Radio Shack ET-910 Bedienungsanleitung

Cat. No. 43-1085B

OWNER’S MANUAL

900 MHz Digital Cordless Speakerphone

Please read before using this equipment.

ET-910

With Dual Keypads

43-1085.fm Page 1 Tuesday, August 17, 1999 2:31 PM

FEATURES

Radio Shack is a registered trademark used by Tandy Corporation.

Your Radio Shack ET-910 900 MHz

Digital Cordless Speakerphone With

Dual Keypads uses advanced digital

cordless telephone technology to

give you superior sound quality. It

uses the recently allocated 900 MHz

band which means less interference,

clearer sound, and greater range

than 46/49 MHz cordless tele-

phones. Its cordless operation and

dual keypads let you make or answer

calls just about anywhere in your

home or office. Its features include:

900 MHz Operation — provides bet-

ter sound and less interference than

many other cordless phones.

Digitally Encoded Signal — pre-

vents other people from picking up

your phone’s signal and listening to

your conversations.

Dual Keypads — a full setof keys on

both the ET-910’s handset and base

let you use either keypad to make

and answer calls or program its fea-

tures.

Speakerphone — lets you make or

answer calls without using the hand-

set.

10-Number Memory Dialing — lets

you store up to 10 phone numbers in

memory for easy dialing.

Security Access Protection Code

— changes each time you place the

handset on the base, to minimize the

chances of other cordless phones

using your phone line.

10 Channels — scans 10 channels

(frequency pairs used between the

base and the handset) and automat-

ically selects the one with the least

interference each time you make or

receive a call, and lets you change

the channel during a call.

Out of Range Signal — the handset

beeps to let you know when you

move out of the base’s operating

range.

Two-Way Intercom/Paging System

—lets you send a signal from the

base to the handset, or from the

handset to the base, so you can page

someone or easily locate the hand-

set when it is away from the base. If

someone answers, you can use the

ET-910 like a two-way intercom.

Any-Key Answer — lets you press

any key on the handset (except OFF)

to answer an incoming call.

Digital Volume Controls — let you

adjust the volume of the sound you

hear through the handset and the

speakerphone.

43-1085.fm Page 2 Tuesday, August 17, 1999 2:31 PM

Programmable Ringers — let you

select from four ringer types and turn

the ringer on or off from both the

handset and the speakerphone.

Handset/Base Disable — lets you

disable the ET-910’s handset or

base during a call to prevent anyone

from interrupting your call at the other

keypad.

Privacy — prevents the person on

the other end of the phone line from

hearing your conversation with

someone in the room.

Flash — sends an electronic switch-

hook signal for use with special

phone services such as call waiting.

Redial — lets you quickly dial the last

number dialed.

Touch Tone (DTMF) or Pulse Dial-

ing — lets you use your phone with

either type of dialing.

Hearing Aid Compatible — lets you

use this telephone with hearing aids

that have a T (telephone) switch.

This phone has been tested and

found to comply with all applicable

UL and FCC standards.

For your records, we recommend

you record the phone’s serial number

in the space below. The number is lo-

cated on the bottom of the base.

Serial Number:

Important:Cordless phones such as

this one require AC power to operate.

When AC power is off, you cannot

dial out or receive incoming calls us-

ing your ET-910. For this reason, the

ET-910 should not be your only tele-

phone. To be safe, you should also

have a phone that does not require

AC power to operate (not a cordless

phone) so you can still make and re-

ceive calls if there is an AC power

failure.

This symbol is intended to alert

you to the presence of uninsulat-

ed dangerous voltage within the

product’s enclosure that might be

of sufficient magnitude to consti-

tute a riskof electric shock. Do not

open the product’s case.

This symbol is intended to inform

you that important operating and

maintenance instructions are in-

cluded in the literature accompa-

nying this product.

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER OR BACK. NO USER-SERVICE-

ABLE PARTS INSIDE. REFER SERVIC-

ING TO QUALIFIED PERSONNEL.

Warning: To prevent fire or shock

hazard, do not expose this product

to rain or moisture.

CAUTION

43-1085.fm Page 3 Tuesday, August 17, 1999 2:31 PM

READ THIS BEFORE

INSTALLATION

Your telephone conforms to federal

regulations, and you can connect it to

most telephone lines. However, each

device you connect to the phone line

draws power from the phone line. We

refer to this power draw as the de-

vice’s ringer equivalence number, or

REN. The REN is on the label on the

base’s back.

If you are using more than one phone

or other device on the line, add up all

the RENs. If the total is more than

five, your phone might not ring. In ru-

ral areas, a total REN of three might

impair ringer operation. If ringer op-

eration is impaired, remove a device

from the line.

FCC STATEMENT

This telephone complies with Part 68

FCC Rules

. You must, upon re-

quest, provide the FCC Registration

Number and the REN to your phone

company. These numbers are on the

label on the base’s back.

You must not connect your phone to

any of the following:

• Coin-operated systems

• Party-line systems

• Most electronic key phone sys-

tems

Note: Your telephone operates on

standard radio frequencies, as allo-

cated by the FCC. Even though the

access protection code prevents un-

authorized use of your phone line, it

is possible for other radio units oper-

ating on similar frequencies within a

certain area to unintentionally inter-

cept your conversations and/or

cause interference. This lack of pri-

vacy can occur with any cordless

phone.

43-1085.fm Page 4 Tuesday, August 17, 1999 2:31 PM

CONTENTS

Installation ...................................................................................................... 7

Selecting a Location .................................................................................... 7

Placing the Base on a Desktop ................................................................... 7

Mounting the Base on a Wall ....................................................................... 8

Mounting on a Wall Plate ....................................................................... 8

Mounting Directly on the Wall .............................................................. 10

Preparation ................................................................................................... 12

Installing the Battery Pack ......................................................................... 12

Charging the Battery Pack ......................................................................... 12

Setting the PULSE/TONE Switch .............................................................. 14

Adjusting the Ringers ................................................................................ 14

Checking/Setting the Ringer Type ....................................................... 14

Turning On/Off the Base’s Ringer ........................................................ 15

Turning On/Off the Handset’s Ringer ................................................... 15

Operation ...................................................................................................... 16

Making/Answering Calls ............................................................................ 16

Using the Handset ............................................................................... 16

Using the Speakerphone ..................................................................... 17

Switching Between the Handset and Speakerphone ........................... 18

Using Both the Handset and Speakerphone ........................................ 18

Using REDIAL ........................................................................................... 18

Using HOLD .............................................................................................. 19

Using PRIVACY ......................................................................................... 19

Using FLASH ............................................................................................. 20

Using Tone Services on a Pulse Line ........................................................ 20

Changing Channels ................................................................................... 20

Special Features ........................................................................................... 21

Using Memory Dialing ............................................................................... 21

Storing a Number in Memory ............................................................... 21

Storing a Pause in Memory .................................................................. 22

Dialing a Stored Number ...................................................................... 22

Chain Dialing Service Numbers ........................................................... 23

Testing Stored Emergency Numbers ................................................... 23

Using the Intercom .................................................................................... 23

Paging from the Base to the Handset .................................................. 24

Paging from the Handset to the Base .................................................. 24

Using Handset/Base Disable ................................................................25

43-1085.fm Page 5 Tuesday, August 17, 1999 2:31 PM

Troubleshooting ........................................................................................... 26

Out of Range Indications ........................................................................... 29

Out of Range with No Call ................................................................... 29

Out of Range with a Call in Progress .................................................. 29

Care and Maintenance ................................................................................. 30

The FCC Wants You to Know .................................................................... 31

Lightning .................................................................................................... 31

43-1085.fm Page 6 Tuesday, August 17, 1999 2:31 PM

INSTALLATION

SELECTING A

LOCATION

You can set the ET-910’s base on a

flat surface (such as a desktop or

counter-top), mount it on a modular

jack wall plate, or mount it directly on

the wall. The base’s location affects

the phone’s range. If you have a

choice of several locations, try each

to see which one provides the best

performance.

Select a location that is:

• Near an AC outlet

• Near a telephone line jack

• Away from electrical machinery,

electrical appliances, and metal

walls or filing cabinets

• Away from wireless intercoms,

alarms, and room monitors

If the phone line jack is not a modular

jack, you must update the wiring. You

can convert the wiring yourself, using

jacks and adapters available at your

local Radio Shack store. Or, you can

let the phone company update the

wiring for you.

Notes:

• The phone company charges for

the installation of the necessary

jacks.

• The USOC number of the base-

board jack to be installed is

RJ11C.

• After you mount the phone, you

must install the battery pack and

charge it for 24 hours before you

use it the first time. See “Prepa-

ration” on Page 12.

PLACING THE BASE ON

A DESKTOP

1. Plug one end of the supplied 7-

foot modular cord into the TO

TEL LINE jack on the back of the

ET-910’s base.

2. Plug the modular cord’s other

end into a modular phone line

jack.

3. Plug the ET-910’s AC cord into a

standard AC outlet.

4. For the best reception, adjust

the base’s antenna so it stands

straight up.

TO TEL. LINE

43-1085.fm Page 7 Tuesday, August 17, 1999 2:31 PM

MOUNTING THE BASE

ON A WALL

Using the supplied mounting bracket,

you can mount the ET-910’s base on

a phone jack wall plate or directly on

the wall.

To prepare the bracket for mounting,

twist off the tabs attached to the cen-

ter of the bracket and press them se-

curely into the holes on the narrow

end of the bracket.

Mounting on a Wall Plate

1. Press the ET-910’s AC cord

under the recessed clip directly

below it on the bottom of the

phone.

2. Plug one end of the supplied 7-

inch modular cord into the TO

TEL LINE jack, then press the

cord under the other recessed

clip on the bottom of the phone.

3. Insert the tabs on the supplied

mounting bracket into the slots

on the base’s bottom. Then

press the bracket down until it

snaps into place.

TO TEL. LINE

43-1085.fm Page 8 Tuesday, August 17, 1999 2:31 PM

4. Press the AC cord into the top

and bottom grooves on the left

side of the bracket, press the

modular cord into the center

groove on the right side of the

bracket, then plug the modular

cord into the modular phone

jack.

5. Line up the keyhole slots on the

bracket with the studs on the

wall plate, then slide the base

down onto the wall plate until it

is secure.

6. Press up on the handset holder

to remove it, turn it over so its

tabbed edge faces up, then

press it back down into its slot

on the base.

7. Plug the ET-910’s AC cord into a

standard AC outlet.

8. For the best reception, adjust

the base’s antenna so it stands

straight up.

Note: If you want to remove the sup-

plied bracket after attaching it, simply

press in the tab on each side of the

bracket and lift the bracket away from

the base.

HANDSET IN USE

GHI

PRS

TONE

ABC

JKL

TUV

OPER

DEF

MNO

WXY

CHARGE

CORDLESS TELEPHONE ET-910

TONEPULSE OFFON

RINGER

43-1085.fm Page 9 Tuesday, August 17, 1999 2:31 PM

Mounting Directly on the

Wall

Using a drill (not supplied) and the

supplied screws and spacers, you

can easily mount your ET-910 direct-

ly on the wall.

1. At the desired mounting loca-

tion, drill two holes 315/16 inches

apart, one above the other.

2. Place a spacer over each screw,

then thread a screw into each

wall hole until the screw’s head

extends about 1/4inch from the

wall.

3. Press the ET-910’s AC cord

under the recessed clip directly

below it on the bottom of the

phone.

4. Plug one end of the supplied 7-

foot modular cord into the TO

TEL LINE jack, then press the

cord under the other recessed

clip on the bottom of the phone.

5. Insert the tabs on the supplied

mounting bracket into the slots

on the base’s bottom, then press

the bracket down until it snaps

into place.

315/16”

TO TEL. LINE

43-1085.fm Page 10 Tuesday, August 17, 1999 2:31 PM

Inhaltsverzeichnis

Andere Radio Shack Schnurloses Telefon Handbücher

Radio Shack

Radio Shack 43-3556 Bedienungsanleitung

Radio Shack

Radio Shack 900 MHz Digital Spread Spectrum... Bedienungsanleitung

Radio Shack

Radio Shack 43-3535 Bedienungsanleitung

Radio Shack

Radio Shack 43-3887 Bedienungsanleitung

Radio Shack

Radio Shack 43-3535 Bedienungsanleitung

Radio Shack

Radio Shack ET-3504 Bedienungsanleitung

Radio Shack

Radio Shack 2.4 GHz 2-Line Digital Spread Spectrum Cordless Phone with Call Waiting/Caller... Bedienungsanleitung

Radio Shack

Radio Shack TAD-1016 Bedienungsanleitung

Radio Shack

Radio Shack 2-Line 900 MHz Handsfree Cordless Phone Bedienungsanleitung

Radio Shack

Radio Shack 43-3856 Bedienungsanleitung

Radio Shack

Radio Shack 43-3585 Bedienungsanleitung

Radio Shack

Radio Shack 43-324 Bedienungsanleitung

Radio Shack

Radio Shack Cordless Phone Bedienungsanleitung

Radio Shack

Radio Shack 43-3824 Bedienungsanleitung

Radio Shack

Radio Shack ET-1111 Bedienungsanleitung

Radio Shack

Radio Shack ET-598 Bedienungsanleitung

Radio Shack

Radio Shack TAD-794 Bedienungsanleitung

Radio Shack

Radio Shack 43-3581 Bedienungsanleitung

Radio Shack

Radio Shack CID-927 Bedienungsanleitung

Radio Shack

Radio Shack 43-5829 Bedienungsanleitung

Radio Shack

Radio Shack 43-5560 Bedienungsanleitung

Radio Shack

Radio Shack 43-325 Bedienungsanleitung

Radio Shack

Radio Shack 43-1107 Bedienungsanleitung

Radio Shack

Radio Shack 43-3820 Bedienungsanleitung

Beliebte Schnurloses Telefon Handbücher anderer Marken

3Com

3Com NBX Bedienungsanleitung

Panasonic

Panasonic KX-TGK210HK Bedienungsanleitung

Panasonic

Panasonic KX-TCA181EX Bedienungsanleitung

BT FREESTYLE 3200 Bedienungsanleitung

AT&T

AT&T CL84102 Bedienungsanleitung

BREZZICNI

BREZZICNI CL-3622 Bedienungsanleitung

Panasonic

Panasonic KX-TG1831NZ Bedienungsanleitung

Panasonic

Panasonic KX-TG7301E Bedienungsanleitung

Sanyo

Sanyo CLT-J70 Bedienungsanleitung

Amplicomms

Amplicomms BigTel 201 Bedienungsanleitung

GE 26992 Bedienungsanleitung

AT&T

AT&T E1812B Bedienungsanleitung

Sanyo

Sanyo CLT-670 Bedienungsanleitung

GE 15432970 Bedienungsanleitung

Curtis

Curtis TC595 Bedienungsanleitung

Gigaset

Gigaset Gigaset 3000 Micro Bedienungsanleitung

Poly

Poly VVX D230 Einrichtungshandbuch

AT&T

AT&T 7625 Bedienungsanleitung