1.25"
Use distance x from step 1 on previous page.
1
2
3
4
EDGE
1/8" (3 MM)
DIA. PILOT
HOLE
5/16" (8 MM)
DIA. THRU
HOLE
1
EDGE
Note: To figure out where to mount swivel base soTV is
flush with the edge of the mounting surface, use
thefollowingformula:
y = x + 1.25"
Use distance x from step 1 on previous page.
y
EDGEOFTRAY
EDGEOFMOUNTINGSURFACE
EDGEOFTRAY
y
EDGEOFMOUNTINGSURFACE
1.25" 1.25"
ISSUED: 11-05-04 SHEET #: 090-9102-4 09-27-10
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
4 of 5
Align holes in race with holes 1 through 4 of swivel
base. Once position is determined, attach swivel
base to surface using four screws (B) into posi-
tions 1 through 4. If swivel restriction is needed,
use one spacer (G) and screw (B) in position 1 and
then refer to step 6. If you would like to prevent the
swivelbase from swiveling atall, install one screw
(J) into back hole #1 instead of screw (B) and
spacer(G).
Align holes in race with holes 1 through 4 of swivel
base. Once position is determined, attach swivel
base to surface using one screw (F) and one T-nut
(I) in center of swivel base and one screw (B) and
one spacer (G) in back hole #1. If swivel restriction
is needed, use one spacer (G) and screw (B) in
position 1 and then refer to step 6. If you would like
toprevent the swivel base from swiveling atall,
install one screw (J) into back hole #1 instead of
screw(B) and spacer (G).
Swivel Restriction
Tray swivel can be stopped entirely (as described in steps 4 and 5) or restricted to either 10, 30, 60, or 90
degrees.To restrict swivel, place two screws (D) with spacers (G) into holes on left and on right at desired
degree.
G
B
F
30° 30°
60°
90°
60°
90°
0°
B
G
D
G
J
I
10° 10°
41
2
3
41
2
3
ISSUED: 11-05-04 SHEET #: 090-9102-4 09-27-10
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
5 of 5
TABS
LIP
Attach tray, with TV mounted onto it, to swivel base by
sliding trays together. The lip of the tray (as shown) will
lock into the slot in swivel base. The slot of the two
tabs in the tray will align with the two holes on the
swivelbase.
To lock trays together, be certain that the hole in the
swivel base is centered within the slot in the tray (see
detail below). Secure on left and right using two penta-
pin screws (H) with tool (C).
DETAIL
©2004PeerlessIndustries,Inc. Allrightsreserved.
PeerlessisaregisteredtrademarkofPeerlessIndustries,Inc.
Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.
SLOT HOLE
H
Finishby snapping two Peerlesscover plates (E)
onto tray as shown.
E
SLOT
HOLES
Dieses Handbuch passt für folgende Modelle
5
Inhaltsverzeichnis
Andere PEERLESS Rack & Stand Handbücher
PEERLESS
PEERLESS DS 35 Leitfaden
PEERLESS
PEERLESS IWB600-WB Leitfaden
PEERLESS
PEERLESS MOD-FPSKIT150 Bedienungsanleitung
PEERLESS
PEERLESS SmartMount SF650 Leitfaden
PEERLESS
PEERLESS SmartMount SA750P Leitfaden
PEERLESS
PEERLESS PM 47 Leitfaden
PEERLESS
PEERLESS COL 510P Leitfaden
PEERLESS
PEERLESS PLC Leitfaden
PEERLESS
PEERLESS ESA746PU Leitfaden
PEERLESS
PEERLESS SUT632P Leitfaden
PEERLESS
PEERLESS IWB600-WB Bedienungsanleitung
PEERLESS
PEERLESS SF630-AB Leitfaden
PEERLESS
PEERLESS PARAMOUNT PT640 and assembly Leitfaden
PEERLESS
PEERLESS Paramount PSP2 Leitfaden
PEERLESS
PEERLESS SF630P-S and assembly Leitfaden
PEERLESS
PEERLESS LCT Series Leitfaden
PEERLESS
PEERLESS HCACC502 Bedienungsanleitung
PEERLESS
PEERLESS MSA-301 Leitfaden
PEERLESS
PEERLESS PTT188743 Series Bedienungsanleitung
PEERLESS
PEERLESS Paramount PS200 Leitfaden
Beliebte Rack & Stand Handbücher anderer Marken
Salamander
Salamander Acadia AC/W/L400/WH Bedienungsanleitung
Fohhn
Fohhn VAT-09 Benutzerhandbuch
ricoo
ricoo FS0522 Bedienungsanleitung
AMSOIL
AMSOIL BMK-22 Kurzanleitung
Kargo Master
Kargo Master 48220 Bedienungsanleitung
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung
