Philips FC9130/01 Bedienungsanleitung

Specialist II

1234

5678

910 11 12

13 14 15 16

17 18 19 20

ENGLISH 6

DEUTSCH 12

FRANÇAIS 18

NEDERLANDS 24

ESPAÑOL 30

ITALIANO 36

PORTUGUÊS 42

NORSK 48

SVENSKA 54

SUOMI 60

DANSK 66

 72

TÜRKÇE 79

SPECIALIST II

Important

Read these instructions for use carefully before using the appliance and save them for future

reference.

◗Only use Philips s-bag`double-layer paper dustbags.

◗Never suck up water or any other liquid.Never suck up flammable substances and do not

suck up ashes until they are cold.

◗Only allow children to operate the vacuum cleaner under close supervision.

◗Do not point the hose at the eyes or ears nor put it in your mouth when the vacuum

cleaner is switched on and the hose is connected to the vacuum cleaner.

◗When the vacuum cleaner is used to suck up fine dust,the pores of the dustbag may become

clogged,causing the passage of air through the dustbag to become obstructed.As a result,the

dustbag-full indicator will indicate that the dustbag needs to be replaced,even though the

dustbag is not full at all.

◗Never use the appliance without the Motor Protection Filter.This could damage the motor

and shorten the life of the appliance.

Preparing for use

Connecting accessories

Hose

1To connect the hose,push it firmly into the appliance ('click').

2To disconnect the hose,push the buttons on the swivel and pull the hose out of the

appliance (fig.1).

Tube

There are two types of coupling systems.Depending on the type,this appliance is equipped with

one of them.See the systems displayed in the following pictures.

Conical coupling (specific types only)

1Connect the tubes to the handgrip by inserting the narrow section into the wider section

while turning it a little (fig.2).

2To disconnect the tubes from the handgrip,pull while turning a little.

Button coupling (specific types only)

1Connect the tube to the handgrip by pressing the spring-loaded lock button on the handgrip

and inserting the handgrip into the tube.Fit the spring-loaded lock button into the opening in

the tube ('click') (fig.3).

2To disconnect the tube from the handgrip,press the spring-loaded lock button and pull the

handgrip out of the tube.

3Use the same method to connect and disconnect the other accessories.

Telescopic tube (specific types only)

1Adjust the tube to the length you find most comfortable during vacuum cleaning (fig.4).

Tri-Active nozzle

1TheTri-Active nozzle is a multi-purpose nozzle for carpets and hard floors (fig.5).

- The side brushes catch more dust and dirt at the sides of the nozzle and allow you to clean

better along furniture and other obstacles.

ENGLISH6

2Push the rocker switch on top of the nozzle with your foot to make the brush strip come

out of the housing.At the same time the wheel will be lifted to prevent scratching and to

increase manoeuvrability (fig.6).

Carpet setting:

3Push the rocker switch again to make the brush strip disappear into the nozzle housing.The

wheel will be lowered automatically.

◗The opening at the front of the nozzle allows you to effectively suck up larger particles

(fig.7).

Crevice tool,small nozzle and small brush

1Connect the crevice tool (1),the small nozzle (2) or the small brush (3) directly to the

handgrip or to the tube (fig.8).

Accessory holder

1The accessory holder can simply be snapped onto the handgrip (fig.9).

◗There are two ways to store accessories in the accessory holder.

2The crevice tool and small nozzle can be stored in the accessory holder by pushing them

into the holder.To detach them,pull them out of the holder (fig.10).

Please note the way in which the small nozzle must be placed in the accessory holder.

3Instead of the small nozzle,the small brush can be stored in the accessory holder by pushing

it into the holder (fig.11).

Animal brush (specific types only)

While combing your dog or cat with the animal brush, dirt,loose hairs and knots will be removed.

Regular combing will keep the fur healthy.

1Connect the animal brush to the handgrip ('click') (fig.12).

2Place the vacuum cleaner as far away from the dog or cat as possible.Set the suction power

to the lowest setting.

3For optimal results,move the brush through the fur of the cat or dog in one direction.

4You can remove hairs from the animal brush by detaching it from the appliance and vacuum

cleaning it (fig.13).

Active Fragrance Control (specific types only)

The scent granules have been specially developed for use in your Philips vacuum cleaner.Only use

the s-fresh`scent granules from Philips in your vacuum cleaner.

If the vacuum cleaner is equipped withActive Fragrance Control,keep it out of the reach of

children.Don't let children play with the appliance.Store the vacuum cleaner in a locked

cupboard if there are small children in the house.

These granules are not edible.

In case of eye contact,flush immediately with plenty of water.

Filling the cartridge

1Place your thumb and index finger on the sides of the cartridge.Remove the cartridge from

the holder by pressing on the disc (fig.14).

ENGLISH 7

2Remove the cap of the cartridge by pulling while applying pressure on the small pressing

points (fig.15).

3Open the package at the small opening at the top.

4Fill the cartridge with the content of one whole package of scent granules.

5Close the cartridge by putting the cap back onto it ('click').

6Re-insert the cartridge into the holder ('click').It only fits into the holder in one way (fig.16).

◗Replace the granules when the cartridge no longer emits any fragrance.

Setting the amount of fragrance

1You can set the amount of fragrance by turning the cartridge forwards (maximum emission)

and backwards (minimum emission) (fig.17).

2When you store the vacuum cleaner or don't want any fragrance to be emitted,close the

cartridge by turning it backwards until the openings of the cartridge are no longer visible.

Using the appliance

Adjusting suction power

1You can adjust the suction power,while vacuum cleaning,with the slide control on top of the

appliance (fig.18).

2Use maximum suction power for vacuum cleaning very dirty carpets and hard floors.

3Use minimum power for vacuum cleaning curtains,table carpets,etc.

Infrared remote control (specific types only)

1Place the batteries in the battery compartment (fig.19).

Make sure the - and + poles are pointing in the right direction.

◗With the infrared remote control you can set the suction power to one of 5 different

suction power settings.When you switch the appliance on,it will always start running at the

highest suction power setting.

2By pushing the - button,you will reduce the suction power by one setting (fig.20).

3By pushing the + button,you will increase the suction power by one setting (fig.21).

4Push the standby button to temporarily switch the vacuum cleaner off,for instance when you

have to move some furniture (fig.22).

5To continue vacuum cleaning,simply press the - button or the + button.The appliance will

start operating at the previously selected suction power setting again.

Parking the tube

1By inserting the ridge on the nozzle into the parking slot,you can park the tube in a

convenient position (fig.23).

ENGLISH8

Storage

1You can put the appliance in upright position and attach the nozzle to the appliance by

inserting the ridge on the nozzle into the slot (fig.24).

2Always put theTri-Active nozzle in carpet setting when you store it and prevent the side

brushes from becoming bent.

Replacement

The dustbag

1Replace the dustbag as soon as the dustbag-full indicator changes colour (fig.25).

The dustbag is full when the colour of the indicator has changed when the nozzle is not placed

on the floor.

2Switch the appliance off.

3Open the cover by pulling it upwards (fig.26).

Place your fingers at the front of the cover and press with your thumb on the ridge on top of the

cover.

4Lift the dustbag holder out of the appliance (fig.27).

Make sure you hold the dustbag upright when lifting it out of the appliance.

5Remove the full dustbag from the holder by pulling the cardboard tag (fig.28).

When you do this,the dustbag will be automatically sealed.

6Slide the cardboard of the new dustbag into the two grooves of the dustbag holder as far as

possible.Re-insert the dustbag holder into the vacuum cleaner (fig.29).

You cannot close the cover if no dustbag has been inserted.

The mains cord

If the mains cord of the appliance is damaged,it must always be replaced by Philips or a service

centre authorised by Philips,as special tools and/or parts are required.

Cleaning and maintenance of filters

Motor Protection Filter

Every time you empty or replace the dustbag,clean the Permanent Motor Protection Filter.

1Remove the dustbag holder with the dustbag (fig.27).

2Take the Motor Protection Filter holder out of the appliance and clean the filter by shaking it

over a dustbin (fig.30).

3Press the filter holder with the clean filter firmly into place to ensure that it fits properly at

the bottom (fig.31).

4Place the dustbag holder with the dustbag back into the appliance.

Activated Carbon Filter (specific types only)

Instead of with the Motor Protection Filter,some appliances are equipped with anActivated Carbon

Filter.This filter neutralises smells produced by dirt in the dustbag.

1Replace theActivated Carbon Filter every 6 months or when you notice that smell

absorption becomes less effective.

ENGLISH 9

2To replace theActivated Carbon Filter,see the Motor Protection Filter section,above.

Instead of cleaning the filter,you have to insert a new filter.

Motor Outlet Filter

The AFS Micro Filter located in the back of this appliance filters a large part of the smallest particles

from the exhaust air by means of its electrostatically charged fibres.

1Replace theAFS Micro Filter every six months

2Open the filter grille (fig.32).

3Remove the old filter (fig.33).

4Insert the new filter into the appliance.

5Close the filter grille and push the left and right bottom corners until they snap home (fig.

34).

HEPA filter (specific types only)

Instead of with the AFS Micro Filter,this appliance can also be equipped with the special HEPA filter.

The HEPA Filter is able to remove at 99,99% of all particles down to 0.0003 mm in size from the

outlet air.This not only includes normal house dust,but also harmful microscopic vermin such as

house dust mites and their excrements,which are well-known causes of respiratory allergies.

1Replace the HEPA Filter as soon as the pilot light of the filter-full indicator goes on (specific

types only) (fig.35).

The HEPA Filter can be replaced in the same way as the AFS Micro Filter.

Ordering accessories

If you have any difficulties obtaining dustbags,filters or other accessories for this appliance,please

contact the Philips Customer Care Centre in your country or consult the worldwide guarantee

leaflet.

Ordering dustbags

- Philips s-bag`paper dustbags are available under type number FC8021 (883802100000).

- Philips Clinic s-bag`high filtration dustbags are available under type number FC8022

(883802201010).

- Philips Anti-odour s-bag`paper dustbags are available under type number FC8023

(883802301010).

Ordering filters

- AFS Micro Filters are available under type number FC8030 (432200492910).

- HEPA Filters are available under type number FC8031 (432200492920).

- Activated Carbon Filters are available under type number FC8033 (48224802145).

Ordering scent granules

- Replacement kits with 4 packages of scent granules are available under type number FC8025

(883802501010).

Environment

To make recycling possible, the plastics used for this appliance have been coded.

The cardboard packaging has been made of recycled material and is fully recyclable.

Types with an infrared remote control only:remove the batteries when you discard the appliance.

Do not throw the batteries away with the normal household waste,but hand them in at an official

collection point.

ENGLISH10

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Philips Staubsauger Handbücher

Philips

Philips FC8209/01 Bedienungsanleitung

Philips

Philips City Line New York Bedienungsanleitung

Philips

Philips FC8026/01 Bedienungsanleitung

Philips

Philips StudioPower FC9080 SERIES Handbuch

Philips

Philips FC8603 Bedienungsanleitung

Philips

Philips FC8149 Bedienungsanleitung

Philips

Philips FC9218/03 Bedienungsanleitung

Philips

Philips FC6402 Bedienungsanleitung

Philips

Philips FC8586/01 Bedienungsanleitung

Philips

Philips FC8700/01 Bedienungsanleitung

Philips

Philips FC8229/61 Bedienungsanleitung

Philips

Philips MiniVac FC6048/01 Bedienungsanleitung

Philips

Philips FC9110 Bedienungsanleitung

Philips

Philips 2000 series Bedienungsanleitung

Philips

Philips FC8297 Bedienungsanleitung

Philips

Philips FC9713 Montageanleitung

Philips

Philips FC9910/01 Bedienungsanleitung

Philips

Philips Performer Bedienungsanleitung

Philips

Philips FC8700 Handbuch

Philips

Philips HR6060/10 Bedienungsanleitung

Philips

Philips Aqua Plus 8000 Series Bedienungsanleitung

Philips

Philips PowerPro Aqua FC6405 Bedienungsanleitung

Philips

Philips SpeedPro Max Bedienungsanleitung

Philips

Philips FC8919 Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

Exido

Exido 240-114 Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung