Radio Shack ET-543 Bedienungsanleitung

Cat. No. 43-1043

OWNER’S MANUAL

LCD Display 25-Channel

Please read before using this equipment.

ET-543

Cordless Telephone

43-1043.fm Page 1 Tuesday, August 17, 1999 10:36 AM

FEATURES

COM-LOK is a registered trademark used by Tandy Corporation.

RadioShack is a trademark used by Tandy Corporation.

Your RadioShack ET-543 LCD Display

25-Channel Cordless Telephone of-

fers the latest advances in cordless

phone technology, and includes these

features:

LCD Displa

— lets you see phone

numbers as you dial them or recall

them from the ET-543’s memory.

Auto Scan — automatically selects

the clearest channel when you pick up

the phone.

25-Channel Selector — lets you man-

ually change channels to find one with

the least interference.

Advanced Super CCT Circuitr

—

provides clarity comparable to a cord-

ed phone, reduces background noise,

and increases effective operating dis-

tance.

COM-LOK®— ensures that other

cordless phone users cannot use your

phone line while the handset is on the

base.

Automatic Securit

Access Code —

changes each time you disconnect and

restore power to the base to help pre-

vent other cordless phone users from

using your phone line while the hand-

set is off the base.

Flash — sends an electronic switch-

hook signal for use with special phone

services such as call waiting.

Handset Volume Control — lets you

control the volume of the sound you

hear through the handset.

hted Ke

pad — lights to make the

phone easy to use when you are mak-

ing or answering a call in a dark room.

Redial — quickly redials the last num-

ber dialed with the touch of a button.

Touch Tone or Pulse (Rotar

) Dial-

— lets you connect your phone to

either type of service.

30-Number Memor

Dialin

— lets

you store 30 phone numbers in memo-

ry for easy dialing.

Please read this Owner’s Manual care-

fully so you can enjoy all of your tele-

phone’s features.

43-1043.fm Page 2 Tuesday, August 17, 1999 10:36 AM

Important: Cordless phones such as

this one require AC power to operate.

When the AC power is off, you cannot

dial out or receive incoming calls using

your ET-543. For this reason, the ET-

543 cordless phone should not be your

only telephone. To be safe, you should

alsohave aphonethatdoesnotrequire

AC power to operate (not a cordless

phone)soyoucanstillmakeandreceive

calls if there is an AC power failure.

This telephone has been tested and

found to comply with all applicable UL

and FCC standards.

Your ET-543 operates on standard ra-

dio frequencies, as allocated by the

FCC. Therefore, it is possible for other

radio units operating on similar fre-

quencies, within a certain area, to in-

advertently intercept your conversa-

tions and/or cause interference on

your cordless telephone. This lack of

privacy can occur with any cordless

telephone.

For your records, we urge you to

record the serial number of your phone

in the space below. The serial number

is located on the bottom panel of the

base.

Serial Number ______________

This symbol is intended to alert you

to the presence of uninsulated dan-

gerous voltage within the product’s

enclosure that might be of sufficient

magnitude to constitute a risk of

electric shock. Do not open the

product’s case.

This symbol is intended to inform

you that important operating and

maintenance instructions are in-

cluded in the literature accompany-

ing this product.

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER OR BACK. NO USER-SERVICE-

ABLE PARTS INSIDE. REFER SERVIC-

ING TO QUALIFIED PERSONNEL.

Warning: To prevent fire or shock

hazard, do not expose this product

to rain or moisture.

CAUTION

43-1043.fm Page 3 Tuesday, August 17, 1999 10:36 AM

READ THIS BEFORE

INSTALLATION

We have designed your telephone to

conform to federal regulations, and

you can connect it to most telephone

lines. However, each device that you

connect to the phone line draws power

from the phone line. We refer to this

power draw as the device’s ringer

equivalence number, or REN. The

REN is shown on the bottom of your

phone’s base.

If you are using more than one phone

or other device on the line, add up all

the RENs. If the total is more than five,

your phone might not ring. In rural ar-

eas, a total REN of three might impair

ringer operation. If ringer operation is

impaired, remove a device from the

line.

FCC STATEMENT

This telephone complies with Part 68

FCC Rules

. You must, upon re-

quest, provide the FCC registration

number and the REN to your phone

company. These numbers are located

on the bottom of your phone’s base.

Note: You must not connect your

phone to any of the following:

• Coin-operated systems

• Party-line systems

• Most electronic key phone sys-

tems

43-1043.fm Page 4 Tuesday, August 17, 1999 10:36 AM

CONTENTS

Installation ............................................................................................................ 6

Selecting a Location ........................................................................................ 6

Installing the Phone ........................................................................................ 6

Preparation ........................................................................................................... 7

Connecting the Battery ................................................................................... 7

Charging the Battery ....................................................................................... 7

Setting the Dialing Mode ................................................................................. 8

Operation .............................................................................................................. 9

Making/Answering a Call ................................................................................ 9

Using the Handset at the Base ................................................................. 9

Using the Handset Away from the Base ................................................... 9

Reducing Interference ................................................................................... 10

Using Redial .................................................................................................. 10

Using FLASH/DEL ........................................................................................ 10

Using Tone Services on a Pulse Line ........................................................... 11

Using Page ................................................................................................... 11

Memory Dialing ............................................................................................. 11

Storing a Number in Memory .................................................................. 12

Entering a Pause in a Memory Number ................................................. 13

Dialing a Stored Number ........................................................................ 13

Chain Dialing .......................................................................................... 14

Testing Stored Emergency Numbers ...................................................... 14

Troubleshootin

................................................................................................ 15

Care and Maintenance ...................................................................................... 17

Replacing the Battery .................................................................................... 18

The FCC Wants You to Know ....................................................................... 18

Lightning ....................................................................................................... 19

43-1043.fm Page 5 Tuesday, August 17, 1999 10:36 AM

INSTALLATION

SELECTING A LOCATION

Select a location for the telephone that

meets these requirements:

• Near an AC outlet

• Near a telephone line jack

• Out of the way of normal activities

• Away from electrical machinery,

electrical appliances, and metal

walls or filing cabinets

• Away from wireless intercoms,

alarms, and room monitors

The base’s location affects the phone’s

range. If you have a choice of several

locations, try each one to see which

provides the best performance.

If the phone line jack is not a modular

jack, you must update the wiring your-

self, using jacks and adapters avail-

able at your local RadioShack store.

Or, you can let the phone company up-

date the wiring for you.

Notes:

• The phone company will charge

you for the installation of the nec-

essary jacks.

• The USOC number of the jack to

be installed is RJ11C.

INSTALLING THE PHONE

Follow these steps to install the base

on a desk, shelf, or table.

1. Plug one end of the supplied mod-

ular cord into the phone jack on

the back of the base.

2. Plug the modular cord’s other end

into a modular phone line jack.

3. Insert the supplied AC adapter’s

barrel plug into the DC 12V jack on

the back of the base.

4. Plug the adapter into a standard

AC outlet.

For the best reception, fully extend the

base’s antenna and place it in a verti-

cal position.

Caution: You must use a 120V AC/

12V DC adapter that delivers at least

200 milliamps. Its center tip must be

positive, and its plug must correctly fit

the phone’s DC 12V jack. The supplied

adapter meets these requirements.

Using an adapter that does not meet

these requirements could damage the

phone or the adapter.

43-1043.fm Page 6 Tuesday, August 17, 1999 10:36 AM

PREPARATION

CONNECTING THE

BATTERY

Before you use your phone for the first

time, you must connect and charge the

battery.

Slide off the battery compartment cov-

er on the back of the handset. Connect

the battery’s plug to the pins inside the

compartment.

Replace the cover, then follow the in-

structions under “Charging the Bat-

tery.”

CHARGING THE

BATTERY

Before you charge the battery, set

POWER to OFF. Then place the hand-

set on the cradle so the CHARGE/

TALK indicator lights and let the bat-

tery charge for about 15 hours.

When on the handset lights, re-

charge the battery. To avoid damage

to the battery, always recharge the

handset before battery power grows

too weak to light .

Notes:

• You can set POWER to ON while

the battery charges.

• If the CHARGE/TALK indicator

does not light when you place the

handset on the cradle, be sure the

battery is connected to the pins

inside the battery compartment

and the AC adapter is securely

connected to the base. Also,

check the charging contacts on

43-1043.fm Page 7 Tuesday, August 17, 1999 10:36 AM

the handset and base. If the con-

tacts are dirty or tarnished, gently

clean them with a pencil eraser.

• About once a month, fully dis-

charge the battery by keeping the

handset off the cradle until

flashes, then return the

handset to the cradle and fully

recharge the battery. If you do not

fully discharge and recharge the

battery periodically, it loses its

ability to fully recharge.

• The first time you use your phone

after charging a new battery, the

handset might not work and might

sound an error tone when you

press

TALK. This might also occur

when you recharge a battery that

has been completely discharged.

If this happens, be sure the hand-

set is turned on, then return the

handset to the cradle for 5 sec-

onds. This resets the security

access code.

SETTING THE DIALING

MODE

Set TONE/PULSE on the back of the

base for the type of service you have.

If you are not sure which type you

have, do this test.

1. Set TONE/PULSE to TONE.

2. Lift the handset and listen for a

dial tone.

3. Press any number other than 0.

If the dial tone stops, you have

touch-tone service. Leave TONE/

PULSE set to TONE.

If the dial tone continues, you

have pulse service. Set TONE/

PULSE to PULSE.

43-1043.fm Page 8 Tuesday, August 17, 1999 10:36 AM

OPERATION

Your ET-543’s LCD display shows

telephone numbers as you dial them or

when you recall them from memory. It

shows the current channel number and

lets you know when battery power is

growing weak or the phone is out of

range of the base. The display also

shows indicators when you press

FLASH/DEL or PAUSE.

MAKING/ANSWERING

A CALL

You can use your cordless telephone

in two ways: at the base or away from

the base.

Using the Handset

at the Base

You can use the handset at the base

like a regular corded telephone. Just

set POWER to ON and place the hand-

set in the cradle.

To answer a call, just lift the handset

from the base.

To make a call, lift the handset from

the base and press TALK so the key-

pad and the CHARGE/TALK indicator

on the base light.

Note: CH and the currently used

channel number appear on the display.

This number might change when you

return the handset to the base.

To disconnect a call, replace the hand-

set on the base.

Using the Handset

Away from the Base

To make or answer a call, set POWER

to ON and press TALK. The keypad

and CHARGE/TALK indicator light.

To disconnect a call, press TALK so

the keypad light and the CHARGE/

TALK indicator turn off.

Notes:

•CHand the currently used channel

number appear on the display.

• To conserve battery power, you

can turn off the handset’s power

when you are not making or

answering a call.

43-1043.fm Page 9 Tuesday, August 17, 1999 10:36 AM

• You can make or answer a call on

a phone on the same line as the

cordless phone, even if the hand-

set is away from the base.

•RANGE appears when the dis-

tance from the handset to the

base is out of the phone’s range.

• The keypad lights on the handset

turn off if no button is pressed for

more than 13 seconds.

REDUCING

INTERFERENCE

To reduce interference, press CH to

switch to the next channel (25 chan-

nels in all) until you receive the best re-

ception. CH and the channel number

appear on the display.

USING REDIAL

To quickly redial the last number you

dialed, simply lift the handset from the

base and press TALK again so the

CHARGE/TALK indicator lights, and

then press REDIAL. The redialed num-

ber appears on the display.

The redial memory holds up to 80 dig-

its in the tone or pulse mode. The redi-

al memory also holds pause entries

(see “Entering a Pause” under “Memo-

ry Dialing”).

Note: We recommend you not use RE-

DIAL to dial numbers that include a

tone (*) entry (see “Using Tone Servic-

es on a Pulse Line”).

USING FLASH/DEL

Use FLASH/DEL on the handset to per-

form the switchhook operation for spe-

cial services, such as call waiting.

For example, if you have call waiting,

press FLASH/DEL to take an incoming

call without disconnecting the current

call. FLASH appears. Press FLASH/

DEL again to return to the first call.

43-1043.fm Page 10 Tuesday, August 17, 1999 10:36 AM

Inhaltsverzeichnis

Andere Radio Shack Schnurloses Telefon Handbücher

Radio Shack

Radio Shack 2.4 GHz Digital Spread Spectrum Cordless Telephone with Caller ID/Call... Bedienungsanleitung

Radio Shack

Radio Shack ET-521 Bedienungsanleitung

Radio Shack

Radio Shack TAD-1017 Bedienungsanleitung

Radio Shack

Radio Shack Presidian Bedienungsanleitung

Radio Shack

Radio Shack ET-1101 Bedienungsanleitung

Radio Shack

Radio Shack 43-3536 Bedienungsanleitung

Radio Shack

Radio Shack ET-689 Bedienungsanleitung

Radio Shack

Radio Shack 43-3812 Bedienungsanleitung

Radio Shack

Radio Shack 43-3815/43-3898 Bedienungsanleitung

Radio Shack

Radio Shack TAD-1016 Bedienungsanleitung

Radio Shack

Radio Shack ET-916 Bedienungsanleitung

Radio Shack

Radio Shack TAD-733 Bedienungsanleitung

Radio Shack

Radio Shack 43-3827 Bedienungsanleitung

Radio Shack

Radio Shack 43-3595 Bedienungsanleitung

Radio Shack

Radio Shack 43-3817 Bedienungsanleitung

Radio Shack

Radio Shack TAD-268 Bedienungsanleitung

Radio Shack

Radio Shack 43-3557 Bedienungsanleitung

Radio Shack

Radio Shack TAD-794 Bedienungsanleitung

Radio Shack

Radio Shack 43-329 Bedienungsanleitung

Radio Shack

Radio Shack TAD-1010 Bedienungsanleitung

Radio Shack

Radio Shack 43-5560 Bedienungsanleitung

Radio Shack

Radio Shack 2.4 GHz Digital Spread Spectrum Cordless Telephone with Caller ID/Call Waiting... Bedienungsanleitung

Radio Shack

Radio Shack ET-1125 Bedienungsanleitung

Radio Shack

Radio Shack ET-927 Bedienungsanleitung

Beliebte Schnurloses Telefon Handbücher anderer Marken

3Com

3Com NBX Bedienungsanleitung

Panasonic

Panasonic KX-TGK210HK Bedienungsanleitung

Panasonic

Panasonic KX-TCA181EX Bedienungsanleitung

BT FREESTYLE 3200 Bedienungsanleitung

AT&T

AT&T CL84102 Bedienungsanleitung

BREZZICNI

BREZZICNI CL-3622 Bedienungsanleitung

Panasonic

Panasonic KX-TG1831NZ Bedienungsanleitung

Panasonic

Panasonic KX-TG7301E Bedienungsanleitung

Sanyo

Sanyo CLT-J70 Bedienungsanleitung

Amplicomms

Amplicomms BigTel 201 Bedienungsanleitung

GE 26992 Bedienungsanleitung

AT&T

AT&T E1812B Bedienungsanleitung

Sanyo

Sanyo CLT-670 Bedienungsanleitung

GE 15432970 Bedienungsanleitung

Curtis

Curtis TC595 Bedienungsanleitung

Gigaset

Gigaset Gigaset 3000 Micro Bedienungsanleitung

Poly

Poly VVX D230 Einrichtungshandbuch

AT&T

AT&T 7625 Bedienungsanleitung