Philips FC8822 Bedienungsanleitung
FC8822, FC8812
FC8822
Wheels stuck
ݓઁሂTopcover or dust container not placed properly
רۆࠋࠦӧ٦ݾBumper stuck
ߓԎሑᇆሂRobot liftedup from oor
՚ֽϴุఓᇊୃስײᆋ༏ӧచColour ofoor too dark
ֽϴဂ೨ขτBattery notinserted properly / Charging error (switchis o)
ԁሑݾԍմ༆IJܵၜܵтij
5
6
4
3
2
1
7
8
9
12
11
10
15
14
13
17
19
18
16
20
22
21
23
25
24
26
1
English 6
简体中文 19
English
Introduction
Congratulations on your purchase and welcome to Philips! To fully benefit from the support that
Philips offers, register your product at www.philips.com/welcome.
General description
1 Handle of dust container lid
2 Dust container lid
3 Filter
4 Dust container
5 Top cover
6 Error codes table
7 Fan
8 Bumper
9 Docking station sensor
10 On/off button
11 Front wheel
12 Side brush shafts
13 Drop-off sensors
14 Wheels
15 Suction opening
16 TriActive XL nozzle
17 Side brushes
18 Fixation blocks for dry wipes
19 Dry wipe holder
20 Dry wipes
21 Battery holder
22 Remote control
23 Invisible wall (FC8822)
24 Docking station
25 Adapter
26 Small plug
Display and remote control
Display of robot
1 Spiral mode indicator
2 Wall-following mode indicator
3 Zigzag pattern mode indicator
4 Random mode indicator
5 Charging indicator and cleaning time indicator (see 'Using the cleaning time buttons')
6 Docking icon
7 Fan speed indicator
8 Dustbin full indicator
9 Sound sensor
10 Mode selection button
11 Start/stop button
12 Fan speed button
Remote control
1 Navigation buttons and start/stop (Fig. 3)
6English
2 Cleaning time buttons
3 Cleaning mode buttons
4 Fan speed buttons
5 Docking button
Control panel of docking station
1 Display with time, day and programming indications (Fig. 4)
2 Adjusting and setting buttons
How your robot works
What your robot cleans
This robot is equipped with features that make it a suitable cleaner to help you clean the floors in your
home.
The robot is especially suitable for cleaning hard floors, such as wooden, tiled or linoleum floors. It
may experience problems cleaning soft floors, such as carpet or rugs. If you use the robot on a carpet
or rug, please stay close by the first time to see if the robot can deal with this type of floor. The robot
also needs supervision when you use it on very dark or shiny hard floors.
How your robot cleans
Cleaning system
The robot has a 3-stage cleaning system to clean your floors efficiently.
1 The two side brushes help the robot clean in corners and along walls. They also help to remove dirt
from the floor and move it towards the suction opening (Fig. 5).
2 The suction power of the robot picks up loose dirt and transports it through the suction opening
into the dust container.
3 The robot comes with a dry wipe holder that allows you to clean your hard floor even more
thoroughly with dry wipes.
Cleaning patterns
In its auto cleaning mode, the robot uses a fixed and automatic sequence of cleaning patterns to
clean each area of the room optimally. It uses a Z-pattern (zigzag pattern), random pattern, wall-
following pattern and spiral pattern successively (Fig. 6). It continues to move in this sequence of
patterns to clean the room until the rechargeable battery runs low, or until it is switched off manually.
If the robot detects a particularly dirty area during its cleaning run, it switches to spiral mode and
switches to turbo fan speed to ensure thorough dirt removal.
Note: You can also select each mode individually by pressing the appropriate button on the remote
control (see 'Cleaning mode selection') or on the robot. The manually selected modes are only active
for a couple of minutes. After that, the robot switches back to auto-cleaning mode.
How your robot avoids height differences
The robot has three drop-off sensors in its bottom. It uses these drop-off sensors to detect and avoid
height differences such as staircases (Fig. 7).
Note: It is normal for the robot to move slightly over the edge of a height difference, as its front drop-
off sensor is located behind the bumper.
7
English
Caution: In some cases, the drop-off sensors may not detect a staircase or other height difference
in time. Therefore monitor the robot carefully the first few times you use it, and when you operate it
near a staircase or another height difference. It is important that you clean the drop-off sensors
regularly to ensure the robot continues to detect height differences properly (see 'Cleaning and
maintenance') .
Before first use
Mounting the side brushes
1Unpack the side brushes and place the robot upside down on a table or on the floor.
2Push the side brushes onto the shafts on the bottom of the robot (Fig. 8).
Note: Make sure you attach the side brushes properly. Press them onto the shaft until you hear
them lock into position with a click.
Removing the tag from the remote control
The remote control works on a CR2025 coin-shaped battery. This battery is protected with a
protection tag that has to be removed before use.
1Pull the battery protection tag out of the battery compartment of the remote control. Now the
remote control is ready for use (Fig. 9).
Preparing for use
Installing the docking station
1Insert the small plug of the adapter into the socket on the docking station (1) and insert the adapter
into the wall socket (2) (Fig. 10).
-The display of the docking station comes on.
2Place the docking station on a horizontal, level floor against the wall.
Note: Make sure that there are no obstacles or height differences 80 cm in front, 30 cm to the right
and 100 cm to the left of the docking station (Fig. 11).
Tip: To ensure the docking station stays firmly in the selected spot, fasten it to the wall with screws
or with two strips of double-sided tape.
Important note: deep sleep mode
In deep sleep mode, the robot does not respond at all when you press a button. To reactivate the
robot when it is in deep sleep mode:
1Press the start/stop button on the robot for one second to switch the robot from deep sleep mode
to standby mode.
2Press the start/stop button on the robot (Fig. 17) briefly or press the start/stop button on the
remote control to start cleaning.
3If the robot does not start cleaning, place it on the plugged-in docking station to recharge its
rechargeable battery.
8English
The robot enters deep sleep mode when you press the start/stop button for 5 seconds. It may also
enter the deep sleep mode when its battery is empty. The battery may, for instance, run empty if the
robot is unable to find its docking station.
Charging
When charging for the first time and when the rechargeable battery of the robot is empty, the charging
time is four hours.
Your robot can be charged on the docking station, either manually or automatically during use.
Note: When the rechargeable battery is fully charged, your robot can clean for up to 120 minutes
Charging automatically during use
1When the robot has finished cleaning or when only 15% of the battery power remains, it
automatically searches for the docking station to recharge. When the robot searches for the
docking station, the light in the start/stop button turns orange (Fig. 15).
2When the rechargeable battery is fully charged, the start/stop button lights up green continuously.
Charging on the docking station
1Place the robot on the plugged-in docking station (Fig. 12).
2The start/stop button starts flashing green. Because this is the first time you charge the robot, the
display of the robot shows the charging indicator (Fig. 13).
3When the rechargeable battery is fully charged, the start/stop button lights up green continuously
(Fig. 14).
Using your robot
Preparing the room for a cleaning run
Before you start the robot on its cleaning run, make sure that you remove all loose and fragile objects
from the floor. Also remove all cables, wires and cords from the floor.
Functions of the start/stop button
The start/stop button has the following functions (Fig. 16):
How you press start/stop button How robot responds
Press start/stop button for 1 second Robot switches from sleep mode to standby
Press start/stop button briefly Robot starts or stops cleaning
Press start/stop button for 5 seconds Switches robot on or off.
User interface signals and their meaning
The robot has a display and a start/stop button gives light signals. The table below explains the
meaning of the signals.
Signal Description of signal Meaning of signal
The start/stop button is continuously green. The robot is ready to clean.
9
English
Signal Description of signal Meaning of signal
The start/stop button flashes slowly green and the
display on the robot shows a moving blue light
(the charging indicator).
The robot is charging.
The start/stop button is continuously orange. The rechargeable battery is low and
the robot is searching for the docking
station.
The start/stop button is continuously red. The rechargeable battery of the robot
is almost empty.
The start/stop button is continuously red and the
display shows an error code.
Please consult the error code table
below to understand the meaning of
the error code.
Error codes
Error code Possible cause Solution
E1 Wheels stuck Remove robot from the obstacle and press
the starts/stop button to resume cleaning.
E2 Top cover or dust
container not placed
properly
Place the dust container in and the top cover
on the robot properly. The error code
disappears from the display automatically.
E3 Bumper stuck Remove the robot from the obstacle. The
error code disappears from the display
automatically.
E4 Robot lifted from floor Put the robot back on the floor to make the
error code disappear.
E5 Color of floor too dark Place robot on a lighter area of the floor.
Clean the drop-off sensors.
E6 Problem with the
battery
Please contact the Consumer Care Center to
have the problem examined.
Clap response
If you do not see the robot, you can locate it by clapping your hands once. The robot will respond by
beeping and by lighting up all icons on its display.
The clap response is enabled when the robot enters sleep mode in the following situations:
-when it stops cleaning due to an error
-when it is unable to find its docking station within 20 minutes
.
Starting and stopping
1Press the start/stop button on the robot (Fig. 17) or on the remote control (Fig. 18). The start/stop
button is continuously green and the robot starts cleaning.
10 English
Andere Handbücher für FC8822
3
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Philips Staubsauger Handbücher
Philips
Philips FC8454/01 Bedienungsanleitung
Philips
Philips Vision Bedienungsanleitung
Philips
Philips SilentStar FC9306 Bedienungsanleitung
Philips
Philips PowerPro Uno FC6170 Bedienungsanleitung
Philips
Philips HR6062/20 Bedienungsanleitung
Philips
Philips FC8442/01 Bedienungsanleitung
Philips
Philips FC9057/01 Bedienungsanleitung
Philips
Philips FC9160 Bedienungsanleitung
Philips
Philips FC8820 Bedienungsanleitung
Philips
Philips FC8149 Bedienungsanleitung
Philips
Philips MiniVac FC6048/01 Bedienungsanleitung
Philips
Philips FC8822 Bedienungsanleitung
Philips
Philips FC6090 Bedienungsanleitung
Philips
Philips XB9185 Bedienungsanleitung
Philips
Philips FC 9012 Bedienungsanleitung
Philips
Philips FC8740 Bedienungsanleitung
Philips
Philips FC6150 Bedienungsanleitung
Philips
Philips PowerPro Duo FC6162/02 Bedienungsanleitung
Philips
Philips SpeedPro FC6724/01 Bedienungsanleitung
Philips
Philips SmallStar FC8286 Bedienungsanleitung
Beliebte Staubsauger Handbücher anderer Marken
Bissell
Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung
Panasonic
Panasonic MC-YL637S147-AE Bedienungsanleitung
NEFF
NEFF N17XH10 0 Series Bedienungsanleitung
LG
LG A9 Series Bedienungsanleitung
Oreck
Oreck Cordless Captura BK51700 Series Bedienungsanleitung
Kogan
Kogan KAVACROBVWA Bedienungsanleitung
