Prestige PE1BZ Bedienungsanleitung

Owner’s Guide

For Models:

PE1BZ

PE1BZLR

IMPORTANT NOTE: The operation of the Security and Convenience System as described in this manual is

applicable to most vehicles. However, due to the conguration of some vehicles, some functions AND/OR

SAFETY PRECAUTIONS may not apply. Please see your installing dealer for more information.

APSSEC

RF Upgrade Kit

2APSSEC PE1BZ_PE1BZLR Owners revA

Table of Contents

Using Your Remote Control.................................................................... 3

Arming the Security System .............................................................. 3

Disarming the Security System ......................................................... 3

Two Stage Door Unlock (optional)..................................................... 3

Bypassing the Shock Sensor ............................................................ 3

Alarm City Mode................................................................................ 4

User Selectable Notication Chirps................................................... 4

User Selectable LED ......................................................................... 4

Programmed Transmitter Notication................................................ 4

Valet Mode ........................................................................................ 5

Manually Overriding the Security System ......................................... 5

Status LED, Light Flashes and Siren/Horn Indications ....................... 7

Replacing Remote Control Batteries..................................................... 9

Warranty Information ............................................................................ 10

Arming the Security System

To arm the system, exit the vehicle, close all doors, then press the button. The

parking lights will ash 1 time, indicating the system is armed, has locked the doors

(if equipped and connected) and activated the starter disable feature. The LED status

indicator will blink steadily, once per second.

NOTE: The system is equipped with a feature called Silent Choice. If enabled,

the system requires a second press of the button to activate an audible arming

response from the vehicle.

*Throughout this manual, ‘press’ refers to pressing for less than 1 second; ‘press and hold’ refers to pressing for more

than 3 seconds.

Using Your Remote Control

Two Stage Door Unlock (Optional)

If this feature is enabled on your system, pressing the button 2 times will unlock

only the driver’s door. Press 2 times again within three seconds to unlock the

remaining doors.

Disarming the Security System

To disarm the system press the button 2 times. The parking lights will ash 1

time, indicating the system is disarmed and has unlocked the doors (if equipped and

connected).

NOTE: The system is equipped with a feature called Silent Choice. If enabled,

the system requires a second double press of the button to activate an audible

disarming response from the vehicle. If your system is set up for 2 step unlock, a third

press of unlock will activate the audible response.

Bypassing The Shock Sensor

The included security shock sensor has two stages of detection, Warn-Away and Full

Trigger. To arm the system and shock sensor press the button. The system will

beep and the lights wil ash 1 time.

To Arm the system and bypass the Warn-Away detection stage press the button 2

times within 5 seconds.

To Arm the Alarm the bypass both detection stages press the button 3 times within

5 seconds.

4APSSEC PE1BZ_PE1BZLR Owners revA

Programmed Transmitter Notication

As a security precaution each time the vehicle’s ignition is turn on the status LED

light with ash the number of transmitters programmed into the system. This helps

to identify unauthorized transmitters from accessing your vehicle. If you believe an

unauthorized transmitter has been programmed to your system, contact your installing

dealer for assistance.

User Selectable Notication Chirps

System ARM/DISARM chirps can be toggled ON or OFF without entering the

programming feature banks.

1. Turn the ignition ON then OFF.

2. Press and release the valet/programming button 3 times. The system

will respond with 1 chirp for ON or 2 chirps for OFF.

User Selectable LED

This feature will control whether the LED is ON or OFF when the system is Armed/

Locked and can be toggled ON or OFF without entering the programming feature

banks.

1. Turn the ignition ON, OFF, ON, OFF.

2. Press and hold the valet/programming button for 5 seconds. The system

LED will respond with 1 ash for ON or 2 ashes for OFF.

City Mode

City Mode allows the user to change the sound of the alarm system to make it easily

identied when the alarm is trigger. To enter City Mode press the button 4 times

within 10 seconds.

Valet Mode

When valet mode is activated the status LED will light solid, and all security and

remote start functions will be disabled. To enter or exit valet mode simply follow the

steps outlined below:

1. Turn the vehicle’s ignition ON.

2. Push and hold the programming/valet button.

3. The LED will turn on solid when valet mode is active

4. Release the programming/valet button.

Manually Overriding the Security System

Your system can be disarmed without the use of the transmitter. This is necessary to

operate your vehicle if the transmitter is lost or its battery fails. To by-pass the alarm

system;

1. Open the vehicle door. The alarm will sound.

2. Turn the ignition key to the ON position.

3. Within 10 seconds, press and release the valet push button switch.

The alarm system will stop sounding and enter the (by-passed) mode. You can now

start and operate the vehicle normally.

Stand Alone Valet Override (Optional)

Your system can be disarmed without the use of the transmitter or valet button. This

is necessary, since you will need the ability to operate your vehicle if the transmitter

is lost or its battery fails. To by-pass the alarm system;

1. Open the vehicle door. The alarm will sound.

2. Cycle the ignition key ON, OFF, ON.

3. Within 10 seconds, press and release the Brake pedal 3 times.

The alarm system will stop sounding and enter the (by-passed) mode. You can now

start and operate the vehicle normally. This feature must be programmed ON by an

autorized dealer.

6APSSEC PE1BZ_PE1BZLR Owners revA

Custom Code Valet Override (Optional)

Unlike the default Valet Override, Custom Code Override is a user personalized

code that o󰀨ers a higher lever of security. If the user chooses to use Custom Code

Override, Feature Bank 2 ; Feature 9 must be programmed for “Custom Code”. Once

the option has been selected the code must be programmed. Once the Custom Code

is programmed it cannot be changed without rst disarming the alarm.

Custom Code Override Procedure

The Custom Code is made up of 2 numbers. Each chosen number must be between

digits 1-9. The default Custom Code is “11”. To disarm the alarm using the Custom

Code option:

1. Turn the vehicle ignition to ON.

2. Within 5sec, Press the valet button 1x.

3. Within 5sec, Turn the ignition OFF/ON.

4. Within 5sec, Press the valet button 1x.

5. Turn the vehicle ignition to OFF then ON to start the vehicle.

Custom Code Programming Procedure

In this example, the user has selected Custom Code “23”. To program a user

selected custom code:

Start with the alarm disarmed.

1. Turn the ignition to the ON position

2. Within 10sec, press the valet button 3x to enter programming.

3. Within 10sec, Cycle the ignition OFF/ON, OFF/ON, OFF/ON. The system will

beep 1x.

4. Within 10sec, Press the valet button 2x. This number will indicate the rst digit

of the chosen Custom Code.

5. Within 10sec, Cycle the ignition OFF/ON.

6. Within 10sec, Press the valet button 3x. This number will indicate the second

digit of the chosen Custom Code.

7. Cycle the ignition OFF.

If the Custom Code was accepted the LED will ash the rst number (2), pause, then

the second number (3). This will repeat 2 more times to conrm the Custom Code

entry. If after 15sec the LED does not ash please repeat steps 1-7.

Status LED, Light Flashes, and Siren/Horn Indications

Status LED Flash Indications

LED Flashes Function

OFF Disarmed

Slow Flash Armed

Fast Flash Passive Arming Countdown

ON (Solid) Valet Mode

1 Flash / Disarmed Zone 1 Trigger, Shock Sensor

2 Flashes / Disarmed Zone 2 Trigger, Trunk / Hood

3 Flashes / Disarmed Zone 3 Trigger, Door

Siren/Horn Chirp Indications

Chirps Function

1 Arm

2 Disarm

3 Door Ajar Upon Arming

4 Disarm / Triggered

Parking Light Flash Indications

Flashes Function

1 Arm

2 Disarm

3 Disarm / Triggered

8APSSEC PE1BZ_PE1BZLR Owners revA

Replacing Remote Control Batteries

1 Button Remote Control - Model 181BP / 181SP

The CR2032 battery inside each remote control should last approximately 1 year under

normal use. When the batteries become weak you will notice the remote control range

(the distance from the vehicle the remote control will work) deteriorate and the small LED

on the remote control will dim. To replace the remote control batteries:

1. Using a coin, disassemble the halves of the remote

control.

2. Remove the old battery, observing the +/- symbols on the

batteries and replace with a new battery.

3. Reassemble the halves of the remote control

4. Test operation of the remote control.

LIMITED LIFETIME WARRANTY

Applies to Prestige Series Control Modules, Sirens, Sensors, and Relays.

Voxx Electronics Corporation (the Company) warrants to the original purchaser of this

product that should this product or any part thereof, (other than transmitters) under nor-

mal use and conditions, be proven defective in material or workmanship during the life-

time of the vehicle, in which it was originally installed from the date of original purchase

such defect(s) will be repaired or replaced with new or reconditioned product, (at the

Company’s option) without charge for parts or repair labor. A transmitter is warranted for

12 months from the date of original purchase.

To obtain repair or replacement within the terms of this Warranty, the product is to

be delivered with proof of warranty coverage (e.g. dated bill of sale), specication of

defect(s), transportation prepaid, to an approved warranty station. This Warranty is not

transferable.

This Warranty does not cover damage to the vehicle’s electrical system or costs

incurred for removal or reinstallation of the product. This Warranty does not cover bat-

teries, broken LCD or OLED display screens, nor apply to any product or part thereof

which, in the opinion of the Company, has su󰀨ered or been damaged through alteration,

improper installation, mishandling, misuse, abuse, neglect, accident, or by removal or

defacement of the factory serial number/bar code label(s).

This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED WAR-

RANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, SHALL

BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. IN NO CASE

SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL

DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY. No person or rep-

resentative is authorized to assume for the Company any liability other than expressed

herein in connection with the sale of this product.

The company does not warrant that this product cannot be compromised or circum-

vented. THE EXTENT OF THE COMPANY’S LIABILITY UNDER THIS WARRANTY

IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND, IN NO

EVENT, SHALL THE COMPANY’S LIABILITY EXCEED THE PURCHASE PRICE PAID

BY PURCHASER FOR THE PRODUCT WITHOUT COST OF INSTALLATION.

Some states do not allow limitations on how long an implied warranty lasts or the

exclusion or limitation of incidental or consequential damage so the above limitations or

exclusions may not apply to you. This Warranty gives you specic legal rights and you

may also have other rights which vary from state to state.

Voxx Electronics Corporation, 180 Marcus Blvd., Hauppauge, New York 11788 / 1-800-645-4994

10 APSSEC PE1BZ_PE1BZLR Owners revA

Voxx Electronics Corporation.

Customer Service 1-800-225-6074

WWW.ADVENTPRODUCTS.COM

FCC COMPLIANCE

This device complies with Part 15 of the FCC rules and with RSS-210 of

Industry Canada. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including any interference that

may cause undesired operation.

Warning!

Changes or modications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

PATENTED: www.voxxintl.com/company/patents

Andere Handbücher für PE1BZ

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Prestige Autoalarmanlage Handbücher

Prestige

Prestige APS 800a Bedienungsanleitung

Prestige

Prestige Prestige 128-4243B Bedienungsanleitung

Prestige

Prestige APS-20B Bedienungsanleitung

Prestige

Prestige APS-20B Bedienungsanleitung

Prestige

Prestige Platinum APS 996 Bedienungsanleitung

Prestige

Prestige APS-596E Bedienungsanleitung

Prestige

Prestige 1286469 Bedienungsanleitung

Prestige

Prestige Prestige Platinum 128-7401A Bedienungsanleitung

Prestige

Prestige Prestige 128-4864 Bedienungsanleitung

Prestige

Prestige APS510Z Bedienungsanleitung

Prestige

Prestige 1286795 Bedienungsanleitung

Prestige

Prestige Owner's Manual Bedienungsanleitung

Prestige

Prestige APS-995 Bedienungsanleitung

Prestige

Prestige APS-43HJ Bedienungsanleitung

Prestige

Prestige Prestige 128-4246A Bedienungsanleitung

Prestige

Prestige APS-997E Bedienungsanleitung

Prestige

Prestige 1287181 Bedienungsanleitung

Prestige

Prestige 5WTX Betriebsanleitung

Prestige

Prestige APS-20B Bedienungsanleitung

Prestige

Prestige APS-OE2B Betriebsanleitung

Prestige

Prestige Prestige Platinum APS 600 Bedienungsanleitung

Prestige

Prestige Platinum APS 500 Bedienungsanleitung

Prestige

Prestige Prestige Platinum 128-8128 Bedienungsanleitung

Prestige

Prestige APS-520 Bedienungsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken

Clifford

Clifford 3606X Bedienungsanleitung

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum+ APS-511C Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Viper

Viper 4708V Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Audiovox

Audiovox Auto Security XR91 Betriebsanleitung

Clifford

Clifford Sabre II Bedienungsanleitung

CrimeStopper

CrimeStopper CS-8717 Kurzanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Clifford

Clifford CYBER 2 Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung

Clifford

Clifford Nova 3 Bedienungsanleitung

Viper

Viper 560XV Bedienungsanleitung