Radio Shack Sprint SP-514 Bedienungsanleitung

OWNER’S MANUAL

25-Channel Lighted

Big Button Cordless Phone

Cat. No. 43-5514

SP-514

43-5514.fm Page 1 Wednesday, August 18, 1999 12:47 PM

This symbol is intended to alert you to the presence of uninsulated

dangerous voltage within the product’s enclosure that might be of

sufficientmagnitude to constitutea risk ofelectric shock. Do notopen

the product’s case.

This symbol is intended to inform you that important operating and

maintenance instructions are included in the literature accompanying

this product.

Important: Cordless phones such as this one require AC power to

operate. When the AC power is off, you cannot dial out or receive

incoming calls using your SP-514. For this reason, the SP-514

cordless phone should not be your only telephone. To be safe, you

should also have a phone that does not require AC power to oper-

ate (not a cordless phone) so you can still make and receive calls if

there is an AC power failure.

Your SP-514 operates on standard radio frequencies, as allocated

by the FCC. Therefore, it is possible for other radio units operating

on similar frequencies, within a certain area, to inadvertently inter-

cept your conversations and/or cause interference on your cord-

less telephone. This lack of privacy can occur with any cordless

telephone.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE COVER OR BACK. NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED PERSONNEL.

WARNING: To reduce the risk of fire or shock hazard, do not

expose this product to rain or moisture.

RadioShack is a registered trademark used by Tandy Corporation.

The Sprint Logo is a registered trademark of Sprint Communications Company L.P. Used under license.

43-5514.fm Page 2 Wednesday, August 18, 1999 12:47 PM

nFeatures

Your RadioShack SP-514 25-Channel Lighted Big Button Cordless

Phone offers the latest advances in cordless phone technology

with large lighted keys for easy-to-see dialing. Its cordless opera-

tion lets you handle calls just about anywhere in your home or of-

fice.

The SP-514 has these features:

25 Channels — automatically selects a clear channel when you

make or answer a call. You can also manually change channels

during a call.

Volume Control — lets you adjust the volume you hear through

the handset.

Handset Locator/Paging System — lets you send a signal from

the base to the handset to page someone or locate the handset

when it is away from the base.

10-Number Memory Dialing — lets you store 10 numbers in

memory for easy dialing.

21-Day Battery — the supplied battery (when fully charged) pro-

vides about 21 days of standby time.

Redial — lets you quickly redial the last number dialed.

Flash — sends an electronic switchhook signal for use with spe-

cial phone services such as Call Waiting.

Security Access-Protection Code — changes each time you un-

plug the phone from AC power, to help prevent other cordless

phone users from using your phone linewhile the handset is off the

base.

43-5514.fm Page 3 Wednesday, August 18, 1999 12:47 PM

This telephone has been tested and found to comply with all appli-

cable UL and FCC standards.

We recommend you record your phone’s serial number here. The

number is on the bottom of the base.

Serial Number: __________________

READ THIS BEFORE INSTALLATION

Each device that you connect to the phone line draws power from

the phone line. We refer to this power draw as the device’s

ringer

equivalence number

, or REN. The REN is on the bottom of the

base.

If you are using more than one phone or other device on the line,

add up all the RENs. If the total is more than five, your phone might

not ring. In rural areas, a total REN of three might impair ringer op-

eration. If ringer operation is impaired, remove a device from the

line.

FCC STATEMENT

This telephone complies with Part 68 of

FCC Rules

. You must,

upon request, provide the FCC registration number and the REN

to your phone company. These numbers are on the bottom of the

base.

Note: You must not connect your SP-514 to any of the following:

²coin-operated systems

²party-line systems

²most electronic key phone systems

43-5514.fm Page 4 Wednesday, August 18, 1999 12:47 PM

nCONTENTS

Installation ................................................................................. 6

Selecting a Location ............................................................. 6

Placing the Base on a Desk Top ........................................... 7

Mounting the Base on a Wall ................................................ 8

Installing and Charging the Battery Pack .............................. 9

Preparation ............................................................................... 11

Setting the Dialing Mode ...................................................... 11

Setting the Handset’s Ringer .............................................. 12

Telephone Operation ............................................................... 12

Making and Receiving a Call .............................................. 12

Setting the Handset’s Volume ............................................. 13

Changing the Channel ........................................................ 14

Using Redial ....................................................................... 14

Using Flash ......................................................................... 15

Using Mute .......................................................................... 15

Using Tone Services on a Pulse Line ................................. 16

Using Page/Handset Locator .............................................. 16

Memory Dialing ................................................................... 17

Storing a Number in Memory ....................................... 17

Entering a Pause .......................................................... 18

Dialing a Memory Number ............................................ 19

Chain-Dialing Service Numbers ................................... 19

Testing Stored Emergency Numbers ............................ 19

Troubleshooting ...................................................................... 20

Care and Maintenance ............................................................ 23

Replacing the Handset Battery Pack .................................. 24

The FCC Wants You to Know ............................................. 25

Lightning ............................................................................. 26

Notes ........................................................................................ 27

43-5514.fm Page 5 Wednesday, August 18, 1999 12:47 PM

Installation

n Installation

SELECTING A LOCATION

You can place the phone on a desk top or table, mount it on a stan-

dard wall plate, or mount it directly on the wall. Select a location

that is:

²near an AC outlet not controlled by a wall switch

²near a telephone line jack

²out of the way of normal activities

²away from electrical machinery, electrical appliances, metal

walls or filing cabinets, wireless intercoms, alarms, and room mon-

itors

The base’s location affects the phone’s range.If you have a choice

of several locations, try each to see which provides the best perfor-

mance.

Caution: You must use a Class 2 power source that supplies 12

volts DC and delivers at least 200 mA. Its center tip must be set to

positive and its plug must fit the SP-514's POWER jack. The sup-

plied adapter meets these specifications. Using an adapter that

does not meet these specifications could damage the SP-514 or

the adapter.

Notes:

²Your telephone connects directly to a modular telephone line

jack. If your phone line jack is not a modular jack, you can update

the wiring yourself, using jacks and adapters available at your local

RadioShack store. Or, you can let the phone company update the

wiring for you.

²The USOC number of the jack to be installed is RJ11C (RJ11W

for a wall plate).

43-5514.fm Page 6 Wednesday, August 18, 1999 12:47 PM

Installation

PLACING THE BASE ON A DESK TOP

Follow these steps when you place the base on a desk, shelf, or

table.

1Plug one end of the supplied long modular cord into the modu-

lar cord jack on the back of the base.

2Route the modular cord through the channel slot on the bottom

of the base.

3Insert the supplied AC adapter’s barrel plug into the POWER

jack on the back of the base.

4Route the adapter’s cord through the other channel slot on the

bottom of the base.

5Plug the modular cord’s other end into a modular phone line

jack.

6Plug the adapter into a standard AC outlet.

7Fully extend the base’s antenna and raise it to a vertical posi-

tion.

Modular Cord POWER Jack

Channel Slots

(bottom of base)

Antenna

Jack

43-5514.fm Page 7 Wednesday, August 18, 1999 12:47 PM

Installation

MOUNTING THE BASE ON A WALL

Note: To mount the base directly on the wall, you need two screws

(not supplied) with heads that fit into the keyhole slots on the bot-

tom of the base. Drill two holes 315/16 inches (100 mm) apart, one

above the other. Then thread a screw into each hole, letting the

heads extend about 5/16 inch (7 mm) from the wall.

1Plug one end of the sup-

plied modular cord into the

modular cord jack and the

supplied AC adapter’s barrel

plug into the POWER jack on

the back of the base.

2Route the adapter cord

and modular cord through the

channel slots on the bracket’s

narrow end. Wrap the excess

modular cord in the groove in

the bottom of the base. Route

the end of the adapter cord

through the channel slot at

the bottom of the base.

3Plug the modular cord’s

loose end into the wall plate

jack (or a modular phone line

jack), align the base’s key-

hole slots with the wall plate

studs (or the screws in the

wall), and slide the base

downward to secure it.

4Plug the adapter into a

standard AC outlet. Fully ex-

tend the base’s antenna and

raise it to a vertical position

Modular Cord Jack POWER Jack

43-5514.fm Page 8 Wednesday, August 18, 1999 12:47 PM

Installation

INSTALLING AND CHARGING THE BATTERY PACK

The SP-514 is packaged with a rechargeable nickel-cadmium bat-

tery pack. Before using your phone, you must install the battery

pack and then charge it for 10 hours.

Press down and slide off the

compartment cover. Plug the

battery connector into the

socket inside the compart-

ment. Then place the battery

pack into the compartment

and replace the cover.

Note: The connector fits only one way. Do not force it.

To charge the battery pack,

simply place the handset

facedown on the base. The

CHARGING indicator on the

base lights.

Recharge the battery pack

when the LOW BATT indica-

tor on the handset flashes.

LOW BATT

Indicator

43-5514.fm Page 9 Wednesday, August 18, 1999 12:47 PM

Installation

Notes:

²When you first use the phone after charging or recharging the

battery pack, the phone might not work and you might hear a two-

beep signal when you press PHONE. If this happens, return the

handset to the base for about 30 seconds. This resets the security

access protection code.

²If the CHARGING indicator does not light when you place the

handset on the base, be sure the battery pack and AC adapter are

correctly and securely connected.

Also, check the charging

contacts on the handset and

the base. If the contacts are

dirty or tarnished, clean them

with a pencil eraser.

²If the battery pack gets completely discharged or the base loses

power while the handset is away from it, the security access-

protection code needs to be reset. To reset the code, place the

handset on the base for about 30 seconds. If it was the handset

that lost power, leave the handset on the base to charge the bat-

tery pack.

²If the battery pack gets weak during a call, the handset sounds

4 beeps every 30 seconds. If this happens, you cannot make

another call on the phone until you recharge the battery pack.

²About once a month, fully discharge the battery pack by keep-

ing the handset off the base until the LOW BATT indicator lights.

Otherwise, the battery pack loses its ability to fully recharge.

²If you are not going to use your phone for an extended period of

time, disconnect the battery pack. This increases the battery

pack’s usable life.

Charging

Contacts

43-5514.fm Page 10 Wednesday, August 18, 1999 12:47 PM

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Radio Shack Schnurloses Telefon Handbücher

Radio Shack

Radio Shack 43-3856 Bedienungsanleitung

Radio Shack

Radio Shack TAD-268 Bedienungsanleitung

Radio Shack

Radio Shack 43-5829 Bedienungsanleitung

Radio Shack

Radio Shack 43-3575 Bedienungsanleitung

Radio Shack

Radio Shack 900 MHz Digital Spread Spectrum Cordless Phone with Digital Answerer and Caller ID/Call Waiting... Bedienungsanleitung

Radio Shack

Radio Shack 43-5560 Bedienungsanleitung

Radio Shack

Radio Shack RT-551 Bedienungsanleitung

Radio Shack

Radio Shack ET-908 Bedienungsanleitung

Radio Shack

Radio Shack ET-1123 Bedienungsanleitung

Radio Shack

Radio Shack 43-3814 Bedienungsanleitung

Radio Shack

Radio Shack TAD-1016 Bedienungsanleitung

Radio Shack

Radio Shack 43-141 Bedienungsanleitung

Radio Shack

Radio Shack 43-3704 Bedienungsanleitung

Radio Shack

Radio Shack ET-3504 Bedienungsanleitung

Radio Shack

Radio Shack 43-3821 Bedienungsanleitung

Radio Shack

Radio Shack ET-557 Bedienungsanleitung

Radio Shack

Radio Shack ET-1106 Bedienungsanleitung

Radio Shack

Radio Shack 43-683 Bedienungsanleitung

Radio Shack

Radio Shack 43-3856 Bedienungsanleitung

Radio Shack

Radio Shack 2.4 GHz 2-Line Digital Spread Spectrum Cordless Phone with Call Waiting/Caller... Bedienungsanleitung

Radio Shack

Radio Shack 43-3585 Bedienungsanleitung

Radio Shack

Radio Shack ET-153 Bedienungsanleitung

Radio Shack

Radio Shack ET-596 Bedienungsanleitung

Radio Shack

Radio Shack ET-910 Bedienungsanleitung

Beliebte Schnurloses Telefon Handbücher anderer Marken

3Com

3Com NBX Bedienungsanleitung

Panasonic

Panasonic KX-TGK210HK Bedienungsanleitung

Panasonic

Panasonic KX-TCA181EX Bedienungsanleitung

BT FREESTYLE 3200 Bedienungsanleitung

AT&T

AT&T CL84102 Bedienungsanleitung

BREZZICNI

BREZZICNI CL-3622 Bedienungsanleitung

Panasonic

Panasonic KX-TG1831NZ Bedienungsanleitung

Panasonic

Panasonic KX-TG7301E Bedienungsanleitung

Sanyo

Sanyo CLT-J70 Bedienungsanleitung

Amplicomms

Amplicomms BigTel 201 Bedienungsanleitung

GE 26992 Bedienungsanleitung

AT&T

AT&T E1812B Bedienungsanleitung

Sanyo

Sanyo CLT-670 Bedienungsanleitung

GE 15432970 Bedienungsanleitung

Curtis

Curtis TC595 Bedienungsanleitung

Gigaset

Gigaset Gigaset 3000 Micro Bedienungsanleitung

Poly

Poly VVX D230 Einrichtungshandbuch

AT&T

AT&T 7625 Bedienungsanleitung