Pro-face PS-3650A Series Bedienungsanleitung

36$36$6HULHV

+DUGZDUH0DQXDO

Preface

Thank you for purchasing a Pro-face PS-3650A/PS-3651A Series Unit (Hereafter referred to as the PS-A unit).

Before operating your PS-A unit, be sure to read this manual to familiarize yourself with the PS-A unit’s operation

procedures and functions.

Product names used in this manual are the trademarks / registered trademarks of their respective owners.

NOTICE

1. Copying this manual’s contents, either in whole or in part, is prohibited without the express permission of Digital

Electronics Corporation, Japan.

2. The information contained in this manual is subject to change without notice.

3. If you find any errors or omissions in this document, please contact Digital Electronics Corporation to report your

findings.

4. Regardless of Clause 3 above, Digital Electronics Corporation shall not be held responsible for any damage,

losses or third-party damage resulting from the use of this product.

Essential Safety Precautions

All safety-related procedures stated in this document must be followed to operate the PS-A unit correctly and safely. Be

sure to read this and any related documents thoroughly to understand the correct operation and functions of the PS-A unit.

Safety Icons

Throughout this manual, these icons provide essential safety information for PS-A unit operation procedures requiring

special attention. These icons indicate the following levels of danger:

System Design

Indicates situations where severe bodily injury, death or major equipment

damage can occur.

Indicates situations where slight bodily injury or minor equipment damage can

occur.

Indicates actions or procedures that should NOT be performed.

Indicates actions or procedures that MUST be performed to ensure correct

unit operation.

Do not create PS-A unit touch panel switches that could possibly endanger the safety of personnel or

equipment. A malfunction of the PS-A unit, its I/O unit(s), cable(s), or other related equipment can cause

unexpected output signals, leading to a serious accident. Be sure to design all important machine

operation switches so they are operated via a separate control system, and not via the PS-A unit.

Do not create PS-A unit touch panel switches to control machine safety operations, such as an

emergency stop switch. Install these switches as separate hardware switches, otherwise severe bodily

injury or equipment damage can occur.

Be sure to design your system so that a communication fault between the PS-A unit and its host controller

will not cause equipment to malfunction. This is to prevent any possibility of bodily injury or equipment

damage.

Do not use the PS-A unit as a warning device for critical alarms that can cause serious operator injury,

machine damage or can halt system operation. Critical alarm indicators and their control/activator units

must be designed using stand-alone hardware and/or mechanical interlocks.

Do not use the PS-A unit with aircraft control devices, aerospace equipment, central trunk data transmis-

sion (communication) devices, nuclear power control devices, or medical life support equipment, due to

these devices’ inherent requirements of extremely high levels of safety and reliability.

Handling

Wiring

Maintenance

When using the PS-A unit with transportation vehicles (trains, cars, and ships), disaster and crime preven-

tion devices, various types of safety equipment, and medical devices that are not life-support related, use

redundant and/or failsafe system designs to ensure proper reliability and safety.

After the PS-A unit’s backlight burns out the touch panel is still active, unlike the PS-A unit’s “Standby

Mode”. If the operator fails to notice that the backlight is burned out and touches the panel, a potentially

dangerous machine operation error can occur. Therefore, do not create PS-A unit touch panel switches

that may cause injury and/or equipment damage.

If your PS-A unit’s backlight suddenly turns OFF, use the following steps to determine if the backlight is

actually burned out.

1) If the PS-A unit’s “Backlight Control” is not set and the screen has gone blank, your backlight is burned

out.

2) If the PS-A unit’s “Backlight Control” is set to Standby Mode and the screen has gone blank, and

touching the screen or performing another input operation does not cause the display to reappear, your

backlight is burned out.

Do not modify the PS-A unit. Doing so may cause a fire or an electric shock.

Do not operate the PS-A unit in an environment where flammable gases are present, since it may cause

an explosion.

To prevent an electric shock be sure to disconnect your PS-A unit’s power cord from the power supply

before wiring the PS-A unit.

Do not use voltage beyond the PS-A unit’s specified range. Doing so may cause a fire or an electric

shock.

Do not connect or disconnect Host and PS-A unit communication cables while the PS-A unit is turned ON.

The PS-A unit uses a lithium battery for backing up its internal clock data and the battery may explode if it

is replaced incorrectly. When replacement is required, use a Pro-face-designated replacement product.

SEE 4.6 Replacing the Internal Battery (page4-15)

Installation

Wiring

Maintenance

Unit Disposal

General Safety Precautions

Be sure all cable connectors are securely attached to the PS-A unit. A loose connection may cause

incorrect input or output signals.

Be sure to ground the PS-A unit’s FG wire separately from other equipment FG lines. Also, be sure to use

a grounding resistance of 100Ω or less and a 2mm2or thicker wire, or your country’s applicable standard.

Otherwise, electric shock or malfunctions may result.

Be sure to use only the designated torque to tighten the PS-A unit’s terminal block screws. If these screws

are not tightened firmly, it may cause a short-circuit, fire or incorrect unit operation.

Be sure that metal particles and wiring debris do not fall inside the PS-A unit. They can cause a fire,

malfunction or incorrect unit operation.

Do not reset or turn the PS-A unit OFF, or insert or remove the CF Card while the PS-A unit’s CF Card or

hard disk is being accessed. Otherwise, CF Card and the hard disk internal data may be damaged or lost.

When the product is disposed of, it should be disposed of in a manner appropriate to, and in accordance

with, the user country's industrial machinery disposal/recycling standards.

Do not press on the PS-A unit’s display with excessive force or with a hard object, since it can damage the

display. Also, do not press on the touch panel with a pointed object, such as the tip of a mechanical pencil

or a screwdriver, since doing so can damage the touch panel.

Do not install the PS-A unit where the ambient temperature exceeds the specified range. Doing so may

cause a unit malfunction.

To prevent abnormally high temperatures from occurring inside the PS-A unit, do not restrict or block the

PS-A unit’s rear-face ventilation slots.

Do not operate the PS-A unit in areas where large, sudden temperature changes can occur. These

changes can cause condensation to form inside the PS-A unit, possibly causing it to malfunction.

Do not allow water, liquids or metal fragments to enter inside the PS-A unit’s case, since they can cause

either a malfunction or an electric shock. For use in Pollution Degree 2 environment.

Do not operate or store the PS-A unit in locations where it can be exposed to direct sunlight, high

temperatures, excessive dust, moisture or vibration.

LCD Panel Usage Precautions

• The LCD panel’s liquid contains an irritant. If the panel is damaged and any of this liquid contacts your skin,

immediately rinse the area with running water for at least 15 minutes. If the liquid gets in your eyes, immediately rinse

your eyes with running water for at least 15 minutes and consult a doctor.

• The PS-A unit’s LCD screen may flicker or show unevenness in the brightness of certain images or at some contrast

settings. This is an LCD characteristic and not a product defect.

• Some LCD screens may have differences in brightness and tone. Please be aware of this difference when using

multiple units side by side.

• Depending on the ambient temperature, LCD screens may sometimes look whitish (at high temperatures) or blackish

(at low temperatures). This is an LCD characteristic and not a product defect.

• Some of PS-A unit’s LCD screens may contain light and dark pixels. This is an LCD characteristic and not a product

defect.

• Extended shadows, or “Crosstalk” may appear on the LCD screen. This is an LCD characteristic and not a product defect.

• The color displayed on the PS-A unit’s LCD screen may appear different when seen from outside the specified

viewing angle. This is an LCD characteristic and not a product defect.

• When the same image is displayed on the PS-A unit’s screen for a long period, an afterimage may appear when the

image is changed. This is an LCD characteristic and not a product defect.

• To prevent an afterimage:

• Set the PS-A unit’s display OFF feature when you plan to display the same screen image for a long period of time.

• Change the screen image periodically and try to not display the same image for a long period of time.

Do not operate or store the PS-A unit where chemicals evaporate, or where chemicals are present in the air.

Corrosive chemicals : Acids, alkalines, liquids containing salt

Flammable chemicals : Organic Solvents

Do not use paint thinner or organic solvents to remove dirt or oil from the PS-A unit’s surface. Instead, use

a soft cloth moistened with a diluted neutral detergent.

Do not use or store the PS-A unit in areas with direct sunlight, since the sun’s ultraviolet rays may cause

the LCD’s quality to deteriorate.

Do not store the PS-A unit in an area where the temperature is lower than that recommended in the PS-A

unit’s specifications. Doing so may cause the LCD display’s liquid to congeal, which can damage the LCD.

Also, if the storage area’s temperature becomes higher than the specified level, the LCD’s liquid may

become isotropic, causing irreversible damage to the LCD. Therefore, only store the PS-A unit in areas

where temperatures are within the PS-A unit’s specifications.

After turning OFF the PS-A unit, be sure to wait at least 5 seconds before turning it ON again. The PS-A

unit may not operate correctly if it is restarted too quickly.

Due to the possibility of unexpected accidents, be sure to back up the PS-A unit’s data regularly.

Information Symbols

This manual uses the following icons:

About the Manuals

For the detailed information on PS-A series, refer to the following manuals.

• PS-3650A/PS-3651A Series Hardware Manual

• PS-3650A/PS-3651A Series Reference Manual

• PS-3650A/PS-3651A Series API Reference Manual

• Installation Guides for various optional items

The manuals can be downloaded from Pro-face Home Page, “Otasuke Pro!”.

“Otasuke Pro!” URL

http://www.pro-face.com/otasuke/

Indicates a warning or a product limitation. Be sure to follow the instructions

given with this icon to ensure the safe operation of the PS-A unit.

Contains additional or useful information.

(1) (2) Indicates steps used to accomplish a given task.

Be sure to follow these steps in the order they are written.

* Indicates useful or important supplemental information.

Indicates pages containing related information.

• PS-A specifications may change when optional items are used. Check the

optional item installation guides’ specifications for variances, if any.

SEE

PS-3650A/PS-3651A Series Model Names

The term “PS-3650A/PS-3651A” Series refers to the following model numbers:

PS-3650A/PS-3651A Series Model Name Indication

Model name

PS365

∗A-T42

∗

Series Models Type

PS-3650A

Series

PS3650A-T42 PS-3650A Series AC Power Supply Type

PS3650A-T42S

PS3650A-T42-24V PS-3650A Series DC Power Supply Type

PS3650A-T42S-24V

PS-3651A

Series

PS3651A-T42 PS-3651A Series AC Power Supply Type

PS3651A-T42S

PS3651A-T42-24V PS-3651A Series DC Power Supply Type

PS3651A-T42S-24V

• For the models other than the above listed PS-3650A/PS-3651A Series, please refer to the

following PDF manual:

"PS-3650A/PS-3651A Series User Manual"

The manuals can be downloaded from the Pro-face home page.

http://www.pro-face.com/otasuke/

a0 PCI expansion slot type

1 Fan less type

bnone RAS port type

S Serial 2 port type

cnone AC Power Supply Type

24V DC Power Supply Type

abc

Package Contents

The following items are included in the PS-A unit’s package. Before using the PS-A unit, please check that all items listed

here are present.

This unit has been carefully packed, with special attention to quality. However, should you find anything damaged or

missing, please contact your local PS-A distributor immediately.

PS-A Unit (1) English and Japanese

Installation Guides (one of each) Installation Fasteners (4/set)

Installation Gasket (1)

(Attached to the PS-A unit) USB Holder (2) sets

(USB Holder (1) + USB Cover (2)) x 2

Power Plug (1)

(Attached to the PS-A unit)

• If your PS-A unit contains a built-in accessory, that accessory’s Installation Guide will also be

included in the PS-A unit’s packing box. Please check that all items normally included with that

accessory are also included in this box.

Installation

Guide

ACPowerSupply

Type 5.08mm

[0.2 in.] pitch

DCPowerSupply

Type 7.62mm

[0.3 in.] pitch

Installation prerequisites for standards

• UL listed products

• c-UL listed products

• Product List

UL/c-UL File No.: E220851

For the detailed certification's information, refer to the Pro-face Home page.

Be aware of the following items when building the PS-A into an end-use product:

• The PS-A unit’s rear face is not approved as an enclosure. When building the PS-A unit into an end-use product, be

sure to use an enclosure that satisfies standards as the end-use product’s overall enclosure.

• The PS-A unit must be used indoors only.

• Install and operate the PS-A with its front panel facing outwards.

• If the PS-A is mounted so as to cool itself naturally, be sure to install it in a vertical panel. Also, it’s recommended that

the PS-A should be mounted at least 50 mm [1.97 in.] away from any other adjacent structures or machine parts. The

temperature must be checked on the final product in which the PS-A is installed.

• For use on a flat surface of a Type 4X (Indoor Use Only) and/or Type 12 Enclosure.

• Type 4X (Indoor Use Only) and/or 12 Enclosure, when the hatch for Front USB Port is secured by screw.

Type 1 Enclosure, when the hatch for Front USB Port is open.

• The temperature rating of field installed conductors: 75 oC only.

The safety certificate can be downloaded from Pro-face Home Page.

Home Page URL

http://www.pro-face.com/

Industrial Control Equipment refer to UL508 see [a] in the

“Product List“

Process Control Equipment refer to CSA-C22.2

No.142 see [b] in the

“Product List“

Product Model No. Registration Model

No. UL c-UL

[a] [b]

PS3650A-T42 3480801-02 99

PS3650A-T42S 99

PS3651A-T42 3480801-01 99

PS3651A-T42S 99

PS3650A-T42-24V 3480801-12 99

PS3650A-T42S-24V 99

PS3651A-T42-24V 3480801-11 99

PS3651A-T42S-24V 99

Andere Handbücher für PS-3650A Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Pro-face Touchscreen Handbücher

Pro-face

Pro-face GP-3310T Stücklistenhandbuch

Pro-face

Pro-face GP3000 Series Betriebsanleitung

Pro-face

Pro-face PS-3600G Series Bedienungsanleitung

Pro-face

Pro-face GP577R-SC11 Stücklistenhandbuch

Pro-face

Pro-face PL-6920 Series Bedienungsanleitung

Pro-face

Pro-face GP3000 Series Bedienungsanleitung

Pro-face

Pro-face SP5000 Series Bedienungsanleitung

Pro-face

Pro-face LogiTouch GLC150-BG41-RSFL-24V Bedienungsanleitung

Pro-face

Pro-face GP-4400 Series Bedienungsanleitung

Pro-face

Pro-face FP-3710K Series Bedienungsanleitung

Pro-face

Pro-face GP3000 Series Bedienungsanleitung

Pro-face

Pro-face PS-3710A Series Bedienungsanleitung

Pro-face

Pro-face PS-4700 Series Bedienungsanleitung

Pro-face

Pro-face PL-7900 Series Bedienungsanleitung

Pro-face

Pro-face PS-3700A Bedienungsanleitung

Pro-face

Pro-face PL-6700 Series Bedienungsanleitung

Pro-face

Pro-face PS-3600G Series Bedienungsanleitung

Pro-face

Pro-face PFXGP4502WADW Bedienungsanleitung

Pro-face

Pro-face GP37W2-BG41-24V Bedienungsanleitung

Pro-face

Pro-face PS-3710A Series Bedienungsanleitung

Pro-face

Pro-face GP4104G1D Bedienungsanleitung

Pro-face

Pro-face PFXGP4401TADR Bedienungsanleitung

Pro-face

Pro-face GP-2500 Series Bedienungsanleitung

Pro-face

Pro-face GP-2400 Series Bedienungsanleitung

Beliebte Touchscreen Handbücher anderer Marken

FlowLine

FlowLine Data loop Bedienungsanleitung

ALPEX

ALPEX AEx-8 P Series Bedienungsanleitung

Ltech

Ltech E5S Bedienungsanleitung

Harman

Harman AMX MODERO S MSD-701-L2 Bedienungsanleitung

Acnodes

Acnodes PC 1150 Bedienungsanleitung

AIS

AIS IP10IA99 series Bedienungsanleitung

IBASE Technology

IBASE Technology ASTUT-152-RE1S Bedienungsanleitung

YASKAWA

YASKAWA TP 610C Bedienungsanleitung

B&R

B&R Power Panel C Series Bedienungsanleitung

Beijer Electronics

Beijer Electronics X2 control Bedienungsanleitung

AXIOMTEK

AXIOMTEK GOT321W-521 Bedienungsanleitung

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Bedienungsanleitung

Qomo

Qomo QIT1386 Bedienungsanleitung

DFI

DFI KS104-CD Bedienungsanleitung

AMX

AMX AXP-PPC Leitfaden

Sartorius

Sartorius X3 PR 5410 Bedienungsanleitung

AMX

AMX Modero X Series Bedienungsanleitung

Advantech

Advantech TPC-30 Series Bedienungsanleitung