Pilz PSSu E PS-P +/-10V Bedienungsanleitung

PSSu E PS-P +/-10V

Operating Manual 21921-EN-03

}Decentralised system PSSuniversal I/O

Preface

This document is a translation of the original document.

All rights to this documentation are reserved by Pilz GmbH & Co. KG. Copies may be made

for internal purposes. Suggestions and comments for improving this documentation will be

gratefully received.

Pilz®, PIT®, PMI®, PNOZ®, Primo®, PSEN®, PSS®, PVIS®, SafetyBUS p®,

SafetyEYE®, SafetyNET p®, the spirit of safety® are registered and protected trademarks

of Pilz GmbH & Co. KG in some countries.

SD means Secure Digital

Contents

Operating Manual PSSu E PS-P +/-10V

21921-EN-03 3

Section 1 Introduction 5

1.1 Validity of documentation 5

1.1.1 Retaining the documentation 5

1.2 Definition of symbols 5

Section 2 Overview 7

2.1 Module structure 7

2.2 Module features 7

2.3 Front view 8

Section 3 Safety 10

3.1 Intended use 10

3.2 Safety regulations 11

3.2.1 Use of qualified personnel 11

3.2.2 Warranty and liability 11

3.2.3 Disposal 11

Section 4 Function description 12

4.1 Block diagram 12

4.2 Module features 12

4.2.1 Integrated protection mechanisms 12

4.2.2 Functions 12

4.3 Configuration 13

Section 5 Installation 14

5.1 General installation guidelines 14

5.1.1 Dimensions 14

5.2 Installing the base module 16

5.3 Inserting and removing an electronic module 17

5.3.1 Inserting an electronic module 18

5.3.2 Removing an electronic module 19

5.3.3 Changing an electronic module during operation 19

Section 6 Wiring 20

6.1 General wiring guidelines 20

6.1.1 Mechanical connection of the base modules 20

6.2 Terminal configuration 22

Section 7 Operation 24

7.1 Messages 24

7.2 Display elements 24

7.2.1 Display elements for module diagnostics 24

Section 8 Technical details 25

Contents

Operating Manual PSSu E PS-P +/-10V

21921-EN-03 4

Section 9 Order reference 27

9.1 Product 27

9.2 Accessories 27

Introduction

Operating Manual PSSu E PS-P +/-10V

21921-EN-03 5

1 Introduction

1.1 Validity of documentation

This documentation is valid for the product PSSu E PS-P +/-10V. It is valid until new docu-

mentation is published.

This operating manual explains the function and operation, describes the installation and

provides guidelines on how to connect the product.

1.1.1 Retaining the documentation

This documentation is intended for instruction and should be retained for future reference.

1.2 Definition of symbols

Information that is particularly important is identified as follows:

DANGER!

This warning must be heeded! It warns of a hazardous situation that poses

an immediate threat of serious injury and death and indicates preventive

measures that can be taken.

WARNING!

This warning must be heeded! It warns of a hazardous situation that could

lead to serious injury and death and indicates preventive measures that can

be taken.

CAUTION!

This refers to a hazard that can lead to a less serious or minor injury plus

material damage, and also provides information on preventive measures

that can be taken.

NOTICE

This describes a situation in which the product or devices could be dam-

aged and also provides information on preventive measures that can be

taken. It also highlights areas within the text that are of particular import-

ance.

Introduction

Operating Manual PSSu E PS-P +/-10V

21921-EN-03 6

INFORMATION

This gives advice on applications and provides information on special fea-

tures.

Overview

Operating Manual PSSu E PS-P +/-10V

21921-EN-03 7

2 Overview

2.1 Module structure

A module consists of

}Electronic module and

}Base module with

– Screw terminals or

– Cage clamp terminals

The base modules are the carrier units for the electronic modules and are used to connect

the field wiring. The electronic modules are inserted on to the base modules and determine

the module's function.

Details of the base modules that can be used are available in the chapter entitled “Intended

Use”.

2.2 Module features

The product has the following features:

}Primary side of power supply

– The external supply is fed to the base module terminals.

– Voltage: 24V

}Secondary side of power supply

– The module supplies the output voltage to the base module terminals.

– No buffer when the supply voltage is interrupted

– Voltage: 10 V/-10 V

– Max. continuous output: 10,0 W

– Max. current at 10 V: 1,0 A

– Max. current at -10 V: 0,50 A

}LED for:

– External voltage

Overview

Operating Manual PSSu E PS-P +/-10V

21921-EN-03 8

2.3 Front view

2111

2212

2313

2414

13 23

14 24

PSSu E

PS-P+/-10V

-10V+10V

PSSu E

PS-P +/-10V

312591

000000

001

-10V +10V 1

Key:

}A: Electronic module

}B: Base module

}1: LED for module diagnostics

}2: Labelling strip with:

– Name of electronic module

– Order number

– Serial number

– Hardware version number

– 2D code

}3: Labelling strip for the terminal configuration on the base module

}4: Name of electronic module

}5: Connection level 1

}6: Connection level 2

}7: Connection level 3

}8: Connection level 4

Overview

Operating Manual PSSu E PS-P +/-10V

21921-EN-03 9

}9: Square mounting holes (connection levels 1, 2, 3 and 4)

– With screw to loosen/tighten the screw terminal on base modules with screw termin-

als

– With mechanism to operate the cage clamp on base modules with cage clamp ter-

minals

}10: Round connection holes (connection levels 1, 2, 3 and 4) for connecting the signal

lines

}11: Mounting slot for colour marker to label the connection level (connection levels 1, 2,

3 and 4)

Safety

Operating Manual PSSu E PS-P +/-10V

21921-EN-03 10

3 Safety

3.1 Intended use

The module may be used to convert a 24 V protective extra low voltage, in order to supply

sensors and actuators connected to the PSSuniversal system.

Intended use includes making the electrical installation EMC-compliant. Please refer to the

guidelines stated in the "PSSuniversal Installation Manual". The module is designed for use

in an industrial environment. It is not suitable for use in a domestic environment, as this can

lead to interference.

The following is deemed improper use in particular:

}Any component, technical or electrical modification to the module

}Use of the module outside the areas described in this manual

}Any use of the module that is not in accordance with the technical details.

INFORMATION

The module is supported by

}PSSuniversal Configurator and PSSuniversal Assistant from Version

1.5.0

}PAS4000 from Version 1.1.1

– We recommend that you always use the latest version (download

from www.pilz.de).

The PSSu E PS-P +/-10V module may be used in conjunction with the following base mod-

ules:

}PSSu BP 1/8 S

}PSSu BP 1/8 C

}PSSu BP 1/12 S

}PSSu BP 1/12 C

}PSSu BP-C1 1/12 S

}PSSu BP-C1 1/12 C

Inhaltsverzeichnis

Andere Pilz E/A-System Handbücher

Pilz

Pilz PSSu H FS SN SD Bedienungsanleitung

Pilz

Pilz PSSu E S 2AO I Bedienungsanleitung

Pilz

Pilz PSSu E F AI U Bedienungsanleitung

Pilz

Pilz PSSu E F PS Bedienungsanleitung

Pilz

Pilz PSS u2 ES 8DOD 0.5A Bedienungsanleitung

Pilz

Pilz PSSu E S 2AO U Bedienungsanleitung

Pilz

Pilz PSS u2 ES 16PT 0V Bedienungsanleitung

Pilz

Pilz PSSuniversal Benutzerhandbuch

Pilz

Pilz PSSu E S 4DO 0.5-D Bedienungsanleitung

Pilz

Pilz PSS u2 ES 4DOD 0.5A Bedienungsanleitung

Pilz

Pilz PSSuniversal PSSu E F ABS SSI Bedienungsanleitung

Pilz

Pilz PSSu K S 8DI 8DO 0.5 Bedienungsanleitung

Pilz

Pilz PSS u2 ES 4DOD 2A Bedienungsanleitung

Pilz

Pilz PSSu E F INC Bedienungsanleitung

Pilz

Pilz PSSu E F PS-P Bedienungsanleitung

Pilz

Pilz PSS u2 EF 8DO 0.5A Bedienungsanleitung

Pilz

Pilz PSS u2 ES 8DID Bedienungsanleitung

Pilz

Pilz PSSu H F PN o Bedienungsanleitung

Pilz

Pilz PSSu H FS2 SN SD Bedienungsanleitung

Pilz

Pilz PNOZ msi9p Bedienungsanleitung

Pilz

Pilz PSSu E S 4AO U Bedienungsanleitung

Pilz

Pilz PSS u2 ES 8PTD 24V 0V Bedienungsanleitung

Pilz

Pilz PSS u2 ES 6DI 120V AC Bedienungsanleitung

Pilz

Pilz PSSu H SB-T Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung