Radio Shack TAD-1016 Bedienungsanleitung

Cat. No. 43-775

OWNER’S MANUAL

Please read before using this equipment.

TAD-1016

25-Channel •Dual-Keypad

Cordless Speakerphone

High-Capacity Digital Answering System

43-775.fm Page 1 Friday, August 13, 1999 3:25 PM

RadioShack is a registered trademark used by Tandy Corporation.

This symbol is intended to alert you

to the presence of uninsulated dan-

gerous voltage within the product’s

enclosure that might be of sufficient

magnitude to constitute a risk of

electric shock. Do not open the

product’s case.

This symbol is intended to inform

you that important operating and

maintenance instructions are in-

cluded in the literature accompany-

ing this product.

READ THIS BEFORE

INSTALLATION

Your telephone conforms to federal

regulations, and you can connect it to

most telephone lines. However, each

device you connect to the phone line

draws power from the phone line. We

refer to this power draw as the de-

vice’s

ringer equivalence number

, or

REN. The REN is on the label on the

back of the base.

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER OR BACK. NO USER-SERVICE-

ABLE PARTS INSIDE. REFER SERVIC-

ING TO QUALIFIED PERSONNEL.

Warnin

: To prevent fire or shock

hazard, do not expose this product

to rain or moisture.

CAUTION !

If you are using more than one phone

or other device on the line, add up all

the RENs. If the total is more than five,

your phone might not ring and your

answering machine might not answer.

In rural areas, a total REN of three

might impair ringer operation. If ringer

operation is impaired, remove a de-

vice from the line.

FCC STATEMENT

This telephone complies with Part 68

FCC Rules

. You must, upon re-

quest, provide the FCC Registration

Number and the REN to your phone

company. These numbers are on the

label on the back of the base.

You must not connect your phone to

any of the following:

• Coin-operated systems

• Party-line systems

• Most electronic key phone sys-

tems

Note: Your telephone operates on

standard radio frequencies, as allocat-

ed by the FCC. Even though the secu-

rity access-protection code prevents

unauthorized use of your phone line, it

is possible for other radio units operat-

ing on similar frequencies within a cer-

tain area to unintentionally intercept

your conversations and/or cause inter-

ference. This lack of privacy can occur

with any cordless phone.

43-775.fm Page 2 Friday, August 13, 1999 3:25 PM

FEATURES

Your RadioShack TAD-1016 25-

Channel • Dual-Keypad Cordless

Speakerphone, High-Capacity Digital

Answering System uses advanced an-

alog cordless telephone technology to

give you superior audio quality. Its

cordless operation lets you move free-

ly around your home or office.

The TAD stores all messages on a

computer chip. This gives you ad-

vanced capabilities over tape-based

answering machines. For example,

you can delete individual messages

while the rest are saved. Because

your TAD is fully digital, there are no

tapes to bother with and no tape

mechanisms to wear out.

Its remote operation feature lets you

access your TAD from a touch-tone

phone and guides you through system

operation with voice prompts.

TELEPHONE FEATURES

Dual Ke

pads — let you use either

keypad to make and answer calls or

program the phone’s features.

Speakerphone — lets you keep your

hands free during a call.

25 Channels — lets you change to

another channel if you hear interfer-

ence.

Securit

Access-Protection Code

— minimizes the chances of other

cordless phones using your phone

line.

20-Number Memor

Dialin

— lets

you store up to 20 phone numbers in

memory (10 on the handset and 10 on

the base) for easy dialing.

Flash — sends an electronic switch-

hook signal for use with special phone

services such as Call Waiting.

Redial — lets you quickly dial the last

number dialed.

Two-Wa

Intercom — lets you send a

signal from the base to the handset, or

from the handset to the base, so you

can page someone or easily locate the

handset when itis away from the base.

If someone answers, you can use the

TAD-1016 as a two-way intercom.

Tone or Pulse Dialin

— lets you

use your phone with either type of ser-

vice.

Hearin

Aid Compatible — lets you

use this telephone with hearing aids

that have a T (telephone) switch.

TAD Features

Voice Stamp — records and an-

nounces the day and time each mes-

sage was recorded.

itall

-S

nthesized Voice —

guides you through operation of the

system.

ital Volume Control — lets you

adjust the playback volume of the

messages.

43-775.fm Page 3 Friday, August 13, 1999 3:25 PM

Pre-recorded Messages — give you

the option of using the existing outgo-

ing messages or recording your own.

Announcement Only — lets you play

an announcement for callers to hear,

without recording their messages.

Digital Message Counter —shows

the number of messages the TAD has

saved.

Remote Operation — lets you use a

touch-tone phone (or rotary phone

and pocket tone dialer) to operate the

TAD while you are away from your

home or office.

Programmable PIN — you can set a

two-digit personal identification num-

ber for secure remote operation.

Remote Answer-On — lets you call

the TAD from a remote location even

when it is not set to answer calls.

Call Screening — lets you listen as a

caller leaves a message so you can

decide whether or not to answer the

call.

Memo Recording — lets you leave

messages for yourself or others in

your home or office.

Adjustable Ring Number — lets you

set the TAD to answer after two or five

rings.

Toll-Saver — lets you avoid unneces-

sary long-distance charges when you

call by long distance to check your

messages.

Phone Pick-Up Detection — stops

recording when you pick up any

phone on the same line as the TAD,

and resets to answer the next call.

This TAD has been tested and found

to comply with all applicable UL and

FCC standards.

Important: Cordless phones such as

this one require AC power to operate.

When AC power is off, you cannot dial

out or receive incoming calls using

your TAD-1016. For this reason, the

TAD-1016 should not be your only

telephone. To be safe, you should

also have a phone that does not re-

quire AC power to operate (not a cord-

less phone) so you can still make and

receive calls if there is an AC power

failure.

For your records, we recommend you

record the TAD’s serial number here.

The number is on the base’s label.

Serial Number ________________

43-775.fm Page 4 Friday, August 13, 1999 3:25 PM

CONTENTS

Installation ............................................................................................................ 7

Selecting a Location ........................................................................................ 7

Placing the Base on a Desktop ................................................................ 7

Mounting the Base on a Wall Plate ........................................................... 8

Mounting the Base Directly on the Wall .................................................. 10

Removing the Protective Sheet .................................................................... 12

Telephone Preparation ...................................................................................... 13

Connecting and Charging the Battery Pack .................................................. 13

Setting the Dialing Mode ............................................................................... 14

Turning Off/On the Base’s Ringer ................................................................. 15

Telephone Operation ......................................................................................... 16

Making and Receiving Calls .......................................................................... 16

Using the Handset .................................................................................. 16

Using the Speakerphone ........................................................................ 16

Switching Between the Handset and Speakerphone ............................. 16

Changing the Channel .................................................................................. 17

Putting a Call on Hold ................................................................................... 17

Using the Intercom ........................................................................................ 18

Using Redial .................................................................................................. 18

Using Flash ................................................................................................... 18

Using Tone Services on a Pulse Line ........................................................... 19

Memory Dialing ............................................................................................. 19

Storing a Number in Memory .................................................................. 19

Entering a Pause .................................................................................... 20

Dialing a Stored Number ........................................................................ 21

Chain-Dialing Service Numbers ............................................................. 21

Testing Stored Emergency Numbers ...................................................... 21

TAD Operation ................................................................................................... 22

Using the Handset to Control the TAD .......................................................... 22

Setting the Number of Rings ......................................................................... 22

Setting the Remote Operation PIN ............................................................... 23

Setting the Day and Time .............................................................................. 23

Selecting an Outgoing Message ................................................................... 24

Recording an Outgoing Message ........................................................... 24

Setting the TAD to Answer Calls ................................................................... 25

Screening Calls ............................................................................................. 26

Recording a Memo ........................................................................................ 26

Playing Messages ......................................................................................... 26

Deleting Messages ....................................................................................... 28

Adjusting the TAD’s Volume .......................................................................... 28

43-775.fm Page 5 Friday, August 13, 1999 3:25 PM

Remote Operation .............................................................................................. 29

Using the Toll-Saver ...................................................................................... 29

Accessing the TAD by Remote ...................................................................... 29

Troubleshooting ................................................................................................. 31

Care and Maintenance ....................................................................................... 33

Replacing the Battery Pack ........................................................................... 34

The FCC Wants You to Know ........................................................................ 35

Lightning ........................................................................................................ 35

43-775.fm Page 6 Friday, August 13, 1999 3:25 PM

INSTALLATION

SELECTING A

LOCATION

You can set the TAD-1016’s base on

a flat surface (such as a desk or

counter top), or mount it on a wall

plate or directly on the wall. The

base’s location affects the phone’s

range, so if you have a choice of sev-

eral locations, try each to see which

gives the best performance.

Select a location that is:

• Near an AC outlet

• Near a modular telephone line

jack

• Away from electrical machinery,

electrical appliances, and metal

walls or filing cabinets

• Away from wireless intercoms,

alarms, and room monitors

If the phone line jack is not a modular

jack, you must update the wiring. You

can convert the wiring yourself, using

jacks and adapters available at your

local RadioShack store. Or, you can

let the phone company update the wir-

ing for you. The USOC number of the

jack to be installed is RJ11C.

Placing the Base on a

Desktop

1. Plug one end of the supplied mod-

ular cord into the TEL LINE jack on

the back of the base.

2. Plug the modular cord’s other end

into a modular phone line jack.

3. Insert the supplied AC adapter’s

barrel plug into the DC IN 9V jack

on the back of the base.

43-775.fm Page 7 Friday, August 13, 1999 3:25 PM

4. Route the adapter’s cord through

the strain relief slot on the back of

the base.

5. Plug the adapter into a standard

AC outlet. The POWER indicator

on the base lights.

6. Fully extend the base’s antenna

and place it in a vertical position.

Mounting the Base

on a Wall Plate

To make this connection, you need a

short modular cord such as Ra-

dioShack Cat. No. 279-390 (not sup-

plied).

1. Plug one end of the modular cord

into the TEL LINE jack on the back

of the base.

Strain Relief Slot

43-775.fm Page 8 Friday, August 13, 1999 3:25 PM

2. Plug the supplied AC adapter’s

barrel plug into the DC IN 9V jack.

3. Route the adapter cord through

the upper and lower grooves and

the modular cord through only the

upper groove on the bottom of the

base.

4. Plug the modular cord’s other end

into the wall plate jack, then align

the base’s keyhole slots with the

wall plate studs and slide the base

downward to secure it.

5. Plug the adapter into a standard

AC outlet. The POWER indicator

on the base lights.

6. Press and lift out the handset

holder, rotate it 180°, then snap it

back into place so it holds the

handset.

Upper

Grooves

Lower

Groove

43-775.fm Page 9 Friday, August 13, 1999 3:25 PM

7. Fully extend the base’s antenna

and raise it to a vertical position.

Mounting the Base

Directly on the Wall

To mount the base directly on the wall,

you need two wood screws (not sup-

plied) with heads that fit into the key-

hole slots on the bottom of the base.

1. Drill two holes 315/16

inches apart. Then

thread a screw into

each hole, letting

the heads extend

about

5/16 inch from

the wall.

2. Plug one end of the modular cord

into the TEL LINE jack on the back

of the base.

3. Plug the supplied AC adapter’s

barrel plug into the DC IN 9V jack.

4. Route the adapter and modular

cords through the upper and lower

grooves on the bottom of the

base.

315/16

5/16

Upper

Grooves

Lower

Grooves

43-775.fm Page 10 Friday, August 13, 1999 3:25 PM

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Radio Shack Schnurloses Telefon Handbücher

Radio Shack

Radio Shack ET-539 Bedienungsanleitung

Radio Shack

Radio Shack ET-916 Bedienungsanleitung

Radio Shack

Radio Shack 43-5560 Bedienungsanleitung

Radio Shack

Radio Shack 900 MHz Digital Spread Spectrum Cordless... Bedienungsanleitung

Radio Shack

Radio Shack ET-1126 Bedienungsanleitung

Radio Shack

Radio Shack ET-917 Bedienungsanleitung

Radio Shack

Radio Shack 900 MHz Digital Spread Spectrum Cordless Phone with Digital Answerer and Caller ID/Call Waiting... Bedienungsanleitung

Radio Shack

Radio Shack ET-908 Bedienungsanleitung

Radio Shack

Radio Shack ET-545 Bedienungsanleitung

Radio Shack

Radio Shack 43-3871 Bedienungsanleitung

Radio Shack

Radio Shack Digital Answering System with Caller ID Deluxe and 2.4 GHz Digital Spread Spectrum Cordless... Bedienungsanleitung

Radio Shack

Radio Shack ET-557 Bedienungsanleitung

Radio Shack

Radio Shack 43-325 Bedienungsanleitung

Radio Shack

Radio Shack 43-324 Bedienungsanleitung

Radio Shack

Radio Shack 43-142 Bedienungsanleitung

Radio Shack

Radio Shack ET-1112 Bedienungsanleitung

Radio Shack

Radio Shack TAD 1130 Bedienungsanleitung

Radio Shack

Radio Shack 43-329 Bedienungsanleitung

Radio Shack

Radio Shack ET-1124 Bedienungsanleitung

Radio Shack

Radio Shack 43-3580 Bedienungsanleitung

Radio Shack

Radio Shack 43-3856 Bedienungsanleitung

Radio Shack

Radio Shack 43-5829 Bedienungsanleitung

Radio Shack

Radio Shack ET-1118 Bedienungsanleitung

Radio Shack

Radio Shack 43-1107 Bedienungsanleitung

Beliebte Schnurloses Telefon Handbücher anderer Marken

3Com

3Com NBX Bedienungsanleitung

Panasonic

Panasonic KX-TGK210HK Bedienungsanleitung

Panasonic

Panasonic KX-TCA181EX Bedienungsanleitung

BT FREESTYLE 3200 Bedienungsanleitung

AT&T

AT&T CL84102 Bedienungsanleitung

BREZZICNI

BREZZICNI CL-3622 Bedienungsanleitung

Panasonic

Panasonic KX-TG1831NZ Bedienungsanleitung

Panasonic

Panasonic KX-TG7301E Bedienungsanleitung

Sanyo

Sanyo CLT-J70 Bedienungsanleitung

Amplicomms

Amplicomms BigTel 201 Bedienungsanleitung

GE 26992 Bedienungsanleitung

AT&T

AT&T E1812B Bedienungsanleitung

Sanyo

Sanyo CLT-670 Bedienungsanleitung

GE 15432970 Bedienungsanleitung

Curtis

Curtis TC595 Bedienungsanleitung

Gigaset

Gigaset Gigaset 3000 Micro Bedienungsanleitung

Poly

Poly VVX D230 Einrichtungshandbuch

AT&T

AT&T 7625 Bedienungsanleitung