Pepperl+Fuchs VBA-2E-G11-I/U/PT100-F Bedienungsanleitung

Spec 2.1

VBA-2E-G11-I/U/PT100-F

VBA-2E-G11-I/U/PT100-V1

AS-Interface Analog Module

FACTORY AUTOMATION

MANUAL

With regard to the supply of products, the current issue of the following document is ap-

plicable: The General Terms of Delivery for Products and Services of the Electrical Indus-

try, published by the Central Association of the Electrical Industry (Zentralverband

Elektrotechnik und Elektroindustrie (ZVEI) e.V.) in its most recent version as well as the

supplementary clause: "Expanded reservation of proprietorship"

VBA-2E-G11-I/U/PT100-*

1 Introduction................................................................................. 4

2 Declaration of Conformity.......................................................... 5

3 Safety ........................................................................................... 6

3.1 Symbols relevant to safety.................................................................. 6

3.2 Intended Use ........................................................................................ 6

3.3 General Safety Instructions................................................................. 6

4 Product Description ................................................................... 7

4.1 Displays and Controls ......................................................................... 7

4.2 Connections ......................................................................................... 8

4.3 Automatic Detection of the Sensor Type ........................................... 9

4.4 Pt100 temperature sensor................................................................. 10

5 Installation................................................................................. 11

5.1 Storage and transport........................................................................ 11

5.2 Unpacking........................................................................................... 11

5.3 Mounting............................................................................................. 11

5.4 Connecting the AS-Interface............................................................. 11

5.5 Connecting the Sensors.................................................................... 13

6 Commissioning......................................................................... 14

6.1 Assigning an Address to the Module............................................... 14

6.2 Slave Profile........................................................................................ 14

6.3 Parameterization ................................................................................ 14

7 Troubleshooting........................................................................ 16

7.1 Causes and Elimination of Peripheral Faults .................................. 16

7.2 Cause and elimination of a channel fault ........................................ 16

8 Appendix A................................................................................ 17

8.1 Dimensions......................................................................................... 17

8.2 Technical Data .................................................................................... 17

9 Appendix B................................................................................ 20

9.1 Analog Input Module Measurement Ranges ................................... 20

9.2 Delay Times ........................................................................................ 21

2014-02

VBA-2E-G11-I/U/PT100-*

Introduction

1Introduction

Congratulations

You have chosen a device manufactured by Pepperl+Fuchs. Pepperl+Fuchs develops,

produces and distributes electronic sensors and interface modules for the market of

automation technology on a worldwide scale.

Before you install this device and put it into operation, please read the operating instructions

thoroughly. The instructions and notes contained in this operating manual will guide you step-

by-step through the installation and commissioning procedures to ensure trouble-free use of

this product. By doing so, you:

■

guarantee safe operation of the device

■

can utilize the entire range of device functions

■

avoid faulty operation and associated errors

■

reduce costs from downtimes and incidental repairs

■

increase the effectiveness and operating efficiency of your plant.

Store this operating manual somewhere safe in order to have it available for future work on the

device.

After opening the packaging, please ensure that the device is intact and that the package is

complete.

Symbols used

The following symbols are used in this manual:

Handling instructions

You will find handling instructions beside this symbol

Contact

If you have any questions about the device, its functions, or accessories, please contact us at:

Pepperl+Fuchs GmbH

Lilienthalstraße 200

68307 Mannheim

Telephone: +49 621 776-4411

Fax: +49 621 776-274411

E-Mail: fa-info@pepperl-fuchs.com

Note!

This symbol draws your attention to important information.

VBA-2E-G11-I/U/PT100-*

Declaration of Conformity

2014-02

2 Declaration of Conformity

All products were developed and manufactured under observance of the applicable European

standards and guidelines.

The product manufacturer, Pepperl+Fuchs GmbH, 68307 Mannheim, has a certified quality

assurance system that conforms to ISO 9001.

Note!

A Declaration of Conformity can be requested from the manufacturer.

ISO9001

2014-02

VBA-2E-G11-I/U/PT100-*

Safety

3Safety

3.1 Symbols relevant to safety

3.2 Intended Use

The VBA-2E-G11-I/U/PT100-* is an analog module for connecting 0 V ... 10 V or 0/4 mA ... 20

mA measurement sensors and Pt100 sensors to the AS-Interface network. Measured values

are converted and data transmitted asynchronously as defined by AS-Interface profile 7.3. The

measured values are converted internally at a resolution of 16 bits. The analog module features

two analog inputs which can be current input, voltage input, or resistance therm ometer input.

The measurement sensors are powered either by the AS-Interface or by the auxiliary power

source.

Read through these instructions thoroughly. Familiarize yourself with the device before

installing, mounting, or operating.

Always operate the device as described in these instructions to ensure that the device and

connected systems function correctly. The protection of operating personnel and plant is only

guaranteed if the device is operated in accordance with its intended use.

3.3 General Safety Instructions

Only instructed specialist staff may operate the device in accordance with the operating

manual.

User modification and or repair are dangerous and will void the warranty and exclude the

manufacturer from any liability. If serious faults occur, stop using the device. Secure the device

against inadvertent operation. In the event of repairs, return the device to your local

Pepperl+Fuchs representative or sales office.

The connection of the device and maintenance work when live may only be carried out by a

qualified electrical specialist.

The operating company bears responsibility for observing locally applicable safety regulations.

Store the not used device in the original packaging. This offers the device optimal protection

against impact and moisture.

Ensure that the ambient conditions comply with regulations.

Danger!

This symbol indicates an imminent danger.

Non-observance will result in personal injury or death.

Warning!

This symbol indicates a possible fault or danger.

Non-observance may cause personal injury or serious property damage.

Caution!

This symbol indicates a possible fault.

Non-observance could interrupt devices and any connected facilities or systems, or result in

their complete failure.

Note!

Disposal

Electronic waste is hazardous waste. When disposing of the equipment, observe the current

statutory requirements in the respective country of use, as well as local regulations.

VBA-2E-G11-I/U/PT100-*

Product Description

2014-02

4ProductDescription

4.1 Displays and Controls

Figure 4.1 Display and control elements

The VBA-2E-G11-I/U/PT100-* analog module is equipped with the following displays and

controls:

LED Indicator

Switch

In order to reach the switch, remove the blind plug

AS-i/FAULT LED Status indication; multicolor LED

Green: normal mode

Red: communication error

Flashing yellow/red: address 0

Flashing green/red: peripheral fault

PT1 LED

PT2 LED

Status of input signal; yellow LED

Off: not active

On: signal within measurement range

Flashing: signal outside measurement range

I1 LED

I2 LED

U1 LED

U2 LED

AUX LED Ext. auxiliary power source (U

AUX

); dual LED (green/red)

Green: voltage OK

Red: voltage reversed

INT/EXT LED Status indication, input supply; green LED

Green: internal input supply

Off: external input supply

INT/EXT switch

Set to INT: sensors powered via the AS-Interface (max. 140 mA)

Set to EXT: sensors powered via an auxiliary power source (max. 600 mA)

VBA-2E-G11-I/U/PT100

AUX

AS-i

FAU LT

INT

EXT

2014-02

VBA-2E-G11-I/U/PT100-*

Product Description

4.2 Connections

VBA-2E-G11-I/U/PT100-F

Figure 4.2 Connections VBA-2E-G11-I/U/PT100-F

The VBA-2E-G11-I/U/PT100-F analog module is equipped with the following connections:

VBA-2E-G11-I/U/PT100-V1

Figure 4.3 Connections VBA-2E-G11-I/U/PT100-V1

The VBA-2E-G11-I/U/PT100-V1 analog module is equipped with the following connections:

Pt100 inputs

: functional ground

M12 round plug connector

Current inputs

Voltage inputs

Addressing socket Low voltage switch socket, 1.3 mm

Pt100 inputs

: functional ground

M12 round plug connector

Current inputs

Voltage inputs

AS-Interface/U

AUX

1: AS-Interface +

2: AUX -

3: AS-Interface -

4: AUX +

M12 round plug connector

VBA-2E-G11-I/U/PT100

AUX

AS-i

FAU LT

INT

EXT

VBA-2E-G11-I/U/PT100

AUX

AS-i

FAU LT

INT

EXT

VBA-2E-G11-I/U/PT100-*

Product Description

2014-02

4.3 Automatic Detection of the Sensor Type

The VBA-2E-G11-I/U/PT100-* analog input module automatically detects which sensor type is

connected. The types of sensors that can be connected are: 0 V ... 10 V measurement

sensors, 0/4 mA ... 20 mA-measurement sensors, or Pt100 temperature sensors. The sensor

type is automatically detected once switched on. Once the module has detected the sensor

type, the corresponding module configuration is activated.

All input LEDs are illuminated during the first few seconds after switching on. During this time,

the module evaluates the connected sensor type on the basis of various measured values. The

signal values that ensure unambiguous detection of the type of sensor connected are:

■

Voltage: 1 V ... 11.5 V

■

Current: 1 mA ... 23 mA

■

Pt100: -219 °C ... 884 °C

If the module cannot clearly establish which sensor type is connected, the last detected sensor

type is provisionally activated. For example, the module may not detect which sensor type is

connected if the signal values are not within the specified thresholds or if two different sensor

types are simultaneously applied to one channel.

A specific sensor type is finally activated when the signal values measured are within the

specified thresholds.

Note!

Switching Off the Second Channel

Figure 4.4 Input PT2 bridge

Two bridges are plugged in at the PT100 input PT2 by default; these bridges are designed to

switch off channel 2. Remove the bridges to use channels 1 and 2.

The bridges must be plugged in and disconnected only when the module is de-energized!

Note!

The Pt100 Input Is an Exception:

The Pt100 sensor type is only activated if a Pt100 temperature sensor is connected to the

PT100 inputs before switching on. The Pt100 sensor type cannot be activated during operation

or activated provisionally.

Note!

If you connect two different sensor types to one channel simultaneously, fault-free operation is

not guaranteed. The module will not be damaged by this.

2014-02

VBA-2E-G11-I/U/PT100-*

Product Description

4.4 Pt100 temperature sensor

Pt100 temperature sensors are platinum resistance thermometers complying with standard

IEC 751 / DIN EN 60751. In this standard, various values of the temperature sensor are

defined. The nominal resistance of the Pt100 is 100 , measured at 0 °C. Furthermore, as well

as other values, the mean temperature coefficient of 0°C to 100 °C is also defined. The mean

temperature coefficient defines the mean change in resistance relative to the nominal

resistance. The analog module calculates the corresponding temperature based on the

measured resistance of the temperature sensor.

Figure 4.5 Curve Pt100

100

150

200

250

300

350

400

Resistance [Ω]

Temperature [°C]

Pt100

Curve Resistance Thermometer Pt100

0 100 200 300 400 500 600 700 800 900

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Pepperl+Fuchs Steuereinheit Handbücher

Pepperl+Fuchs

Pepperl+Fuchs WCS-ECG410 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs VLX-F231-B6 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs ICE1-8IOL-S2-G60L-V1D Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs VAA-2E1A-CB10-SJ/E2J-FL Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs IC-KP2-1HB6-V15B Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs VAA-2E-KE1-S Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs VBA-4E4A-G20-ZEJ/M48L-P12 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs SC4-2 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs VBA-4E2A1A-KE3-ZEL/E2L/SEL Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs PSU-IDM160-BD-1D-J1-N0 Series Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs VBA-2A-KE5-IL/UL Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs WCS DG310 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs VBA-2E-KE5-IJL Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs ICE11-8IOL-G60L-V1D Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs PS1000-A6-24.10.R Handbuch

Pepperl+Fuchs

Pepperl+Fuchs HD2-DM-A Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs WCS-EIG410 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs VBA-4E-KE5-IL Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs VAA-2E2A-KE1P-S/E2 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs VAA-2E2A-KE1-S/E2 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs VBA-4E3A-G20-ZEL/M1L-P6 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs 5500 Series Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs IC-KP2-2HB17-2V1D Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs VU121 Referenzhandbuch

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung