Polaris 2884764 Bedienungsanleitung

BEFORE YOU BEGIN

Read these instructions and check to be sure all parts and tools are accounted for. Please retain these

installation instructions for future reference and parts ordering information.

APPLICATION

Verify accessory fitment at www.polaris.com.

KIT CONTENTS

REF QTY PART DESCRIPTION P/N AVAILABLE

SEPARATELY

AVAILABLE

SERVICE KIT

1 1 Mount Plate 1026122 n/a

2 1 Mid Mount 1026123 n/a

3 1 Bracket-Bumper Support, Upper 5265124 n/a

4 1 Handle Lock n/a n/a

5 1 Tightening Plate n/a n/a

6 1 Fairlead Adapter Plate n/a n/a

71 Lower Side Support Bracket n/a n/a

8 1 Kickstand Lever n/a n/a

Instr 9931129 Rev 01 2020-08 Page 1 of 8

P/N 2884764

PLOW MOUNT KIT

Instr 9931129 Rev 01 2020-08 Page 2 of 8

REF QTY PART DESCRIPTION P/N AVAILABLE

SEPARATELY

AVAILABLE

SERVICE KIT

9 1 Weldment Plate n/a 2208483

10 6 Screw–Hexflange, M8 x 1.25 x 25 n/a 2208483

11 2 Screw–Hexflange, M6 x 1.0 x 30 n/a 2208483

12 2 Screw–Hexflange, M10 x 1.25 x 25 n/a 2208483

13 2 Screw–Hex, M10 x 1.5 x 25 n/a 2208483

14 6 Nut–Flange, Nylon Locking, M8 x 1.25 n/a 2208483

15 2 Washer–10.5 x 20 x 2 n/a 2208483

16 2 Washer–10.2 x 18.1 x 2.2 n/a 2208483

17 2 Split Pin n/a 2208483

18 1 Pin n/a 2208483

19 1 Lock Pin n/a 2208483

20 1 Clevis Pin 16mm x 40mm n/a 2208483

21 1 Clevis Pin 9.87mm x 28mm n/a 2208483

22 1 Winch Link–Mid Size n/a 2205057

23 1 Nut–Nylon Locking, M10 x 1.5 n/a 2205057

TOOLS REQUIRED

• Safety Glasses

• Socket Set, Metric

• Wrench Set, Metric

• Socket Set, Torx®Bit

• Pliers, Needle Nose

• Torque Wrench

IMPORTANT

Your Plow Mount Kit is exclusively designed for your vehicle. Please read the installation instructions thoroughly

before beginning. Installation is easier if the vehicle is clean and free of debris. For your safety, and to ensure a

satisfactory installation, perform all installation steps correctly in the sequence shown.

INSTALLATION INSTRUCTIONS

VEHICLE PREPARATION

GENERAL

1. Shift vehicle transmission into Park.

2. Turn key to OFF position and remove from vehicle.

CENTER HOOD PANEL REMOVAL

1. Turn quarter-turn fasteners to unlock hood from

vehicle.

Instr 9931129 Rev 01 2020-08 Page 3 of 8

2. Move hood forward to remove from vehicle.

ACCESSORY INSTALLATION

1. Remove and keep two screws A. Remove winch

cover.

2. Remove and keep eight screws Bto remove front

fascia.

3. Disconnect headlight connectors and accent light

connectors.

4. Install upper bumper bracket support eusing

screws dand weldment plate o.

Instr 9931129 Rev 01 2020-08 Page 4 of 8

5. Install fairlead.

• If fairlead uses standard mounting holes then

install winch fairlead onto mounting plate using

screws aand nuts g.

• If fairlead uses inner holes then fairlead adapter

is required. Install fairlead and fairlead adapter

yto mounting plate using screws aand nuts

6. Install mounting plate wusing screws aand nuts

7. Install tightening plate twith washers hand j

and screws f.

8. Torque screws a,d, and fto specification.

TORQUE

40 ft-lbs (54 N·m)

VEHICLE REASSEMBLY

GENERAL

1. Reconnect four light connectors.

Instr 9931129 Rev 01 2020-08 Page 5 of 8

2. Install front fascia with six screws B.

3. Install two screws s.

4. Install optional winch cover with screws A

CENTER HOOD PANEL INSTALLATION

1. Move hood rearward.

2. Turn quarter-turn fasteners to lock hood to vehicle.

Instr 9931129 Rev 01 2020-08 Page 6 of 8

OPERATION

HOOK UP ASSEMBLY

1. Attach plow hookup.

2. Insert pins C.

3. Insert split pins and bend to secure.

4. Install winch link 2@ into plow assembly.

5. Attach winch to winch link.

IMPORTANT

The first adjustment requires kickstand height

adjustment, depending on ground clearance. It may

be necessary to repeat this exercise if accessories

are added that affect ground clearance.

NOTICE

If vehicle height is too low, vehicle height may

require adjustment. Refer to owner's manual for

suspension adjustment procedures.

DISCONNECTING THE PLOW ASSEMBLY

1. Lower plow onto ground using winch until there is

no tension in cable.

2. Disconnect winch from winch link.

3. Lower kickstand until it locks. Kickstand shoe

should not touch the ground. If it is refer to

Kickstand Adjustment.

Instr 9931129 Rev 01 2020-08 Page 7 of 8

4. Pull up on handle.

5. Turn assembly away from vehicle.

6. Back vehicle in a straight line until push-frame

assembly is not touching vehicle.

CONNECTING THE PLOW ASSEMBLY

1. Align vehicle with assembly. Make sure pins are

lined up with opening on the push-frame assembly.

2. Drive forward until vehicle is fully engaged in

attachment plates on both sides.

3. Rotate assembly up by hand until hook engages

with upper mount of plow mount plate. If hook

does not fully engage check for snow and ice

accumulation on lower pins of the mount plate.

The kickstand should be off of the ground. If it is

not refer to Kickstand adjustment.

4. Connect winch hook to winch link.

5. Lift plow assembly with winch until kickstand is

retracted automatically. Plow should be in top 1/3

of its travel.

WINCH LINK ADJUSTMENT

CAUTION

The plow could become disconnected during

adjustment. Always lower plow to the ground when

making adjustments to avoid injury.

1. Attach plow assembly to vehicle and connect

winch cable to winch link.

2. Raise plow until winch auto stop engages or winch

hook contacts fairlead.

3. Lift up blade by hand to determine if it is at

maximum lift height.

4. Adjust winch link so plow is at maximum lift height

when winch auto stop engages or the winch hook

contacts fairlead.

Instr 9931129 Rev 01 2020-08 Page 8 of 8

5. Lower plow to the ground and adjust nut on bottom

of winch link as required.

6. Repeat steps until maximum lift height is achieved.

KICKSTAND ADJUSTMENT

CAUTION

The plow could become disconnected during

adjustment. Always lower plow to the ground when

making adjustments to avoid injury.

The kickstand must support push frame so the

opening of push frame assembly lines up with mount

plate pins for easy installation and removal of plow

assembly.

1. Loosen jam nut Dand screw kickstand shoe up

or down to achieve desired height.

2. Check height to make sure hook up openings and

mount plate pins are aligned.

3. Tighten jam nut to secure kickstand in place.

NOTICE

It may be necessary to install jam nut on opposite

side of kickstand if additional adjustment is required.

ADJUSTMENT OF AUTO RETRACTING

KICKSTAND

CAUTION

The plow could become disconnected during

adjustment. Always lower plow to the ground when

making adjustments to avoid injury.

The auto retracting kickstand should be triggered

when cap of J-Rod makes contact with kickstand lever

of machine. This should take place in last 1/3 of

plow’s travel. Follow the steps below if kickstand fails

to release properly:

1. Make sure plow is achieving its maximum lift

height by lifting up on blade to make sure plow is

against stops at full lift. If it does not, refer to Winch

Link Adjustment.

2. Loosen jam nut on bottom of cap and screw cap in

or out to achieve desired adjustment.

3. Test kickstand assembly by putting kickstand

down and lifting plow system with winch to it’s max

lift height.

4. Repeat process until kickstand releases in top 1/3

of plow’s travel.

5. Tighten jam nut to secure cap in place.

INSTRUCTION FEEDBACK FORM

A feedback form has been created for the installer to provide any comments,

questions or concerns about the installation instructions. The form is viewable on

mobile devices by scanning the QR code or by clicking HERE if viewing on a PC.

Inhaltsverzeichnis

Andere Polaris Autozubehör Handbücher

Polaris

Polaris 2882271 Bedienungsanleitung

Polaris

Polaris 2880612 Bedienungsanleitung

Polaris

Polaris PRO HD 3500 Bedienungsanleitung

Polaris

Polaris 2881529 Bedienungsanleitung

Polaris

Polaris 2882270 Bedienungsanleitung

Polaris

Polaris 2882857 Bedienungsanleitung

Polaris

Polaris 2880290 Bedienungsanleitung

Polaris

Polaris RIDE COMMAND Bedienungsanleitung

Polaris

Polaris CM50 Bedienungsanleitung

Polaris

Polaris RW-50/15 Bedienungsanleitung

Polaris

Polaris ToyotaLUXX Bedienungsanleitung

Polaris

Polaris RIDE COMMAND Bedienungsanleitung

Polaris

Polaris 2879719 Bedienungsanleitung

Polaris

Polaris HomeLink 2882082 Bedienungsanleitung

Polaris

Polaris 2878839 Bedienungsanleitung

Polaris

Polaris 2016 RZR 4 900 Bedienungsanleitung

Polaris

Polaris BT50 Luxx Bedienungsanleitung

Polaris

Polaris 2878669 Bedienungsanleitung

Polaris

Polaris 2883687 Bedienungsanleitung

Polaris

Polaris 2878840 Bedienungsanleitung

Polaris

Polaris 2881113 Bedienungsanleitung

Polaris

Polaris 2876958 Bedienungsanleitung

Polaris

Polaris Mazda BT50 RW-50/15 Bedienungsanleitung

Polaris

Polaris HK-338 Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung

Prorack

Prorack K1163 Bedienungsanleitung