Pilz PSSu E S 2AI RTD Bedienungsanleitung
PSSu E S 2AI RTD(-T)
Operating Manual 22017-EN-07
}Decentralised system PSSuniversal I/O
Preface
This document is a translation of the original document.
All rights to this documentation are reserved by Pilz GmbH & Co. KG. Copies may be made
for internal purposes. Suggestions and comments for improving this documentation will be
gratefully received.
Source code from third-party manufacturers or open source software has been used for
some components. The relevant licence information is available on the Internet on the Pilz
homepage.
Pilz®, PIT®, PMI®, PNOZ®, Primo®, PSEN®, PSS®, PVIS®, SafetyBUS p®,
SafetyEYE®, SafetyNET p®, the spirit of safety® are registered and protected trademarks
of Pilz GmbH & Co. KG in some countries.
SD means Secure Digital
Contents
Operating Manual PSSu E S 2AI RTD(-T)
22017-EN-07 3
Section 1 Introduction 5
1.1 Validity of documentation 5
1.1.1 Retaining the documentation 5
1.1.2 Terminology: System environment A and B 5
1.2 Definition of symbols 6
Section 2 Overview 7
2.1 Module structure 7
2.2 Module features 7
2.3 Front view 8
Section 3 Safety 10
3.1 Intended use 10
3.2 Safety regulations 11
3.2.1 Use of qualified personnel 11
3.2.2 Warranty and liability 11
3.2.3 Disposal 11
Section 4 Function description 12
4.1 Block diagram 12
4.2 Module features 12
4.2.1 Integrated protection mechanisms 12
4.2.2 Functions 12
4.3 Configuration 13
4.3.1 Measuring ranges 13
4.3.2 Connection type 14
4.3.3 Range monitoring 14
4.3.4 Offset for the 2-wire measurement 14
4.3.5 Digital filter 15
4.3.6 Scaling 16
4.3.6.1 ADC raw value 17
4.3.6.2 Manufacturer scaling 17
4.3.6.3 User scaling 17
4.3.6.4 Values that fall outside the range limits 18
4.3.7 Data formats 18
4.3.8 Summary and overview 19
4.3.9 PSSu assignment in system environment A 20
4.3.9.1 Status byte 21
4.3.10 PSSu assignment in system environment B 21
Section 5 Installation 22
5.1 General installation guidelines 22
5.1.1 Dimensions 22
5.2 Installing the base module 23
5.3 Inserting and removing an electronic module 24
5.3.1 Inserting an electronic module 25
5.3.2 Removing an electronic module 26
Contents
Operating Manual PSSu E S 2AI RTD(-T)
22017-EN-07 4
5.3.3 Changing an electronic module during operation 26
Section 6 Wiring 27
6.1 General wiring guidelines 27
6.1.1 Mechanical connection of the base modules 27
6.2 Terminal configuration 29
6.3 Connecting the module 31
Section 7 Operation 33
7.1 Messages 33
7.2 Display elements 33
7.2.1 Display elements for module diagnostics 33
7.2.2 Displaying the input status 34
Section 8 Technical Details 35
Section 9 Order reference 39
9.1 Product 39
9.2 Accessories 39
Introduction
Operating Manual PSSu E S 2AI RTD(-T)
22017-EN-07 5
1 Introduction
1.1 Validity of documentation
This documentation is valid for the products PSSu E S 2AI RTD and PSSu E S 2AI RTD-T.
It is valid until new documentation is published.
This operating manual explains the function and operation, describes the installation and
provides guidelines on how to connect the product.
The module PSSu E S 2AI RTD-T is suitable for use where there are increased environ-
mental requirements (see Technical Details).
1.1.1 Retaining the documentation
This documentation is intended for instruction and should be retained for future reference.
1.1.2 Terminology: System environment A and B
The PSSu system can be used in two different system environments. The module's applic-
ation area is described in the chapter "Intended Use" of the manual.
The distinction is made between
}PSSu in system environment A
}PSSu in system environment B
The distinction is based on the application area of the PSSu system.
PSSu in system environment A may be used in the
}Decentralised system PSSu I/O
}Not in the automation system PSS 4000
PSSu in system environment B may be used in the
}Automation system PSS 4000, e.g. with
– Decentralised system PSSu I/O with SafetyNET p
– Control system PSSu PLC
– Control system PSSu multi
Introduction
Operating Manual PSSu E S 2AI RTD(-T)
22017-EN-07 6
1.2 Definition of symbols
Information that is particularly important is identified as follows:
DANGER!
This warning must be heeded! It warns of a hazardous situation that poses
an immediate threat of serious injury and death and indicates preventive
measures that can be taken.
WARNING!
This warning must be heeded! It warns of a hazardous situation that could
lead to serious injury and death and indicates preventive measures that can
be taken.
CAUTION!
This refers to a hazard that can lead to a less serious or minor injury plus
material damage, and also provides information on preventive measures
that can be taken.
NOTICE
This describes a situation in which the product or devices could be dam-
aged and also provides information on preventive measures that can be
taken. It also highlights areas within the text that are of particular import-
ance.
INFORMATION
This gives advice on applications and provides information on special fea-
tures.
Overview
Operating Manual PSSu E S 2AI RTD(-T)
22017-EN-07 7
2 Overview
2.1 Module structure
A module consists of
}Electronic module and
}Base module with
– Screw terminals or
– Cage clamp terminals
The base modules are the carrier units for the electronic modules and are used to connect
the field wiring. The electronic modules are inserted on to the base modules and determine
the module's function.
Details of the base modules that can be used are available in the chapter entitled “Intended
Use”.
2.2 Module features
The product has the following features:
}Analogue ST inputs: 2
}Type of inputs: Resistance thermometer
}Corresponding sensors (configurable):
– Pt100
– Pt200
– Pt500
– Pt1000
– Ni100
– Ni120
– Ni1000
}Resistance measurement (configurable):
– 0 ... 4000 Ohm
}Max. resolution:
– 0.0625 °C
– 0.0625 Ohm
}Open circuit detection
}LEDs for:
– Operating status per input
– Module error
}For standard applications in system environment A and B
}T-type:
PSSu E S 2AI RTD-T: for increased environmental requirements
Overview
Operating Manual PSSu E S 2AI RTD(-T)
22017-EN-07 8
2.3 Front view
PSSu E S
2AI RTD
312490
000000
001
I0 I1
PSSu E S
2AI RTD
11
R0+
12
R0-
13
(C)
14
R1+
15
R1-
16
(C)
21
RL0+
22
RL0-
23
(C)
24
RL1+
25
RL1-
26
(C)
Err
2111
2212
2313
2414
2616
2515
1
3
8
7
4
5
6
12
2
13
A
B
9
11
10
Legend:
}A: Electronic module
}B: Base module
}1: LED for module diagnostics
}2: Labelling strip with:
– Name of electronic module
– Order number
– Serial number
– Hardware version number
– 2D code
Overview
Operating Manual PSSu E S 2AI RTD(-T)
22017-EN-07 9
}3: Labelling strip for the terminal configuration on the base module
}4: Name of electronic module
}5: Connection level 1
}6: Connection level 2
}7: Connection level 3
}8: Connection level 4
}9: Connection level 5
}10: Connection level 6
}11: Square mounting holes (connection levels 1, 2, 3 and 4)
– With screw to loosen/tighten the screw terminal on base modules with screw termin-
als
– With mechanism to operate the cage clamp on base modules with cage clamp ter-
minals
}12: Round connection holes (connection levels 1, 2, 3 and 4) for connecting the signal
lines
}13: Mounting slot for colour marker to label the connection level (connection levels 1, 2,
3 and 4)
Safety
Operating Manual PSSu E S 2AI RTD(-T)
22017-EN-07 10
3 Safety
3.1 Intended use
The module may be used for standard applications in system environment A and B.
The module provides analogue inputs. It may be used as an input module for standard
functions.
The modules PSSu E S 2AI RTD and PSSu E S 2AI RTD-T may be used as a safety com-
ponent in accordance with the Lifts Directive 95/16/EC, EN81-1, EN81-2 and EN115-1.
The programmable safety system should be installed in a protected environment that meets
at least the requirements of pollution degree 2. Example: Protected inside space or control
cabinet with protection class IP54 and corresponding air conditioning.
The module PSSu E S 2AI RTD-T is suitable for use where there are increased environ-
mental requirements (see Technical Details).
Intended use includes making the electrical installation EMC-compliant. Please refer to the
guidelines stated in the "PSSuniversal Installation Manual". The module is designed for use
in an industrial environment. It is not suitable for use in a domestic environment, as this can
lead to interference.
The following is deemed improper use in particular:
}Any component, technical or electrical modification to the module
}Use of the module outside the areas described in this manual
}Any use of the module that is not in accordance with the technical details.
INFORMATION
The module is supported by:
}PSSuniversal Configurator and PSSuniversal Assistant from Version
1.6.0
}PAS4000 from version 1.8.0
– We recommend that you always use the latest version (download
from www.pilz.de).
The PSSu E S 2AI RTD module may be used in conjunction with the following base mod-
ules:
}PSSu BP 1/12 S
}PSSu BP 1/12 C
}PSSu BP-C 1/12 S
}PSSu BP-C 1/12 C
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Pilz Steuereinheit Handbücher
Pilz
Pilz PSS u2 ES 4AO U/I Bedienungsanleitung
Pilz
Pilz PNOZ mc7p Bedienungsanleitung
Pilz
Pilz PIT es Set10u-5ns (AIDA) basic Bedienungsanleitung
Pilz
Pilz PIT m3.3p Bedienungsanleitung
Pilz
Pilz PSEN ma1.4n-51 Bedienungsanleitung
Pilz
Pilz PSSu K F FAU B Bedienungsanleitung
Pilz
Pilz PNOZ mc7p Bedienungsanleitung
Pilz
Pilz PMCprotego S1--2 Bedienungsanleitung
Pilz
Pilz PIT js2 Bedienungsanleitung
Pilz
Pilz PNOZ ms4p Bedienungsanleitung
Pilz
Pilz PNOZ po3.2p Bedienungsanleitung
Pilz
Pilz PNOZ mmc12p Bedienungsanleitung
Pilz
Pilz PNOZ mc2.1p Bedienungsanleitung
Pilz
Pilz PNOZ m EF 2MM Bedienungsanleitung
Pilz
Pilz PNOZmulti PNOZ mmc3p Bedienungsanleitung
Pilz
Pilz PNOZ m EF 4DI4DOR Bedienungsanleitung
Pilz
Pilz PSSu E F 4DI Bedienungsanleitung
Pilz
Pilz PNOZ ms3p Bedienungsanleitung
Pilz
Pilz PSSu E F 2DI 60-R Bedienungsanleitung
Pilz
Pilz PNOZ mi1p Bedienungsanleitung
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
