Philips FC8705 Bedienungsanleitung
FC8715, FC8710,
FC8705, FC8700
FC8715
FC8710
FC8705
5
6
4
3
2
1
7
8
15
13
12
14
11
9 10
17
18
2021
19
16
1
English 6
Deutsch 17
Español 29
Français 41
Italiano 53
Nederlands 64
Português 75
Svenska 86
Русский 97
Қазақша 109
English
Introduction
Introduction
Congratulations on your purchase and welcome to Philips! To fully benefit from the support that
Philips offers, register your product at www.philips.com/welcome.
General description
1 Top cover
2 Handle of dust container lid
3 Dust container lid
4 Filter
5 Dust container
6 Fan
7 Bumper
8 Docking station sensor
9 Start/stop button (to start or stop the robot)
10 Display
11 Front wheel
12 Side brush shafts
13 Drop-off sensors
14 Wheels
15 Suction opening
16 Side brushes
17 Battery holder
18 Remote control (FC8715, FC8710, FC8705)
19 Small plug
20 Adapter
21 Docking station
Display and remote control
Display (Fig. 2):
1 Warning indicator
2 Start/stop indicator
3 Dust container full indicator
Remote control (Fig. 3):
1 Navigation buttons and start/stop
2 Docking button
3 Cleaning time button
4 Cleaning mode buttons
How your robot works
What your robot cleans
This robot is equipped with features that make it a suitable cleaner to help you clean the floors in your
home.
6English
The robot is especially suitable for cleaning hard floors, such as wooden, tiled or linoleum floors. It
may experience problems cleaning soft floors, such as carpet or rugs. If you use the robot on a carpet
or rug, please stay close by the first time to see if the robot can deal with this type of floor.
Because the robot uses infrared sensors to navigate, it may run into difficulties on very dark and shiny
floors. If you use the robot on such surfaces, please stay close by the first time to see if the robot can
deal with such a dark and shiny floor.
How your robot cleans
Cleaning system
The robot has a 2-stage cleaning system to clean your floors efficiently.
-The two side brushes help the robot clean in corners and along walls. They also help to remove dirt
from the floor and move it towards the suction opening (Fig. 4).
-The suction power of the robot picks up loose dirt and transports it through the suction opening
into the dust container (Fig. 5).
Cleaning patterns
In its auto cleaning mode, the robot uses an automatic sequence of cleaning patterns to clean each
area of the room optimally. The cleaning patterns it uses are:
1 Z-pattern or zigzag pattern (Fig. 6)
2 Random pattern (Fig. 7)
3 Wall-following pattern (Fig. 8)
4 Spot-cleaning pattern (Fig. 9)
In its auto cleaning mode, the robot uses these patterns in a fixed sequence: z-pattern, random
pattern, wall-following pattern, and spot-cleaning pattern.
When the robot has completed this sequence of patterns, it starts moving in Z-pattern again. The
robot continues to use this sequence of patterns to clean the room until the rechargeable battery runs
low, or until it is switched off manually.
Note (FC8715, FC8710, FC8705): You can also select each mode individually by pressing the
appropriate button on the remote control. For more details, see chapter 'Using your robot', section
'Cleaning modes'.
How your robot avoids height differences
The robot has three drop-off sensors in its bottom. It uses these drop-off sensors to detect and avoid
height differences such as staircases.
Note: It is normal for the robot to move slightly over the edge of a height difference, as its front drop-
off sensor is located behind the bumper.
Caution: In some cases, the drop-off sensors may not detect a staircase or other height difference
in time. Therefore monitor the robot carefully the first few times you use it, and when you operate it
near a staircase or another height difference. It is important that you clean the drop-off sensors
regularly to ensure the robot continues to detect height differences properly (see chapter ' Cleaning
and maintenance' for instructions).
7
English
Before first use
Before first use
1Unpack the side brushes and place the robot upside down on a table or on the floor.
2Push the side brushes onto the shafts on the bottom of the robot (Fig. 10).
Note: Make sure you attach the side brushes properly. Press them onto the shaft until you hear
them lock into position with a click.
Removing the protection tag from the remote control
This only applies to FC8715, FC8710, FC8705.
The remote control works on a CR2025 coin-shaped battery. This battery is protected with a
protection tag that has to be removed before use.
1Pull the battery protection tag out of the battery compartment of the remote control (Fig. 11).
Now the remote control is ready for use.
Preparing for use
Installing the docking station
1Insert the small plug of the adapter into the socket on the docking station (1) and insert the adapter
into the wall socket (2) (Fig. 12).
2Place the docking station on a horizontal, level floor against a wall.
Note: Make sure that there are no obstacles or height differences 80 cm in front, 30 cm to the right
and 100 cm to the left of the docking station (Fig. 13).
Important note: deep sleep mode
In deep sleep mode, the robot does not respond at all when you press a button. To reactivate the
robot when it is in deep sleep mode:
1Press the start/stop button on the robot for 1 second to bring the robot from deep sleep mode to
standby mode.
2Press the start/stop button on the robot or on the remote control briefly to start the robot.
3If the robot does not start cleaning, place it on the plugged-in docking station to recharge its
rechargeable battery.
The robot enters deep sleep mode when you press the start/stop button for 3 seconds. It may also
enter the deep sleep mode when its battery is empty. The battery may, for instance, run empty if the
robot is unable to find its docking station.
Charging
-When charging for the first time and when the rechargeable battery of the robot is empty, the
charging time is 4 hours.
-When the rechargeable battery is fully charged, it has a runtime of about 130 minutes.
-Your robot can only be charged on the docking station.
8English
Charging on the docking station
1Place the robot on the plugged-in docking station (Fig. 14).
2The robot starts charging automatically and the start/stop indicator starts flashing green slowly
(Fig. 15).
3When the rechargeable battery is fully charged, the start/stop indicator lights up solid green (Fig.
16).
Charging automatically during use
1When the robot has finished cleaning or when only 15% of the battery power remains, it
automatically searches for the docking station to recharge. When the robot searches for the
docking station, the start/stop indicator flashes green slowly (Fig. 17).
2When the battery runs low, the start/stop button turns solid red and the robot searches for the
docking station.
3When the rechargeable battery is fully charged, the start/stop indicator lights up solid green.
Note: The robot only searches for the docking station automatically when it started cleaning from the
docking station.
Clap response
The clap response is enabled when the robot enters sleep mode in the following situations:
-when it stops cleaning due to an error
-when it cannot find its docking station in 20 minutes
If you do not see the robot, you can locate it by clapping your hands once. The robot will respond by
beeping and by lighting up all icons on its display.
Using your robot
Preparing the room for a cleaning run
Before you start the robot on its cleaning run, make sure that you remove all loose and fragile objects
from the floor (Fig. 18).
Also remove all cables, wires and cords from the floor.
Functions of the start/stop button
The start/stop button has the following functions:
How you press start/stop button How robot responds
Press start/stop button for 1 second Robot switches from sleep mode to standby
Press start/stop button briefly Robot starts or stops cleaning
Press start/stop button for 3 seconds Switches robot on or off.
Signals and their meaning
The robot has a display with three indicators: a warning indicator, a start/stop indicator and the dust
container full indicator. The table below explains the meaning of the signals.
9
English
Signal Meaning
The start/stop indicator lights up solid green. The robot is ready to clean.
The start/stop indicator flashes green slowly. The robot is charging.
The robot searches for the docking station
because the battery is low.
The start/stop indicator lights up solid red. The rechargeable battery of the robot runs low
and the robot searches for its docking station.
The dust container full indicator lights up solid
red.
The dust container is full.
The warning indicator lights up solid red but the
start/stop indicator is green.
The robot was lifted while it was cleaning.
The warning indicator is solid red. The bumper of the robot is stuck.
The dust container is not present or not placed
properly.
The color of the floor is too dark.
The warning indicator flashes red. A wheel or side brush is stuck.
Charging error or battery is not present.
Starting and stopping
1Press the start/stop button.
-You can press the start/stop button on the robot (Fig. 19).
-FC8715, FC8710, FC8705: You can also press the start/stop button on the remote control (Fig.
20).
2The start/stop indicator lights up solid green and the robot starts cleaning (Fig. 22).
3The robot cleans in the auto-cleaning mode until its battery runs low. In the auto-cleaning mode, it
follows repeated sequences of Z-pattern, random, wall-following and spot-cleaning patterns (Fig.
21).
FC8715, FC8710, FC8705:
Note: To select an individual mode, press one of the mode buttons on the remote control. See
section 'Cleaning mode selection' for more details.
4When the battery runs low, the start/stop indicator turns solid red and the robot searches for the
docking station to recharge (Fig. 17).
5You can also press the start/stop button to interrupt or stop the cleaning run. If you press the
start/stop button again and there is still enough energy in the rechargeable battery, the robot
continues cleaning in the auto-cleaning mode.
6FC8715, FC8710, FC8705: To make the robot return to the docking station before the rechargeable
battery runs low, press the docking button on the remote control (Fig. 23).
The start/stop indicator starts flashing green slowly and the robot searches for the docking station
to recharge (Fig. 24).
FC8715, FC8710, FC8705: If there is still enough energy in the rechargeable battery, you can press
the docking button on the remote control to make the robot return to the docking station. If the
10 English
Dieses Handbuch passt für folgende Modelle
8
Inhaltsverzeichnis
Sprachen:
Andere Philips Staubsauger Handbücher
Philips
Philips 4000 series Bedienungsanleitung
Philips
Philips FC8700/01 Bedienungsanleitung
Philips
Philips FC8749 Bedienungsanleitung
Philips
Philips FC9170/01 Bedienungsanleitung
Philips
Philips FC9524 Handbuch
Philips
Philips HR 8368 Bedienungsanleitung
Philips
Philips FC8635 Bedienungsanleitung
Philips
Philips FC6094 Bedienungsanleitung
Philips
Philips FC6149 Bedienungsanleitung
Philips
Philips FC8276/01 Bedienungsanleitung
Philips
Philips Essence 5000 Series Bedienungsanleitung
Philips
Philips Vision HR8731/02 Bedienungsanleitung
Philips
Philips FC6409/61 Bedienungsanleitung
Philips
Philips FC9110/01 Bedienungsanleitung
Philips
Philips FC8920 Bedienungsanleitung
Philips
Philips Mobilo HR 8501 Bedienungsanleitung
Philips
Philips Marathon FC9219 - FC9200 Bedienungsanleitung
Philips
Philips SilentStar FC9306 Bedienungsanleitung
Philips
Philips XW7110 Bedienungsanleitung
Philips
Philips City Line Venice FC8424/02 Bedienungsanleitung
Beliebte Staubsauger Handbücher anderer Marken
Bissell
Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung
Panasonic
Panasonic MC-YL637S147-AE Bedienungsanleitung
NEFF
NEFF N17XH10 0 Series Bedienungsanleitung
LG
LG A9 Series Bedienungsanleitung
Oreck
Oreck Cordless Captura BK51700 Series Bedienungsanleitung
Kogan
Kogan KAVACROBVWA Bedienungsanleitung
