Pro-face GP37W2-BG41-24V Bedienungsanleitung

• When connecting the

GP37W2-BG41-24V(hereafter referred to as the

"GP")'s

power cord terminals to the power terminal block, check first

that the GP power supply is completely turned OFF, via a breaker, or

similar unit.

• Do not use power beyond the GP's specified voltage range. Doing so

may cause a fire or an electric shock.

• Do not modify the GP's design, since it may lead to a fire or an electric

shock.

• Do not use the GP in an environment where flammable gases are

present, since operating the GP may cause an explosion.

• If the GP's lithium battery*1 is incorrectly replaced (i.e. its + and – sides

are reversed), it may explode. Therefore, please contact your local GP

distributor prior to changing the battery.

• Do not use GP touch panel switches in life-threatening or important

disaster prevention situations. For safety related switches, such as

an emergency stop switch, be sure to use a separate mechanical switch.

• To prevent operator injury or machine damage, be sure to design your

system so that machinery will not malfunction due to a communication

fault between the GP and its host controller.

• The GP is not appropriate for use with aircraft control devices, aerospace

equipment, central trunk data trans-mission (communication) devices,

nuclear power control devices, or medical life support equipment, due to

these devices inherent requirements of extremely high levels of safety

and reliability.

• When using the GP with transportation vehicles (trains, cars and ships),

disaster and crime prevention devices, various types of safety equipment,

non-life support re-lated medical devices, etc. redundant and/or failsafe

sys-tem designs should be used to ensure the proper degree of reliability

and safety.

GP Usage Cautions

•To prevent touch panel damage, do not strike the panel face with a

hard or heavy object, or push hard on the panel face.

•Do not install the GP where the temperature will exceed its specified range.

•Do not allow water, liquids or metal particles to enter the GP. Any of

these can lead to a malfunction or short circuit.

•Avoid installing the GP where sudden, large changes in temperature

may occur. These changes may cause condensation to form inside

the unit, possibly causing the GP to malfunction.

•Do not install the GP where its ventilation holes may be blocked. If

these holes are blocked, excessive heat will build up inside the GP.

• Do not install or store the GP :

- Where high levels of dust exist or in direct sunlight.

- Where either strong shocks or excessive vibration may occur.

- Where chemicals or chemical fumes are present.

- Near high temperature equipment.

•Do not use paint thinner or organic solvents to clean the GP's case or

screen.

•Be sure to back up all GP data regularly.

•After turning the GP OFF, be sure to wait a few seconds before turning

it ON again. If the GP is re-started too quickly, it may not start up cor-

rectly.

WARNINGS

*1 This mark is applicable only in Taiwan.

UL/c-UL (CSA) Application Notes

The GP37W2-BG41-24V is a UL/c-UL (CSA) recognized product. (UL File No.

E177793.)

This unit conforms as a component to the following standards:



UL 1950, Third Edition, dated July 26,1995

(Standard for Safety of Information Technology Equipment, including Electrical Business

Equipment)



CAN/CSA-C22.2, No.950-95

(Standard for Safety of Information Technology Equipment, including Electrical Business

Equipment)

GP37W2-BG41-24V (UL Registration Model: 2880052-01)

• The GP-37W2B must be used as a built-in component of an end-use product.

• Machinery which has a GP-37W2B installed in it requires UL/c-UL inspection for the

combination of this unit and the machinery.

• If the GP-37W2B is mounted so as to cool itself naturally, be sure to install it in a

vertical panel. Also, be sure the unit is installed so that it is at least 100mm (3.94 in.)

away from any adjacent structures or devices. If these requirements are not met, the

heat generated by the GP’s internal components may cause the unit to fail to meet UL/

c-UL standard requirements.

The GP37W2-BG41-24V is CE marked products that conform to EMC directives

EN55011 class A and EN50082-2.

For detailed CE marking information, please contact your local GP distributor.

CE Marking

CNS Application Notes

The GP37W2-BG41-24V complies with the following CNS recognized standard.



CNS 13438 (Class A device)

The GP is an Industrial Device (Class A Device). Use of this device in a home may cause

radio wave interference with nearby devices. If interference does occur, please try a variety of

countermeasures to solve the problem.

Package Contents

The following items are included in the GP's package. Before using the GP, please

confirm that all items shown here are present.

This unit has been carefully packed, with special attention to quality. However, should you

find anything damaged or missing, please contact your local GP distributor immediately.



GP Unit (1)

(GP37W2-BG41-24V )



Installation Fasteners (4)



Installation Guide (1)

Installation

Guide

GP Options (Made by Digital)

GP37W2-MM01-ENG (English)

GP37W2-MM01 (Japanese)

For more information about these optional items, please refer to individual GP cata-

logues.



Cables



Adapters



Screen editor software, etc.



GP-37W2 User Manual

(sold separately)

Digital

GP-37W2

User Manual

DIGITAL ELECTRONICS CORP.

Revision Information

Revision information can be found on your GP unit’s rear-face Pro-face label. The bot-

tom-most [REV] row’s asterisk (*) mark indicates the Revision character.

In the example shown below, the asterisk indicates that this unit’s Revision character is

“D”.

1 Parts Names and Functions

Unit: mm (in.)

Front View Side View

A: Display

Displays User-created screens and host

(PLC) data. GP37W2-BG41-24V Blue

mode LCD

B: Touch Panel

Performs screen change operations and

sends data to the host (PLC).

C: Power Lamp

Lights when the power cord is connected.

(Green LED)

D: Power Input Terminal Block

Connects the GP power cable's input and

ground wires to the GP.

E. Serial Interface

Connects an RS-232C or RS-422 (Serial)

cable (from the host/PLC) to the GP.

F: Tool Connector

Connects the Data Transfer Cable, or a Bar

Code Reader to the GP.

A,B

Top View

2 Dimensions

3 Serial Interface

This interface is used to connect the GP to the host (PLC), via either an RS-232C or

RS-422 cable.

Recommended Connector: Dsub 25 pin plug XM2A-2501<made by OMRON Corp.>

Recommended Cover: Dsub 25 pin Cover XM2S-2511<made by OMRON Corp.>

Jack Screw XM2Z-0071<made by OMRON Corp.>

Use rough metric type M2.6 x 0.45p threads to hold the cable's set (fastening)

screws in place.

RecommendedCable:CO-MA-VV-SB5Px28AWG<madebyHITACHICable>

25 13

14 1

Pin #

SignalName

Meaning

Frame Ground

SIO

Send Data (RS-232C)

ReceiveData (RS-232C)

Request to Send (RS-232C)

Clear to Send (RS-232C)

No Connection

SignalGround

Carrier Detect(RS-232C)

TRMX

Termination (RS-422)

RDA

Receive Data A (RS-422)

SDA

Send Data A (RS-422)

No Connection

VCC

5V Output0.25A

SDB

Send Data B (RS-422)

RDB

Receive Data B (RS-422)

No Connection

CSB

Clearto Send B(RS-422)

ERB

Enable Receive B (RS-422)

Enable Receive (RS-232C)

CSA

Clearto Send A(RS-422)

ERA

Enable Receive A (RS-422)

BUZZGND

ExternalBuzzerGround

No Connection

25 BUZZ OUT ExternalBuzzerOutput

• The GP’s RS-485(RS-422) port is not isolated, therefore, be sure

to connect pin #7 (SG terminal) to the other unit's signal

ground terminal. If this is not done, the RS-485(RS-422) circuit

may be damaged.

• Since pin #14 (VCC) is not protected, be sure to use it only

within its rated range.

When making a cable, please be aware of the following:

• Do not connect #9 (TRMX), #10 (RDA), #11 (SDA), #15 (SDB), #16 (RDB),

#18(CSB), #19 (ERB), #21 (CSA), and #22 (ERA).

• The following pairs of pin numbers must be connected (shorted):

#18(CSB) <-> #19 (ERB)

#21(CSA) <-> #22 (ERA)

• Connecting the #9 (TRMX) and #10 (RDA) wires adds a termination resistance of

100ΩΩ

ΩΩ

Ωbetween RDA and RDB.

• Use a 4-wire cable when the PLC type is Memory Link and the cable is RS-422.

• Use pins 23(BUZZ GND) and 25(BUZZ OUT) when producing external output for

an alarm.

This output circuit does not contain fuses. If used, Pro-face recommends the design

of an external safety circuit. (GP units Revision P or later)

To confirm your GP unit’s Revision, refer to "Revision Information".

External Buzzer Output Buzzer Can drive a buzzer

of DC5V to

DC24V, at up to

0.3A.

Internal

Circuit

SIO 25 Pin

SIO 23 Pin

GP-37WB Unit

Optical Isolation



Confirm the Installation Gasket's Positioning

It is strongly recommended that you use the gasket since it absorbs vibration in addi-

tion to repelling water.

Prior to installing the GP in its metal panel, place the unit on a level

surface with the display panel facing downward and check that the

installation gasket is securely attached to the back of the unit.

Tightening the fastener screws with too much force can damage the

GP's case. The torque necessary to ensure a sufficient seal is 0.5 to

0.6N•m.



Cut a hole in the metal panel according to the dimensions given below

Insert the GP into the panel from the front of the panel.

Unit: mm (in.)

4 Installation



Attach the GP's Installation Fasteners from inside the panel

The following figures show the four (4) insertion slot locations of the fasteners. Insert

each fastener's hook into the slot and tighten it with a screwdriver.

Gasket

Rear of GP

under 4-R2Panel thickness should be from

1.6mm (0.06in.) to 5.0mm (0.2in.).

GP Unit

Installation

Fastener

(7.54 )

+0.04

-0

191.5 +1

- 0

141.5 +1

- 0

(5.57 )

+0.04

-0

5 Wiring

*1 Suggested Ring Terminal: V2-MS3 (made by JST Co.)

• When connecting a wire to the GP's FG terminal, be sure the wire

is grounded. Not grounding the wire will result in excessive

noise.

• To avoid a short caused by loose ring terminals, be sure to use

ring terminals with an insulating sleeve.

• Wherever possible, use thick wires (max. 2 mm2) for power terminals, and twist

the wire ends before attaching the ring terminals.

• Be sure to use the following size ring terminals.*1

Under

6.0mm (0.24in.)

Over φφ

φφ

φ 3.2mm (0.13in.)

Rear of GP Ring Terminals*1

Power Input

Terminal Block + - FG

• To avoid an electric shock, check first that the GP's power

supply is completely turned OFF, via a breaker, or similar unit

when connecting the GP power cord terminals to the power

terminal block.

• GP-37W2B Series units are designed to use only DC24V in-

put. Any other power level can damage both the GP and the

power supply.

• The GP-37W2B is not equipped with a power switch, there-

fore, you need to use a breaker switch.

WARNINGS

When attaching a wire to the GP's rear face FG terminal, (on the Power Input Terminal

Block), be sure to create an exclusive ground.*1

6Grounding Precaution

7Input/Output Signal Line Precautions



Connecting the GP's Power Cord

When connecting the power cord, be sure to follow the procedures given below.

1. Confirm that the GP's Power Cord is unplugged from the power supply.

2. Use a screwdriver to remove the Power Input Terminal Block's clear plastic cover.

3. Unscrew the screws from the middle three (3) terminals, align the Ring Terminals and

reattach the screws.

4. Confirm that the wires are connected correctly.

5. Replace the Power Input Terminal Block's clear plastic cover.

The torque required for fastening the screws is 0.5 to 0.6N•m.

8Maintenance and Inspection

When the surface or the frame of the display gets dirty, soak a soft cloth in water with

a neutral detergent, wring the cloth tightly, and wipe the display.

• Do not use paint thinner, organic solvents, or strong acid compound to

clean the unit.

• Do not use hard or pointed objects to operate the touch-screen panel,

since it can damage the panel surface.

*1 Use a grounding resistance of 100

Ω

, a wire of 2mm2or thicker, or your country's

applicable standard.

•All GP Input and Output signal lines must be separated from all operating circuit

(power) cables.

•If this is not possible, use a shielded cable and ground the shield.

Inhaltsverzeichnis

Andere Pro-face Touchscreen Handbücher

Pro-face

Pro-face PS300-BU00 Stücklistenhandbuch

Pro-face

Pro-face GP-4400 Series Bedienungsanleitung

Pro-face

Pro-face LogiTouch GLC150-BG41-RSFL-24V Bedienungsanleitung

Pro-face

Pro-face PS-3700A Bedienungsanleitung

Pro-face

Pro-face PS-3710A Series Bedienungsanleitung

Pro-face

Pro-face GP-2400 Series Bedienungsanleitung

Pro-face

Pro-face PL-5900 Series Bedienungsanleitung

Pro-face

Pro-face PS-G Bedienungsanleitung

Pro-face

Pro-face GP4000 SERIES Bedienungsanleitung

Pro-face

Pro-face PS-4700 Series Bedienungsanleitung

Pro-face

Pro-face SP5000 Series Bedienungsanleitung

Pro-face

Pro-face GP-3400 Series Bedienungsanleitung

Pro-face

Pro-face GP-2500 Series Bedienungsanleitung

Pro-face

Pro-face GP4104G1D Bedienungsanleitung

Pro-face

Pro-face PS-A Series Bedienungsanleitung

Pro-face

Pro-face GP3000 Series Bedienungsanleitung

Pro-face

Pro-face GP377-LG Series Stücklistenhandbuch

Pro-face

Pro-face GP-3310T Stücklistenhandbuch

Pro-face

Pro-face PS-4700 Series Bedienungsanleitung

Pro-face

Pro-face AGP3200-A1-D24 Bedienungsanleitung

Pro-face

Pro-face FP-3710K Series Bedienungsanleitung

Pro-face

Pro-face PS-3600G Series Bedienungsanleitung

Pro-face

Pro-face GP3000 Series Bedienungsanleitung

Pro-face

Pro-face PL-6920 Series Bedienungsanleitung

Beliebte Touchscreen Handbücher anderer Marken

FlowLine

FlowLine Data loop Bedienungsanleitung

ALPEX

ALPEX AEx-8 P Series Bedienungsanleitung

Ltech

Ltech E5S Bedienungsanleitung

Harman

Harman AMX MODERO S MSD-701-L2 Bedienungsanleitung

Acnodes

Acnodes PC 1150 Bedienungsanleitung

AIS

AIS IP10IA99 series Bedienungsanleitung

IBASE Technology

IBASE Technology ASTUT-152-RE1S Bedienungsanleitung

YASKAWA

YASKAWA TP 610C Bedienungsanleitung

B&R

B&R Power Panel C Series Bedienungsanleitung

Beijer Electronics

Beijer Electronics X2 control Bedienungsanleitung

AXIOMTEK

AXIOMTEK GOT321W-521 Bedienungsanleitung

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Bedienungsanleitung

Qomo

Qomo QIT1386 Bedienungsanleitung

DFI

DFI KS104-CD Bedienungsanleitung

AMX

AMX AXP-PPC Leitfaden

Sartorius

Sartorius X3 PR 5410 Bedienungsanleitung

AMX

AMX Modero X Series Bedienungsanleitung

Advantech

Advantech TPC-30 Series Bedienungsanleitung