Polaris FR-1516 Bedienungsanleitung

FORD

RANGER

FR-1516 INSTALLATION

INSTRUCTIONS

Thank you for purchasing the Polaris

Ford Ranger FR-1516 in-dash unit.

Before removal and installation, be

sure to thoroughly read these

instructions. Keep these instructions

with your vehicle for future reference

This installation guide is for reference

only. Polaris takes no responsibility for

any damage caused to any vehicle

through incorrect installation, unsafe

practices or poor workmanship.

Warranty for this product is 1year

from the date of purchase, however

warranty will be void if:

- The unit is tampered with,

damaged or modified in any way

- Reverse camera cable is cut or

modified in any way

- Reverse camera is subjected to

over voltage

- The navigation SD card is

damaged or tampered with in

any way (this includes installing

foreign mapping or software)

If you have any questions

concerning the installation,

warranty or operation of the unit,

please contact POLARIS on

1300 555 514

Warranty Terms

The Ford Ranger FR-1516 is covered for 1year and includes:

Defective Equipment

Defective cables

Not covered under warranty:

Abuse

Improper installation

Alteration to cables (this includes cutting of any cables)

Accidents

Prior to installing the unit, please make sure that you have all the parts from the box and the

necessary tools to complete the installation.

Tools required

1. Trim tools

2. Cable ties

3. Soldering Iron & Solder

4. Electrical Tape

5. Heat shrink

6. Burner for Heat shrink

7. Step through drill

8. 7mm socket

9. Multi tip set

10. Side cutters

11. Drill/Philips head screwdriver

12. Split conduit

13. Yellow Tongue (long strike,

approx. 3-4 metres)

14. Short strike (approx. 1 metre)

15. Power cable

16. 10mm spanner

SECTION 1-UNIT PREP

First, remove glove box for easy access, by opening

and squeezing in the two edges. There will be two

white plastic pins near the hinge that need to be

removed so the glove box can be pulled out and set

aside. (NOTE WHICH WAY PINS GO IN FOR

REASSEMBLY)

Now using your fingers or a trim tool, remove the

top dash tray, after doing so you will need to use

step through drill piece, and drill a hole big enough

for the wiring loom to fit through.(Ensure that the

hole lines up with the plug on the head unit)

Grab the wiring loom and pass the plug end up

behind glove box until you see it peeping through

the left side of the dash tray, and feed it under the

plastic skin to the hole and then pull through hole.

SECTION 2-REVERSE CAMERA INSTALLATION

Run a long strike through the chassis rail from front

to rear

With the end of the strike hanging out, tape the

camera cable (large 4 pin), illumination wire and

reverse power wire onto it. Pulling carefully, pull the

strike through from the front of the vehicle, making

sure that you leave enough cable and wires at the

rear to plug in rear camera and wire up the two

wires.

Attach the number plate camera provided as shown

in the picture.

Mount the number plate back onto the vehicle

Now under the vehicle and behind the rear bumper,

connect the number plate camera plug to the

extension cable. Apply heat shrink over the

connection to avoid the plug coming loose.

SECTION 2 CONTINUED….

SECTION 3-REVERSE CAMERA WIRING

Open the back tail gate to get access to the two

screws that need to be undone in order to remove

the passenger side tail light.

Now tap into the reverse positive wire, red with

yellow stripe (Attach reverse power wire), and tap

into tail light wire, red and grey (Attach illumination

wire). After everything is soldered and taped,

reinstall tail light.

SECTION 3 CONTINUED...

Remove scuff plate and kick panel on the passenger

side of the vehicle, then lift up the carpet to locate

the grommet. Remove grommet and feed cable up

into the cab.

Using cutters, make an incision in the grommet so

that the cables can be fed through it. Once the

cables have been fed through the grommet making

sure there is enough cable to reach behind the glove

box, restore it to its original position.

From underneath the vehicle, pull any excess cable

through and apply conduit to all exposed

cable/wires, then push back into chassis rail and zip

tie conduit to chassis rail to ensure it doesn’t pull

back out. *

*when finished with the grommet and you have

made sure you have enough cable, silicon it up for

waterproofing.

Run the reverse camera cable and wires to glove box

area reaching the end of the wiring loom. Plug rear

camera into BACK CAM Plug on loom. Connect

reverse power wire to brown BACK wire in loom and

also connect illumination wire to orange ILL wire on

loom, making sure to solder the two wires and tape

all wires including camera plug so it doesn’t come

loose.

SECTION 4-WIRING DIAGRAM

Front camera

Back camera

Caravan camera

GPS antenna plug

To find BATT+ and ACC, remove scuff plate and kick panel of driver’s side. Using a test lamp, find

constant power for BATT+ and accessory power for ACC. (The plug circled has a grey with blue

stripe wire and this wire is generally ACC power, although not guaranteed with different year

models). Once all is soldered and taped run the wires from here under carpet and up through to

behind the glove box, connecting onto the loom. Put driver side trim back together.

SECTION 5-MOUNTING HEADUNIT & GPS

SECTION 6-REINSTALLING AND FINISHING

Before connecting up the head unit, you need to secure the GPS antenna under the top of the

dash using a square of double sided tape, and making sure that it’s not in the way of the head

unit clipping in. Run the blue plug up the right side of rectangular hole. Any extra GPS cable can

be bundled and shoved in under dash. Grab the FR-1516 in-dash and plug in the main harness,

then plug in the blue GPS plug. It’s advised that you test all the features before putting

everything back together. Once satisfied that everything is in working order. Push down firmly on

the unit until it clips in. (It should fit nicely, if it is having trouble clipping in, there is wiring in the

way and needs to be moved)

Stick GPS Blue Plug

Reinstall kick panel and scuff plate, making sure all is clipped in, make sure all loose or hanging

wires/cables are zip tied and neat. Reinstall your glove box by doing the reverse of removal

ensuring the white pins go back in the correct way. Now you have your finished product.

Andere Handbücher für FR-1516

Inhaltsverzeichnis

Andere Polaris Autozubehör Handbücher

Polaris

Polaris 2879719 Bedienungsanleitung

Polaris

Polaris 2880612 Bedienungsanleitung

Polaris

Polaris Mazda BT50 RW-50/15 Bedienungsanleitung

Polaris

Polaris ToyotaLUXX Bedienungsanleitung

Polaris

Polaris 2883419 Bedienungsanleitung

Polaris

Polaris SPORTSMAN PRO HD 2882242 Bedienungsanleitung

Polaris

Polaris RideCommand Bedienungsanleitung

Polaris

Polaris 2882353 Bedienungsanleitung

Polaris

Polaris 2878669 Bedienungsanleitung

Polaris

Polaris 2882167 Bedienungsanleitung

Polaris

Polaris RIDE COMMAND Bedienungsanleitung

Polaris

Polaris 2880290 Bedienungsanleitung

Polaris

Polaris 2879039 Bedienungsanleitung

Polaris

Polaris 2879373 Bedienungsanleitung

Polaris

Polaris 2880056 Bedienungsanleitung

Polaris

Polaris RW-50/15 Bedienungsanleitung

Polaris

Polaris 2882534 Bedienungsanleitung

Polaris

Polaris 2881529 Bedienungsanleitung

Polaris

Polaris 2882857 Bedienungsanleitung

Polaris

Polaris 2016 RZR 4 900 Bedienungsanleitung

Polaris

Polaris CM50 Bedienungsanleitung

Polaris

Polaris PROSPECTOR PRO Bedienungsanleitung

Polaris

Polaris 2878840 Bedienungsanleitung

Polaris

Polaris 2883687 Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung

Prorack

Prorack K1163 Bedienungsanleitung