Pro-face PS-3710A Series Bedienungsanleitung

+DUGZDUH0DQXDO

36$36$6HULHV

Industrial automation

Elincom Group

EuropeanUnion:www.elinco.eu

Russia: www.elinc.ru

Preface

Thank you for purchasing Pro-face’s PS-3710A/PS-3711A Series (Hereafter referred to as the “PS-A unit”).

Before operating your PS-A unit, be sure to read this manual to familiarize yourself with the PS-A unit’s operation

procedures and features.

Product names used in this manual are the trademarks / registered trademarks of their respective owners.

NOTICE

1. Copying this manual’s contents, either in whole or in part, is prohibited without the express permission of Digital

Electronics Corporation, Japan.

2. The information contained in this manual is subject to change without notice.

3. If you should you find any errors or omissions in this document, please contact Digital Electronics Corporation to

report your findings.

4. Regardless of Clause 3 above, Digital Electronics Corporation shall not be held responsible for any damages,

losses or third-party damages resulting from the use of this product.

Essential Safety Precautions

All safety-related procedures stated in this document must be followed to operate the PS-A correctly and safely. Be sure to

read this and any related documents thoroughly to understand the correct operation and functions of the PS-A unit.

Safety Icons

Throughout this manual, these icons provide essential safety information for PS-A operation procedures requiring special

attention. These icons indicate the following levels of danger:

System Design

Indicates situations where severe bodily injury, death or major equipment damage

can occur.

Indicates situations where slight bodily injury or minor equipment damage can

occur.

Indicates actions or procedures that should NOT be performed.

Indicates actions or procedures that MUST be performed to ensure correct unit

operation.

Do not create PS-A touch panel switches that could possibly endanger the safety of personnel or

equipment.

A malfunction of the PS-A unit, its I/O unit(s), cable(s), or other related equipment can cause unexpected

output signals, leading to a serious accident. Be sure to design all important machine operation switches

so they are operated via a separate control system, and not via the PS-A.

Do not create PS-A touch panel switches to control machine safety operations, such as an emergency

stop switch. Install these switches as separate hardware switches, otherwise severe bodily injury or

equipment damage can occur.

Be sure to design your system so that a communication fault between the PS-A and its host controller will

not cause equipment to malfunction. This is to prevent any possibility of bodily injury or equipment

damage.

Do not use the PS-A as a warning device for critical alarms that can cause serious operator injury,

machine damage or can halt system operation. Critical alarm indicators and their control/activator units

must be designed using stand-alone hardware and/or mechanical interlocks.

Handling

Wiring

Maintenance

Do not use the PS-A with aircraft control devices, aerospace equipment, central trunk data transmission

(communication) devices, nuclear power control devices, or medical life support equipment, due to these

devices’ inherent requirements of extremely high levels of safety and reliability.

When using the PS-A with transportation vehicles (trains, cars, and ships), disaster and crime prevention

devices, various types of safety equipment, and medical devices that are not life-support related, use

redundant and/or failsafe system designs to ensure proper reliability and safety.

After the PS-A unit’s backlight burns out the touch panel is still active, unlike the PS-A unit’s “Standby

Mode”. If the operator fails to notice that the backlight is burned out and touches the panel, a potentially

dangerous machine operation error can occur. Therefore, do not create PS-A unit touch panel switches

that may cause injury and/or equipment damage. If your PS-A unit’s backlight suddenly turns OFF, use the

following steps to determine if the backlight is actually burned out.

1) If the PS-A unit’s “Backlight Control” is not set and the screen has gone blank, your backlight is burned

out.

2) If the PS-A unit’s “Backlight Control” is set to Standby Mode and the screen has gone blank, and

touching the screen or performing another input operation does not cause the display to reappear,

your backlight is burned out.

Do not disassemble or modify the PS-A unit. Doing so may cause a fire or an electric shock.

Do not operate the PS-A in an environment where flammable gases are present, since it may cause an

explosion.

To prevent electrical shock or equipment damage, unplug the PS-A unit’s power cord from the power

supply prior to installing or wiring the PS-A.

Do not use the voltage not specified in the manual. Doing so may cause a fire or an electric shock.

Do not connect or disconnect Host and PS-A unit communication cables while the PS-A is turned ON.

The PS-A uses a lithium battery for backing up its internal clock data and the battery may explode if it is

replaced incorrectly. When replacement is required, use a Pro-face-designated replacement product.

SEE “4.6 Replacing the Internal Battery” (page 4-13)

Installation

Wiring

Maintenance

Unit Disposal

General Safety Precautions

Be sure all cable connectors are securely attached to the PS-A unit. A loose connection may cause

incorrect input or output signals.

Be sure to ground the PS-A unit’s FG wire separately from other equipment FG lines. Also, be sure to use

a grounding resistance of 100Ωor less and a 2mm2or thicker wire, or your country’s applicable standard.

Otherwise, electric shock or malfunctions may result.

Be sure to use only the designated torque to tighten the PS-A unit’s terminal block screws. If these screws

are not tightened firmly, it may cause a short-circuit, fire or incorrect unit operation.

Be sure that metal particles and wiring debris do not fall inside the PS-A unit. They can cause a fire,

malfunction or incorrect unit operation.

Do not reset or turn the PS-A OFF, or insert or remove the CF Card while the PS-A unit’s CF Card or hard

disk is being accessed. Otherwise, CF Card and the hard disk internal data may be damaged or lost.

When the product is disposed of, it should be done so according to your country’s regulations for similar

types of industrial waste.

Do not press on the PS-A unit’s display with excessive force or with a hard object, since it can damage the

display. Also, do not press on the touch panel with a pointed object, such as the tip of a mechanical pencil

or a screwdriver, since doing so can damage the touch panel.

Do not install the PS-A where the ambient temperature exceeds the specified range. Doing so may cause

a unit malfunction.

To prevent abnormally high temperatures from occurring inside the PS-A, do not restrict or block the PS-A

unit’s rear-face ventilation slots.

Do not operate the PS-A in areas where large, sudden temperature changes can occur. These changes

can cause condensation to form inside the PS-A, possibly causing it to malfunction.

Do not allow water, liquids or metal fragments to enter inside the PS-A unit’s case, since they can cause

either a malfunction or an electric shock. The allowable pollution degree is 2.

LCD Panel Usage Precautions

• The LCD panel’s liquid contains an irritant. If the panel is damaged and any of this liquid contacts your skin,

immediately rinse the area with running water for at least 15 minutes. If the liquid gets in your eyes, immediately rinse

your eyes with running water for at least 15 minutes and consult a doctor.

• The PS-A unit’s LCD screen may flicker or show unevenness in the brightness of certain images or at some contrast

settings. This is an LCD characteristics and not a product defect.

• Some LCD screens may have differences in brightness and tone. Please be aware of this difference when using

multiple units side by side.

• Depending on the ambient temperature, LCD screens may sometimes look whitish (at high temperatures) or blackish

(at low temperatures). This is an LCD characteristic and not a product defect.

• Some of PS-A unit's LCD screens may contain black and white colored pixels. This is an LCD characteristic and not a

product defect.

• Extended shadows, or "Crosstalk" may appear on the LCD screen. This is an LCD characteristic and not a product

defect.

• The color displayed on the PS-A unit’s LCD screen may appear different when seen from outside the specified viewing

angle. This is an LCD characteristic and not a product defect.

Do not operate or store the PS-A in locations where it can be exposed to direct sunlight, high

temperatures, excessive dust, moisture or vibration.

Do not operate or store the PS-A where chemicals evaporate, or where chemicals are present in the air.

Corrosive chemicals: Acids, alkalines, liquids containing salt

Flammable chemicals: Organic Solvents

Do not use paint thinner or organic solvents to remove dirt or oil from the PS-A unit’s surface. Instead, use

a soft cloth moistened with a diluted neutral detergent.

Do not use or store the PS-A in areas with direct sunlight, since the sun’s ultraviolet rays may cause the

LCD’s quality to deteriorate.

Do not store the PS-A in an area where the temperature is lower than that recommended in the PS-A

unit’s specifications. Doing so may cause the LCD display’s liquid to congeal, which can damage the LCD.

Also, if the storage area’s temperature becomes higher than the specified level, the LCD’s liquid may

become isotropic, causing irreversible damage to the LCD. Therefore, only store the PS-A in areas where

temperatures are within the PS-A unit’s specifications.

After turning OFF the PS-A unit, be sure to wait at least 5 seconds before turning it ON again. The PS-A

unit may not operate correctly if it is restarted too quickly.

Due to the possibility of unexpected accidents, be sure to back up the PS-A unit's data regularly.

• When the same image is displayed on the PS-A unit’s screen for a long period, an afterimage may appear when the

image is changed. If this happens, turn off the PS-A, wait 10 seconds and then restart the unit. This is an LCD

characteristic and not a product defect.

• To prevent an afterimage:

* Set the PS-A unit’s display OFF feature when you plan to display the same screen image for a long period of time.

* Change the screen image periodically and try to not display the same image for a long period of time.

Information Symbols

This manual uses the following icons:

About the Manuals

For the detailed information on PS-A series, refer to the following manuals.

• PS-3710A/PS-3711A Series Hardware Manual

• PS-3710A/PS-3711A Series Reference Manual

• PS-3710A/PS-3711A Series API Reference Manual

• Installation Guides for various optional items

The manuals can be downloaded from Pro-face Home Page, “Otasuke Pro!”.

“Otasuke Pro!” URL

http://www.pro-face.com/otasuke/

Indicates a warning or a product limitation. Be sure to follow the instructions given with

this icon to ensure the safe operation of the PS-A.

* Indicates useful or important supplemental information.

Contains additional or useful information.

Indicates pages containing related information.

• PS-3710A/PS-3711A specifications may change when optional items are used.

Check the optional item installation guides’ specifications for variances, if any.

SEE

PS-3710A/PS-3711A Series Model Names

The term “PS-3710A/PS-3711A” Series refers to the following numbers:

Series Models Type

PS-3710A Series

PS3710A-T41 PS-3710A Series AC Power Supply Type

PS3710A-T42

PS3710A-T41-24V PS-3710A Series DC Power Supply Type

PS3710A-T42-24V

PS-3711A Series

PS3711A-T41 PS-3711A Series AC Power Supply Type

PS3711A-T42

PS3711A-T41-24V PS-3711A Series DC Power Supply Type

PS3711A-T42-24V

Package Contents

The following items are included in the PS-A unit’s package. Before using the PS-A, please check that all items listed

here are present.

This unit has been carefully packed, with special attention to quality. However, should you find anything damaged or

missing, please contact your local PS-A distributor immediately.

PS-A Unit: 1 • Installation Guides

(Set of Japanese/Set

of English)

• Warning/Caution

Information (1)

Installation Gasket: 1

(Attached to the PS-A

unit)

Installation Fasteners: 4

per set x2

USB Cable Clamp: (2 ports) 2

Power Connector: 1

Power Switch cover (1 set) (cover:1, secrew:1)

(AC Power Supply type Only)

• Be careful when installing the PS-A not to damage the built-in HDD.

(for AC Power Supply type)

(5.08mm [0.2in.] pitch)

AC Power Supply type

(only for PS-3711A Series

DC Power Supply type)

(only for PS-3710A Series

DC Power Supply type)

(7.62mm [0.3in.] pitch)

DC Power Supply type

PS-3710A Series PS-3711A Series

UL/c-UL/CSA Approval

• UL listed products

• c-UL listed products

• CSA listed products

• Product List

UL/c-UL File No.: E220851, E210412

CSA File No.219866

Industrial Control Equipment refer to UL508 see [a] in the

“Product List“

Suitable for use in Class I, Division 2,

Groups A, B, C, and D Hazardous (clas-

sified) locations, or Non-Hazardous

Locations.

refer to

ANSI/ISA 12.12.01 see [b] in the

“Product List“

Process Control Equipment refer to CSA-C22.2

No.142 see [c] in the

“Product List“

Suitable for use in Class I, Division 2,

Groups A, B, C, and D Hazardous (clas-

sified) locations, or Non-Hazardous

Locations.

refer to

CSA-C22.2 No. 213 see [d] in the

“Product List“

Process Control Equipment refer to CSA-C22.2

No.142 see [e] in the

“Product List“

Product Model No. Registration Model No. UL c-UL CSA

[a] [b] [c] [d] [e]

PS3710A-T41 3580301-01 --

PS3710A-T41-24V 3580301-12 --

PS3711A-T41 3580301-03 --

PS3711A-T41-24V 3580301-11 --

PS3710A-T42 3580301-01  -

PS3710A-T42-24V 3580301-12  -

PS3711A-T42 3580301-03  -

PS3711A-T42-24V 3580301-11  -

Andere Handbücher für PS-3710A Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Pro-face Touchscreen Handbücher

Pro-face

Pro-face GP-4400 Series Bedienungsanleitung

Pro-face

Pro-face GP4104G1D Bedienungsanleitung

Pro-face

Pro-face PS-3600G Series Bedienungsanleitung

Pro-face

Pro-face PS-4700 Series Bedienungsanleitung

Pro-face

Pro-face GP3000 Series Bedienungsanleitung

Pro-face

Pro-face GP-3400 Series Bedienungsanleitung

Pro-face

Pro-face GP-3310T Stücklistenhandbuch

Pro-face

Pro-face PS-3700A Bedienungsanleitung

Pro-face

Pro-face GP-577R Series Bedienungsanleitung

Pro-face

Pro-face FP2600-T11 Bedienungsanleitung

Pro-face

Pro-face GP377-LG Series Stücklistenhandbuch

Pro-face

Pro-face AGP3200-A1-D24 Bedienungsanleitung

Pro-face

Pro-face FP-3710K Series Bedienungsanleitung

Pro-face

Pro-face PL-6700 Series Bedienungsanleitung

Pro-face

Pro-face PL-7900 Series Bedienungsanleitung

Pro-face

Pro-face PS-4700 Series Bedienungsanleitung

Pro-face

Pro-face PL-5900 Series Bedienungsanleitung

Pro-face

Pro-face PFXGP4502WADW Bedienungsanleitung

Pro-face

Pro-face LogiTouch GLC150-BG41-RSFL-24V Bedienungsanleitung

Pro-face

Pro-face GP4000 SERIES Bedienungsanleitung

Pro-face

Pro-face GP77R Series Gebrauchsanweisung

Pro-face

Pro-face GP-377RT Bedienungsanleitung

Pro-face

Pro-face GP3000 Series Betriebsanleitung

Pro-face

Pro-face GP-2500 Series Bedienungsanleitung

Beliebte Touchscreen Handbücher anderer Marken

FlowLine

FlowLine Data loop Bedienungsanleitung

ALPEX

ALPEX AEx-8 P Series Bedienungsanleitung

Ltech

Ltech E5S Bedienungsanleitung

Harman

Harman AMX MODERO S MSD-701-L2 Bedienungsanleitung

Acnodes

Acnodes PC 1150 Bedienungsanleitung

AIS

AIS IP10IA99 series Bedienungsanleitung

IBASE Technology

IBASE Technology ASTUT-152-RE1S Bedienungsanleitung

YASKAWA

YASKAWA TP 610C Bedienungsanleitung

B&R

B&R Power Panel C Series Bedienungsanleitung

Beijer Electronics

Beijer Electronics X2 control Bedienungsanleitung

AXIOMTEK

AXIOMTEK GOT321W-521 Bedienungsanleitung

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Bedienungsanleitung

Qomo

Qomo QIT1386 Bedienungsanleitung

DFI

DFI KS104-CD Bedienungsanleitung

AMX

AMX AXP-PPC Leitfaden

Sartorius

Sartorius X3 PR 5410 Bedienungsanleitung

AMX

AMX Modero X Series Bedienungsanleitung

Advantech

Advantech TPC-30 Series Bedienungsanleitung