Polaris Mazda BT50 RW-50/15 Bedienungsanleitung

Thank you for purchasing the Polaris Mazda BT50 RW-50/15 in-dash unit.

Before removal and installation, be sure to thoroughly read these instructions.

Keep these instructions with your vehicle records for future reference.

Mazda BT-50 RW-50/15

installation instructions

Version 3

This installation guide is for reference only. Polaris takes no responsibility for any

damage caused to any vehicle through incorrect installation, unsafe practices or poor

workmanship.

Warranty for this product is 1 year from date of purchase, however warranty will be

void if:

• The unit is tampered with, damaged or modified in anyway.

• Reverse camera cable is cut or modified in any way

• Reverse camera is subjected to over voltage

• The Navigation SD card is damaged or tampered with in any way (this includes in-

stalling foreign mapping or software onto the SD card)

Warranty Terms

The Mazda BT50 RW-50/15 is covered for 1 year and includes:

• Defective Equipment

• Defective Cables

Not Covered under warranty:

• Abuse

• Improper installation

• Alteration to cables (this includes cutting of any cables)

• Accidents

This Polaris BT50 RW-50/15 utilises the OEM CD player, AM/FM Radio and USB input.

If you have any specification or troubleshooting enquiries in regards to these func-

tions please refer to your owner’s manual.

If you have any questions concerning the installation, warranty or the operation of

the unit, please contact Polaris on 1300 555 514.

We hope that you enjoy the Polaris BT50 RW-50/15 in dash unit.

BT50-Installation-Guide-V3 (2020) 10/03/20 3:13 pm Page 1

F. Wiring Diagram

Connects to OEM Radio

Connects to OEM Radio plug

Connects to back of the

RW50/15 screen

Plugs into OEM Screen plug

Connects to

back of the

RW50/15

screen

Connects to

back of the

RW50/15

screen

QUICK REFERENCE GUIDE

When the manual refers to ‘TOP SECTION’ this is the area located where the OEM 3.5”

screen was originally mounted

When the manual refers to ‘OEM CD HOUSING AREA’ this is the area located where the

OEM CD was originally mounted

When the manual refers to ‘OEM’, this means original equipment manufacturer.

Connects to OEM CD player harness

Connects to OEM CD player

BT50-Installation-Guide-V3 (2020) 10/03/20 3:13 pm Page 2

Prior to installing the unit, please make sure that you have all

the parts from the box and the necessary tools to complete the

installation.

1. RW-50/15 Fascia

2. RW-50/15 8” Interface

Screen

3. Wiring Harness

4. Bluetooth External

Microphone

5. GPS External Antenna

6. Instruction Manual

7. Trim Tool

8. Rear Vision Camera

1. Trim tools

2. Cable tie

3. Electrical Tape

4. Heat shrink

5. Burner for Heat shrink

6. Small Terminal driver

7. Short Phillips head screwdriver

8. Multi tip set

9. Side cutters

10. Split conduit

11. Yellow Tongue (long strike, approx. 3-4 metres)

12. Short strike (approx. 1 metre)

1. RW-50/15 Fascia

4. Bluetooth External Microphone 5. GPS External Antenna +

Bracket & Screws 6. Instruction Manual

7. Trim Tool

8. Rear Vision Camera

3. Wiring Harness

2. RW-50/15 8” Interface Screen

Parts - Packing List

Tools required

BT50-Installation-Guide-V3 (2020) 10/03/20 3:13 pm Page 3

Important Installation tips

• We no longer recommend mounting the GPS Antenna underneath the dashboard;

please mount it on top of the dash in the right /left top corner near the windscreen.

• Prior to installation, please disconnect and turn off the OEM

Bluetooth function.

• If you are installing a front vision camera or a caravan/trailer

camera, you will need to turn these functions on via the factory setup, to do this:

- Go into Setup > Version > Factory setup > type in 1876

- To activate the forward vision camera, please change

FRONT CAM from off to on

- To activate the caravan / trailer camera, please change

the REAR CAM from single to double.

• When testing the navigation function, please ensure that you allow the program to

completely load before activating any other function on the unit (this includes activat-

ing the reverse camera).

• When installing any screws into the RW50/15 fascia, be sure not to overtighten.

We recommend using a screwdriver and not a drill because it can create a hairline

crack that will deteriorate over time causing the fascia to crack.

BT50-Installation-Guide-V3 (2020) 10/03/20 3:13 pm Page 4

Step 1 - Remove Air conditioning panel

1. Starting from the bottom, use trim

tools to remove air conditioning

controls

2. Unplug harness and set

air conditioning controls aside

1. Use trim tools to

remove fascia panel

2. Gently pull fascia panel

out

3. Unplug button panel and

set OEM fascia panel aside

1. Remove 2 screws holding

OEM screen in place

2. Unplug harness and set

OEM screen aside

3. Remove 2 screws holding

the OEM CD housing

in place.

Step 2 - Remove Fascia Panel

Step 3 - Remove OEM Screen and CD Housing

4. Unplug harness and set

OEM CD housing aside for

now. 5

WARNING

When removing the air-conditioning

panel, fascia, OEM screen and CD housing,

do not use excessive force to pull the

panels out as there are harnesses that

need to be unplugged before complete

removal.

BT50-Installation-Guide-V3 (2020) 10/03/20 3:13 pm Page 5

1.Remove door rubber and

the driver’s pillar trim

2. Mount microphone in the

top right hand corner of the

windscreen

3. Use lever to drop steering

wheel column down

4. Remove trim around

instrument cluster panel

7. Tape Bluetooth mic cable onto strike and pull through to

the instrument cluster panel area

5. Unplug instrument cluster

panel and remove

8. You can now remove the

tape and feed the Bluetooth

mic cable into the

TOP SECTION

9. Tidy up cabling running

down the side of the

driver’s piller and reinstall

rubber and trim

10. While the instrument cluster

panel is removed, we suggest

feeding plug A, B & C from the

OEM CD housing area up to the

top section

11. This will then leave plug D & E

from the wiring harness hanging in

the CD housing area

Step 4 - Prepare all the cabling in preparation for

the head unit to be installed.

A. External Bluetooth Microphone

6. Feed short strike through A

piller hole and feed into the

instrument cluster panel area

BT50-Installation-Guide-V3 (2020) 10/03/20 3:13 pm Page 6

B. IPOD & USB Cable

1. Remove glove box - gently

push in sides to release.

13. Plug harness back into

instrument cluster panel and

remount.

2. Unclip OEM USB and AUX

cable for now, so that you can

remove the glove box

completely.

3. Feed RW50/15 USB cable

from top section down into

the glove box area

C. External Antenna

14. Reinstall trim.

NOTE: please make sure the

bottom section of the trim

goes underneath the two

reset dials.

12. Connect plug Cinto OEM

plug located in the

TOP SECTION and connect plug

Dinto the OEM plug located in

the OEM CD housing area

We no longer recommend mounting the GPS Antenna underneath the dashboard; please

mount it on top of the dash in the right /left top corner near the windscreen.

BT50-Installation-Guide-V3 (2020) 10/03/20 3:13 pm Page 7

6. Connect camera plug to the extension

cable. Apply heat shrink over connection

to avoid the plug coming loose.

1. Run your long strike through chassis rail from front to rear.

2. Tape camera cable (large 4 pin din) onto strike at the rear of the vehicle.

3. Pull strike through from front of the vehicle - making sure that you leave enough

cable at the rear so that you can plug the camera cable in.

7. Remove kick panel and scuff plate

on passenger front side of vehicle

8. Lift carpet up to find grommet

9. Remove grommet and feed cable

through

10. Use cutters to make an incision in

grommet so that you feed cable through it.

Once you have fed the cable through the

grommet restore grommet back into its

original position.

11. Pull excess cable then apply

conduit to all exposed cable.

12. Run reverse camera cable up into

glove box area.

13. Feed camera cable up to

top section

E. Rear Camera

14. Position wiring harness up

in the top section and plug

the camera cable into the

reverse camera plug input

Notes:

Once you have repositioned the grommet after

feeding the reverse camera cable through,

we recommend applying silastic around the outside

the cable for waterproofing

Once you have fed the camera cable from the glove

box area up to the TOP SECTION, we recommend

that you cable tie any loose cables.

4. Attach the number plate camera

onto number plate (as shown above)

5. Mount number plate back

onto the vehicle.

BT50-Installation-Guide-V3 (2020) 10/03/20 3:14 pm Page 8

Connects to OEM Radio

Connects to OEM Radio plug

Connects to back of the

RW50/15 screen

Plugs into OEM Screen plug

Connects to

back of the

RW50/15

screen

Connects to

back of the

RW50/15

screen

Connects to OEM CD player harness

Connects to OEM CD player

Step 5 - Mount OEM CD player

2. Connect PLUG E into the

back of OEM CD player

3. Plug the radio antenna into

the back of the OEM CD player

3. Mount the OEM CD player back

into position and secure in place

with the original screws.

F. Wiring Diagram

PLEASE NOTE:

If your Mazda BT-50 originally had the OEM GPS system installed, you need to

plug in a different radio antenna. Instead of using the radio antenna that normally

plugs into the back of the OEM CD housing

(the connector that you originally unplugged), you must use the radio antenna that

was originally plugged into the the back of the OEM GPS Screen (it is the black

connector).

1. Before re-mounting the OEM

CD housing we suggest posi-

tioning the power amplifier

box just behind it.

BT50-Installation-Guide-V3 (2020) 10/03/20 3:14 pm Page 9

1. Grab the OEM fascia and

remove all 9 clips and set aside.

2. Remove the 10 screws holding the

button panel and air conditioning

vents in place - set aside.

Step 6 - Prepare the BT50 RW-50/15 OEM fascia

3. Position the button panel and air condi-

tioning vents onto the RW-50/15 fascia

and secure in place with the 10 original

screws.

4. Clip the 9 clips onto the RW-50/15

fascia

5. Use the 2 screws to attach the

RW50/15 screen to the fascia.

IMPORTANT: When installing any screws into the RW50/15 fascia, be sure not to overtighten.

We recommend using a screwdriver and not a drill because it can create a hairline crack that

will deteriorate over time causing the fascia to crack.

6. Finished product.

BT50-Installation-Guide-V3 (2020) 10/03/20 3:14 pm Page 10

Andere Handbücher für Mazda BT50 RW-50/15

Inhaltsverzeichnis

Andere Polaris Autozubehör Handbücher

Polaris

Polaris 2879953 Bedienungsanleitung

Polaris

Polaris 2880056 Bedienungsanleitung

Polaris

Polaris 2877466 Bedienungsanleitung

Polaris

Polaris 2880411 Bedienungsanleitung

Polaris

Polaris PROSPECTOR PRO Bedienungsanleitung

Polaris

Polaris RideCommand Bedienungsanleitung

Polaris

Polaris 2879976 Bedienungsanleitung

Polaris

Polaris 2879719 Bedienungsanleitung

Polaris

Polaris 2884764 Bedienungsanleitung

Polaris

Polaris 2883455 Bedienungsanleitung

Polaris

Polaris 2880612 Bedienungsanleitung

Polaris

Polaris 2882167 Bedienungsanleitung

Polaris

Polaris HomeLink 2882082 Bedienungsanleitung

Polaris

Polaris RW-50/15 Bedienungsanleitung

Polaris

Polaris 2880325 Bedienungsanleitung

Polaris

Polaris 2016 RZR 4 900 Bedienungsanleitung

Polaris

Polaris BT50 Luxx Bedienungsanleitung

Polaris

Polaris 2883419 Bedienungsanleitung

Polaris

Polaris FR-1516 Bedienungsanleitung

Polaris

Polaris 2879039 Bedienungsanleitung

Polaris

Polaris PRO HD 3500 Bedienungsanleitung

Polaris

Polaris 2878669 Bedienungsanleitung

Polaris

Polaris 2882353 Bedienungsanleitung

Polaris

Polaris 2882270 Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung

Prorack

Prorack K1163 Bedienungsanleitung