Prestige APS-20B Bedienungsanleitung

Model APS-20B

Owner's Manual

3 Button Vehicle Alarm System

With Channel 2 Auxiliary Output

FEATURES:

2 Three Button RF Transmitters

Three Channel Code Learning Receiver

Remote Panic In All Modes

Built-InParkingLightOutput

LED Status Indicator

Multi-ToneSiren

True Last Door Arming

Channel2AuxiliaryOutput

OPTIONS:

Remote Trunk Release

Remote Power Window Control

Remote Garage Door Interface

Remote Engine Starter

Single or Dual Stage Shock Sensor

StarterInterrupt

Keyless Entry

Ignition Control Door-Locks

Page 1

YourAPS-20BVehicleAlarm System has many features and available options some of which

mustbe selected attime of installation. Foryour reference,thelist onthe back pageof this

manual shows what features and options have been installed with this particular system.

Consultyourinstalling dealer foroptionsthatmay have been installedandarenot listed.

ARMINGTHESYSTEM -ACTIVE

1.Turn the engineoff, exit thevehicle and closeall doors.

2.Pressand release thelockbutton of yourkeychain transmitter onetime.

The parking lights will flash once, the siren will chirp once, and the dash mounted LED will

begintoflashslowlyconfirming the system isarmed. Ifyouhavetheoptionaldoorlock/unlock

circuitinstalled, the doorswillalso lock.

SILENTARMING- ACTIVE

1.Turn the engineoff, exit thevehicle and closeall doors.

2.Press andhold the lockbutton ofyour key chain transmitter fortwo seconds.

The parking lights will flash once and the dash mounted LED will begin to flash slowly

confirmingthe system isarmed. The siren willnot chirp. If youhave the optionaldoor lock/

unlockcircuit installed, thedoorswill lock.

ARMINGTHESYSTEM - PASSIVE(AUTOMATIC)

Ifthe passive armingfeaturehas been selected:

Turnthe engine off,exit the vehicleand close alldoors.

The dash mounted LED will immediately begin to flash rapidly indicating that the 30 second

passivearmingtimerhasbegun. IftheLEDdoesnotbegin to flash rapidly,then youhaveleft

adoor, hoodortrunk ajar. Closingthis entrypointwillallow the armingcycleto begin. If any

entrypointisopenedduringthe30secondarmingcycle,armingwillbesuspended. Whenall

entrypoints are closed,the arming cyclewillbegin again. At theend of the30 seconds, the

parkinglightswillflashonce,thesiren will chirp once and thedashmountedLEDwillbeginto

flashslowlyconfirmingthesystemis armed. If the sirendidnotsoundwhenarming,thenthe

chirps have been turned off. Please refer to the section titled "Eliminating the Arm/Disarm

Chirps" later in this manual. Passive door locking is a selectable feature. If you have the

optionaldoorlock/unlockcircuitinstalled,thedoorsmayormaynotlockpassivelydependent

uponthesetupduringinstallation.

PROTECTIONWHILETHESYSTEMISARMED:

Whenever the system is armed, opening any protected entry point, (i.e.; hood, trunk, or

doors),willcausethealarmtotriggerimmediately. The siren will soundandtheparkinglights

willflashfor30seconds, then stop andresettocontinuetomonitor all protected entrypoints.

Ifthethief happened toleavethe entry pointopen,the system willsoundfor six consecutive

30secondcycles then shutdownand reset, isolatingthetriggeredzone, while continuingto

monitorandprotect all other zones.

Whenever the system is armed, the dash mounted LED will slowly flash. This serves as a

visualdeterrenttoapotentialthief. This LED is averylowcurrentlightemittingdiodeand will

notcause the batteryto draineven if leftunattended for longperiods of time.

Ifthe

optional

shocksensor isinstalled,anystrongimpacttothe vehicle will cause theshock

Page 2

Page 3

detectorto triggerthe alarm whenarmed. If the

optional

2-stageshock sensoris installed,

anylesserimpactwillcausethepre-detectstage of the shock sensor toemitaseriesofshort

warningtones fromthe siren when armed.

Iftheoptional starter interruptisinstalled the vehiclestartercircuitis disabled, evenwiththe

ignitionkey the vehiclewillnot start.

DISARMINGTHESYSTEM

Asyouapproach the vehicle,pressandrelease the unlockbuttonon the keychaintransmit-

ter.

Theparkinglightswillflashtwotimes, the siren will chirp twiceandthedashmountedLEDwill

turnoff. If you havethe optional doorlock/unlock circuit installed,thedoors willunlock.

Note: Ifthepassivearming mode was selectedatthetimeof installation, the dashmounted

LEDwill start flashingrapidly indicating thatthe systemisrearming. Opening anydoorwill

suspendtheautomaticarming.

Iftheparking lights flashed threetimesandthe siren chirpsfourtimes,thisindicates that the

alarmsystemhadbeen triggeredinyourabsence. Beforeturningontheignitionkey,examine

thedashmounted LED's flashpattern. Thenumber of flashesidentifiesthe triggered zone.

Foradditionalinformation,refertoINTRUSIONWARNINGSIGNALSfoundlaterinthismanual.

If the siren did not sound upon disarm, then the chirps have been turned off. Refer to the

sectiontitledELIMINATINGTHEARM/DISARMCHIRPS.

SILENTDISARMING

1. Asyouapproach thevehicle, pressandholdtheunlock buttonofyourkeychaintransmitter

for two seconds, or until the system responds.

Theparkinglightswill flash twiceandthedashmounted LED will turnoff,confirmingthatthe

systemisdisarmed. Thesiren will not chirp. Ifyouhavetheoptional door lock/unlock circuit

installed,thedoors will unlock.

Note: Ifthepassivearmingmodewasselectedattimeofinstallation,thedashmountedLED

will start flashing rapidly indicating that the system is rearming. Opening any door will

suspendtheautomaticarming.

Iftheparking lights flashed threetimesandthe siren chirpsfourtimes,thisindicates that the

alarmsystemhad been triggeredinyourabsence.

VALET/PROGRAM/MANUALOVERRIDESWITCH

Thevaletswitchallows youtotemporarilypreventthealarmfromarming,eliminating theneed

to hand your keychain transmitter to parking attendants or garage mechanics. When the

system is in the valet mode, all alarm functions are by-passed, however the remote panic

feature,andtheoptionalremotedoor lock/unlock will remain operational.

Toenterthevaletmode:

1. Start with the valet switch in the "off" position

2.Turn the ignitionswitchto the "on"position.

3.Within 10seconds of step 2, flipthe valetswitch to the "on" position.

ThedashmountedLEDwillturnonsolidindicatingthatthevaletmodehassuccessfullybeen

entered.

Page 4

Toreturn to thenormal, (alarm mode),operation, move thevalet switch tothe "off"position

anytime the ignition switchisin the onposition.

Note:Inthe event thatyoulose your keychaintransmitter or thetransmitterfails to operate

thealarmsystem,thevaletswitchcan be used to disarm thealarm. Thisisreferredtoasthe

"ManualOverride". Todisarmthealarm:

1.Open thedoor with thevehicle doorkey. (The siren willsound)

2.Turn the ignitionswitchto the "on"position.

3.Flip the valet/overrideswitchto the"on"position.

Thesystemwilldisarmand the sirenwillstopsounding,allowingtheenginetobestarted,and

thevehicleto be operatednormally. Always remembertomove the valetswitchbackto the

"off"position toallow the passivearming and optional starter interruptfeatures to beoper-

ablethenext time youparkthevehicle.

INTRUSIONWARNINGSIGNAL

This systemwill inform youif anintrusionattempt hasoccurred while youwere away from

thevehicle. Upondisarm,the siren will chirp4timesandthe parking lights willflash3times.

Enterthe vehicle and

before

turning on theignitionswitch, observe theLEDflash pattern.

Ifthe LED flashestwo times...pause, twotimes...pause etc., thenan intrusion attemptwas

made to open the hood or trunk, or an impact or a strong vibration was applied that the

optionalshock sensordetected. Check thevehicle for indications of forcedentry tothese

openings,or signs ofglassbreakage or bodydamage.

IftheLEDflashesthreetimes...pause, three times...pause etc.,thenanintrusionattemptwas

madeto the vehicledoors. Check alldoorsfor indicationsof forced entry.

Note:TheLEDintrusion warning indicationsarestored in thesystem'smemory and willbe

erasedwhen theignition switchis turned on.

ELIMINATINGTHEARM/DISARMCHIRPS

You can selectively eliminate the normal arm or disarm chirps by holding the respective

transmitter button slightly longer when arming and disarming. This will prevent the siren

chirpsforonearmor disarm cycle. Ifyoufind thisinconvenientand wish toeliminate these

chirpspermanently,

1. Start with the valet switch in the "off" position.

2.Turn theignition switch "on" then "off".

3. Within 10 seconds of turning off the ignition, flip the valet switch "on", "off", "on", "off",

"on", "off".

4.Ifthechirpswereon before you started,thesirenwillemit2shortchirps indicating that the

chirpsare now off. Ifthe chirpswereoff beforeyou started, thesiren will emitone short

chirpindicating thatthe chirps arenow on.

REMOTEPANICOPERATION

Thelock and unlockbuttonsof your keychaintransmitteralso serves asapanic switch and

willcause the sirento sound ondemand. To usethe panicfeature, you mustbe within the

system's maximum operating range. In an emergency situation, to use the panic feature,

pressand holdeither the lock or unlockbutton ofyour keychaintransmitter for 3seconds.

Page 5

This will cause the lights to flash, the siren to sound. The panic mode will continue for 30

secondsand then reset.

To disengage the panic feature before the 30 seconds are up, press and hold the lock or

unlockbutton of yourkeychain transmitter for3 seconds.

While the panic mode is engaged, the doors can be remotely locked and unlocked via the

transmitterbypressingthelock or unlock buttonmomentarily.

ADDITIONALREMOTEFUNCTIONCHANNEL2

The system has an additional feature, (Channel 2) , that can be connected to a number of

differentoptional accessories. Some ofthemore commonusesfor this channelare:

!RemoteTrunkRelease

!RemoteWindowClose

!RemoteGarageDoorInterface

To operate the accessory associated with Channel 2, press and

hold

the option button of

yourkeychain transmitter forthree seconds.

NOTE: Youmayaccessthe Channel2commandregardlessofwhetherthesystemis"armed"

or "disarmed", but not when the ignition switch is in the on position. This is to prevent the

outputfromaccidentally opening thevehicle'strunkwhen the vehicleisin motion.

IGNITIONDOORLOCKING/UNLOCKING

When connected to a vehicle's power door lock system the unit is capable of being pro-

grammedfor the addedsafetyand security ofignitioncontrolled door lockingandunlocking.

These features are separate, so the unit may be programmed for one, or both, or neither.

Thesefeatures can onlybeused if theoptional door lock/unlock circuitisinstalled.

Whentheignition door locking featureisprogrammed,thesystem will cause alldoorlocksto

lock whenever the ignition switch is turned from the "off" to "on" position, (providing that all

doorsare closed atthattime). All doors willlockapproximately 2 secondsafter the vehicle's

ignition switch is turned on. This is a nice feature for maintaining the personal safety of the

occupantsof the vehicle,inan effortless and automaticmanner.

When the ignitiondoorunlocking feature isprogrammed,system will causealldoor locks to

unlock whenever the ignition switch is turned from the "on" to "off" position. All doors will

unlockimmediately after thevehicle'signition switch isturnedoff.

As stated these features are programmed separately, so you may chose to use one, both,

or neither. Please consult with your dealer to consider your options.

SYSTEMFUNCTIONSATAGLANCE

ALARM LED INDICATORS:

RAPID FLASHING = PASSIVE ARMING

SLOW FLASHING = ARMED

OFF = DISARMED

ON SOLID = VALET MODE

2 FLASH...PAUSE = HOOD/TRUNK/SHOCK INTRUSION

3 FLASH...PAUSE = DOOR INTRUSION

SIREN CHIRP INDICATION:

1 CHIRP = ARM

2 CHIRPS = DISARMED

3 CHIRPS = ARMING WITH ENTRY POINT OPENED

4 CHIRPS = DISARM AFTER INTRUSION

CONTINUOUS = TRIGGERED/PANIC MODE

ALARM PARKING LAMP INDICATIONS:

1 FLASH = ARM

2 FLASHES = DISARM

3 FLASHES = DISARM AFTER INTRUSION

CONTINUOUSFLASH = PANICMODE

SELECTABLEFEATURES:

"PASSIVEARMING

"ACTIVEARMING

"IGNITIONCONTROLLEDDOORLOCK

"IGNITIONCONTROLLEDDOORUNLOCK

"PASSIVEDOORLOCKING

"CHIRPSON

"CHIRPSOFF

Page 6

128-6186A

Inhaltsverzeichnis

Andere Prestige Autoalarmanlage Handbücher

Prestige

Prestige PE1BZ Bedienungsanleitung

Prestige

Prestige 1286520 Bedienungsanleitung

Prestige

Prestige Prestige Platinum APS 600 Bedienungsanleitung

Prestige

Prestige Prestige 128-7853 Bedienungsanleitung

Prestige

Prestige APS-787E Bedienungsanleitung

Prestige

Prestige APS596Z Bedienungsanleitung

Prestige

Prestige 1286795 Bedienungsanleitung

Prestige

Prestige APS-140 Bedienungsanleitung

Prestige

Prestige APS-20B Bedienungsanleitung

Prestige

Prestige APS-997C Bedienungsanleitung

Prestige

Prestige Platinum APS 996 Bedienungsanleitung

Prestige

Prestige 1286469 Bedienungsanleitung

Prestige

Prestige Prestige Platinum 128-8128 Bedienungsanleitung

Prestige

Prestige Prestige Platinum 128-8122 Bedienungsanleitung

Prestige

Prestige Platinum+ APS-596 Bedienungsanleitung

Prestige

Prestige 1286445 Betriebsanleitung

Prestige

Prestige APS-25-CL Bedienungsanleitung

Prestige

Prestige 5WTX Betriebsanleitung

Prestige

Prestige 1286458 Bedienungsanleitung

Prestige

Prestige Prestige 128-4246A Bedienungsanleitung

Prestige

Prestige Prestige Platinum APS-510C Bedienungsanleitung

Prestige

Prestige APS-596E Bedienungsanleitung

Prestige

Prestige APS-25E Bedienungsanleitung

Prestige

Prestige APS-922E Bedienungsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken

Clifford

Clifford 3606X Bedienungsanleitung

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum+ APS-511C Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Viper

Viper 4708V Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Audiovox

Audiovox Auto Security XR91 Betriebsanleitung

Clifford

Clifford Sabre II Bedienungsanleitung

CrimeStopper

CrimeStopper CS-8717 Kurzanleitung

Ultra Start

Ultra Start 450 SERIES Bedienungsanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Excalibur

Excalibur AL-1860-EDPB Bedienungsanleitung

Clifford

Clifford CYBER 2 Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung