Prestige APS-25E Bedienungsanleitung

128-9321

Page 1/8

Page 1

PATENTED: www.voxxintl.com/company/patents

Model APS-25E

3 Button Remote Security

System Owner's Manual

FCC COMPLIANCE

This device complies with Part 15 of the FCC rules and with RSS-210 of Industry

Canada.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including any interference

that may cause undesired operation.

Warning!

Changes or modications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment

NOTE:The manufacturer is not responsible for any radio or TV interference

caused by unauthorized modications to this equipment. Such modications

could void the user’s authority to operate the equipment

Table Of Contents:

Introduction Features and Options Page 2

Arming The System Page 3 - 4

Protection While Armed Page 4

Disarming Your System Page 4

Intrusion Signals Page 4

Valet Override, Programming & Safety Control Switch Page 5

Manually Overriding Your System Page 5

Eliminating the Arm/Disarm Chirps Page 5

Remote Panic Operation Page 6

Trunk Release/Optional Device Channels Page 6

Replacement or Additional Transmitters Programming Page 7

Transmitter Battery Replacement Page 7

System Features At A Glance Page 8

128-9321

Page 2/8

Page 2

PRESTIGE

Congratulations! Your purchase of this state-of-the-art security system

expresses a deep concern for the security of your vehicle, its contents,

and passengers. To fully appreciate the many functions and safeguards

incorporated in this system, please spend a few minutes reading this

manual. You may nd unexpected features that could mean the difference

between “protected” and “fully protected”.

FEATURES:

2 Three Button Programmable Code Hopping RF Transmitters

Three Channel Receiver ( capable of accepting 4 transmitters )

Code Learning

Remote Panic in all modes

Protected Valet

7 Function LED - Arm / Disarm / Zones 1, 2, & 3 / Valet / Arming

Intrusion Alert with Memory

 Audible Arm / Disarm / Defective Zone / Tamper Conrmation

Instant Siren Activation

Starter Disable

True Last Door Arming ( hardwire only )

Defective Zone By - Pass

Hardwire or Voltage Sense Selectable

Active or Passive Arming Selectable

User Programmable Permanent Chirp Delete

6 Tone Multi-Tone Siren

Additional Negative Trigger Input

RF Inhibit with Ignition On

Parking Light Flasher

Plug In Dual Stage Shock Sensor

OPTIONS:

Remote Trunk Release

Remote Keyless Entry

Multiple Vehicle Capable

Remote Starter

Remote Power Window Roll Up

128-9321

Page 3/8

Page 3

ARMING THE SYSTEM: (ACTIVE)

1. Turn off the engine, exit the vehicle, and close and lock all doors, hood and

trunk.

2. Press and release the Lock button on the keychain transmitter. The siren

will "chirp" once, the vehicle's parking lights will ash once, the doors will

lock (optional) and the dash mounted LED will begin to slowly ash.

WARNING! Excessive pressure on the transmitter buttons will damage the in-

ternal components on the circuit board. All that is required is a light

push to the button.

NOTE: If the siren "chirped" three times when Locked, then one of the entry points

(hood, trunk, doors) has been left opened. Closing the hood, trunk, or doors

will correct the problem and you do not need to disarm the system to make

the correction. If the siren "chirped" three times, sometime after arming,

the exclusive delayed dome light learn circuit has been programmed and

the system detected a open entry point after the learned delay expired.

Again, closing the hood, trunk, or doors will correct the problem and you

do not need to disarm the system to make the correction.

ARMING THE SYSTEM: (PASSIVE)

1. Turn off the engine, exit the vehicle, close and lock all doors, hood and trunk.

2. The dash mounted LED will begin to ash rapidly, indicating that the system

is automatically (passive) arming. As an added convenience, the automatic

passive arming will not begin until all doors and trunk lid are closed, allowing

passengers to exit the vehicle at their convenience.

3. In 30 seconds, you will hear a single short "chirp" from the siren and the

vehicle's parking lamps will ash one time, indicating the system is ARMED.

At this time, the dash mounted LED will begin to ash slowly, providing a visual

indication that the system is fully ARMED.

OPTION NOTE: If the optional (not included) power door lock interface has been

installed, the alarm control module can be programmed to:

a) Automatically lock the doors during step 3 above, or

b) Lock the doors only when the transmitter is operated

4. If you wish to arm the system immediately, simply press and release the

ARMING button on the keychain transmitter. The siren will "chirp" once, the

vehicle's parking lamps will ash once, the doors will lock (optional), and the

dash mounted LED will begin to slowly ash.

128-9321

Page 4/8

Page 4

PROTECTION WHILE THE SYSTEM IS ARMED:

1. Opening any door, hood or trunk will cause the alarm to immediately sound.

The siren will continue to sound for 30 seconds, then stop and automatically

re-arm the vehicle. If the potential thief left a door opened, the siren will sound

for six 30 second cycles, then re-arm and ignore the opened door.

2. Any strong impact to the vehicle’s glass will cause the alarm to trigger for the

full 30 second alarm cycle, with "Dual Stage". Any mild impact to the vehicle's

glass or body will cause the alarm to sound a short series of warning tones.

3. Whenever the system is armed, the dash mounted LED indicator will slowly

ash. This serves as a visual deterrent to the potential thief. The LED is a very

low current bulb and will not cause the vehicle's battery to drain, even when left

unattended for extended periods.

4. Whenever the system is triggered, the vehicle's parking lights will ash for the

30 second alarm cycle, attracting added visual attention to the vehicle.

5. Whenever the system is armed, the vehicle's starter will be bypassed. If a thief

should choose to ignore the siren, the vehicle can not be started.

DISARMING THE SYSTEM:

1. As you approach the vehicle, press and release the Unlock button on the

keychain transmitter.

2. The siren will "chirp" 2 times and the vehicle's parking lamps will ash two times.

3a. ACTIVE: The dash mounted LED will turn off, and remain off until the system

is re-armed.

3b. PASSIVE: Never attempt to disarm the system from a distance that prevents

you from opening a door within 30 seconds. Since the system is programmed for

passive arming, it will begin to re-arm until a door is opened. Opening the door

will suspend the passive arming cycle.

INTRUSION WARNING SIGNALS:

The system will inform you if an intrusion attempt has occurred while you were

away from the vehicle. If an intrusion attempt has occurred, the siren will "chirp" 4

times when disarming the system.

The vehicle's parking lights will also ash 3 times to indicate an intrusion has oc-

curred. Enter the vehicle and observe the dash mounted LED for further information.

1. If the LED is ashing one time... pause...one time... etc., then an intrusion attempt

was made to a light activated entry point, or the shock sensor was activated.

128-9321

Page 5/8

Page 5

2. If the LED is ashing two times...pause...two times...etc., then an intrusion

attempt was made to the hood, trunk, or an optional sensor that has been

connected to zone 2.

3. If the LED is ashing three times...pause...three times...etc., then an intrusion

attempt was made through one of the vehicle's doors.

These intrusion warning indicators are stored in the system's memory and will only

be erased from memory when the ignition key is turned on.

Push-Button LED Valet / SYSTEM OVERRIDE Switch:

The "Valet" switch allows you to temporarily bypass all alarm functions, eliminating

the need to hand your transmitter to parking attendants or garage mechanics.

When the system is in valet mode, all alarm functions are bypassed, however, the

remote panic feature and remote door locks (optional) will remain operational. To

use the valet mode;

1. Enter the vehicle and turn the ignition key to the "on" position.

2. Press and hold the LED valet push-button switch for 5 seconds until the LED

turns on solid. The LED will remain on as long as the system is in the valet mode.

3. To return to normal operation, with the ignition switch on, press and release the

LED valet push-button switch one time. The LED will turn off indicating the unit

has been returned to the normal mode of operation.

In the event you lose your keychain transmitter, or if the transmitter fails to disarm

the system, the valet switch can be used as a system override switch.

Open the car door (the alarm will sound). Turn the ignition key on, and press and

hold the LED valet switch on. The alarm will stop sounding, and the vehicle can

now be started.

NOTE: Always remember to exit Valet Mode to ensure that the vehicle remains

protected at all times.

ELIMINATING THE ARM / DISARM CHIRPS:

The normal arming and disarming conrmation "chirps" can easily be turned on

and off using the valet push-button switch. To do this...

1. Turn the ignition key on, and then off.

128-9321

Page 6/8

Page 6

2. Within 10 seconds of turning the ignition key off, press and release the LED valet

push-button switch three times.

3a. If, before proceeding with step 2, the chirps were on, then you will hear 2 chirps

to indicate that the chirps have been turned off.

3b. If, before proceeding with step 2, the chirps were off, then you will hear 1 chirp

to indicate that the chirps have been turned on.

NOTE: Whenever the chirps are by-passed, the 3 chirp defect and 4 chirp in-

trusion indicator will always operate. This feature will always warn you if

there is a defective sensor during the arming sequence or if the vehicle

had been tampered with in your absence, even if the normal arming and

disarming chirps have been turn off.

REMOTE PANIC OPERATION:

The Lock and Unlock buttons on your keychain transmitter also functions as a

"panic" switch for instant activation of the alarm in emergency situations. To use

the remote panic switch;

1. Press and hold the arming button on the keychain transmitter for 3 seconds or

more. The alarm will immediately sound.

2. To stop the alarm, press and release the Trunk/Key button on the keychain

transmitter. If the button is not pressed, the alarm will automatically stop after

30 seconds.

TRUNK RELEASE:

This security system has an additional feature that can be wired to a number of dif-

ferent optional accessories. Some of the more common uses for this "channel" are:

 Remote Trunk Release - available for any vehicle with factory installed electronic

push-button trunk release.

 Remote Car Starter - available for most automatic transmission, fuel injected

vehicles.

 Remote Window Roll Up - available for most vehicles equipped with power

windows.

TO ACTIVATE THIS OPTIONAL ACCESSORY

Press and hold the Trunk/Key button on the keychain transmitter for approximately 3

seconds. If the system has been programmed differently by your installation center,

this output may be accessed by pressing buttons 1&2 simultaneously for 3 seconds.

NOTE: This feature will not operate when the vehicle's ignition key is turned "ON".

128-9321

Page 7/8

Page 7

PROGRAMMING NEW OR REPLACEMENT TRANSMITTERS

(BANK 1)

Transmitter Model Name, 143BP Is Also Found On Back Of

Transmitter Case (Battery Use CR2032)

1) Turn the ignition key to the on position.

2) Press and release the valet/programming switch 3 times (Siren Chirps)

3) Press the Lock Button of each transmitter you want programmed until you hear

a chirp from the horn or siren.

4) Press the valet/program button to advance to the unlock channel two, (siren

chirps)

5) Press the Unlock button of each transmitter you want to operate the unlock

function until you hear a chirp from the horn or siren.

6) Press the valet/program button to advance to the trunk release channel three,

(siren chirps).

7) Press the trunk button of each transmitter you want to operate the trunk release

feature. until you hear a chirp from the horn or siren.

8) Turn the ignition switch off.

The above action programs the Lock, Unlock, & optional Trunk Release,

This remote has the ability to operate 2 similar alarms from a single transmitter.

To toggle on and off vehicle one or two,,,

Press the Trunk/Key button + the Lock button for 5 seconds.

The LED ashes 2 times. Release the buttons, to select 2nd vehicle mode.Program

this transmitter into the second vehicle's system. Any time you are in 2nd vehicle

when the transmitter is operated, the LED will ash twice for each function. When

in in the prime vehicle mode, the LED will ash once for each function.

Transmitter Battery Replacement:

1) Locate and remove the "00" point Philips head screw on the back of the

transmitter case.

2) Carefully separate the front case from the rear.

3) Slide the CR2032 battery out from under the battery clip and dispose of

properly.

4) Install the new battery with the (+) side facing up away from the circuit board.

5) Close the case and reassemble in reverse of disassembly.

128-9321

Page 8/8

Page 8

APS-25E

SYSTEM FUNCTIONS AT A GLANCE

DASH LED INDICATORS

RAPID FLASHING .............................................. PASSIVE ARMING

SLOW FLASHING.............................................. ARMED

OFF .................................................................... DISARMED

ON - SOLID........................................................ VALET MODE

3 FLASH ... PAUSE............................................ INTRUSION ZONE 3

2 FLASH ... PAUSE............................................ INTRUSION ZONE 2

**1 FLASH ... PAUSE ............................................ INTRUSION ZONE 1

SIREN CHIRP INDICATORS

*1 CHIRP..............................................................ARM

*2 CHIRPS ...........................................................DISARM

3 CHIRPS...........................................................ARM / ZONE ACTIVE

4 CHIRPS...........................................................DISARM / INTRUSION

PARKING LAMPS (Optional)

1 FLASH.............................................................ARM

2 FLASH.............................................................DISARM

3 FLASH.............................................................DISARM / INTRUSION

** Where applicable.

*These chirps are optional and may be disengaged.

To purchase replacement transmitters

or to get additional product information go to:

www.prestigecarsecurity.com

Optional Channel 2 Device

Your System Has These Features Activated:

Starter Cut-out

Door Lock Interface

Shock Detector



Motion Detector

Hardwire



Inhaltsverzeichnis

Andere Prestige Autoalarmanlage Handbücher

Prestige

Prestige PE1BZ Bedienungsanleitung

Prestige

Prestige Platinum+ APS-596 Bedienungsanleitung

Prestige

Prestige 1286458 Bedienungsanleitung

Prestige

Prestige APS596Z Bedienungsanleitung

Prestige

Prestige APS-520 Bedienungsanleitung

Prestige

Prestige Owner's Manual Bedienungsanleitung

Prestige

Prestige APS-20B Bedienungsanleitung

Prestige

Prestige Platinum APS 996 Bedienungsanleitung

Prestige

Prestige 1286795 Bedienungsanleitung

Prestige

Prestige 1286520 Bedienungsanleitung

Prestige

Prestige Prestige 128-4243B Bedienungsanleitung

Prestige

Prestige Prestige 128-7853 Bedienungsanleitung

Prestige

Prestige APS-25HJ Bedienungsanleitung

Prestige

Prestige Platinum APS 500 Bedienungsanleitung

Prestige

Prestige APS-43HJ Bedienungsanleitung

Prestige

Prestige Prestige 128-4246A Bedienungsanleitung

Prestige

Prestige Prestige Platinum 128-8122 Bedienungsanleitung

Prestige

Prestige Prestige Platinum 128-8128 Bedienungsanleitung

Prestige

Prestige Platinum APS-787C Bedienungsanleitung

Prestige

Prestige 5WTX Betriebsanleitung

Prestige

Prestige APS-20B Bedienungsanleitung

Prestige

Prestige Prestige Platinum APS 600 Bedienungsanleitung

Prestige

Prestige APS-787E Bedienungsanleitung

Prestige

Prestige APS-997E Bedienungsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken

Clifford

Clifford 3606X Bedienungsanleitung

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum+ APS-511C Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Viper

Viper 4708V Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Audiovox

Audiovox Auto Security XR91 Betriebsanleitung

Clifford

Clifford Sabre II Bedienungsanleitung

CrimeStopper

CrimeStopper CS-8717 Kurzanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Clifford

Clifford CYBER 2 Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung

Clifford

Clifford Nova 3 Bedienungsanleitung

Viper

Viper 560XV Bedienungsanleitung