ResMed AirFit N30i Bedienungsanleitung

English

Français

Español

Português

User guide

QuietAir

USER GUIDE

English 1

ENGLISH

Elbow

P30i pillows cushion

Elbow ring

Vent

Headgear

QuietAir vent (removable)

Frame

Side buttons

N30i nasal cushion

Sleeve

Intended use

The AirFit N30i and AirFit P30i masks are intended to be used by patients

weighing more than 66 lb (30 kg) who have been prescribed non-invasive

positive airway pressure (PAP) therapy such as CPAP or bi-level therapy.

The masks are intended for single patient re-use in the home and

multi-patient re-use in the hospital/institutional environment.

Please read the entire guide before use.

Before using your mask

Remove all packaging and inspect each mask component for visible

deterioration.

Use the fitting template to assist in selecting the right size cushion and

frame.

Fitting your mask

1. Pull the frame and headgear over your head until the elbow is

positioned on top and the headgear is behind your head.

2. Place the cushion under your nose.

For the AirFit P30i mask, align the pillows into your nostrils.

3. Tighten or loosen the headgear until the cushion fits comfortably

under your nose.

4. Squeeze the side buttons on the elbow and detach from the frame.

Connect the air tubing from your device to the elbow, then reattach to

the frame.

Adjusting your mask

•When using the mask, air will flow out of the vents in the cushion and

elbow. If air leaks from the side or top of the cushion, adjust the mask

fitting to improve the seal.

•You can position the top of the frame forward or backwards over your

head until the mask feels comfortable.

English 3

Sizing the mask frame

If the mask frame falls back over your head or sits too close to your ears,

try a small frame size. If the mask falls forward on your head or sits too

close to your eyes, try a standard frame size.

Disassembling your mask for cleaning

If your mask is connected to a device, disconnect the device air tubing

from the mask elbow.

1. Pull the cushion from the frame.

2. Undo the fastening tabs on the headgear strap and pull it from the

frame.

3. Squeeze the side buttons on the elbow and detach from the frame.

Note: For the AirFit P30i mask, the QuietAir vent can be removed to allow

inspection of the vent holes.

Cleaning your mask

After each use: Cushion

Weekly: Headgear, frame and elbow

1. Soak the components in warm water with a mild liquid detergent.

Ensure that there are no air bubbles while soaking.

2. Hand wash the components with a soft bristle brush. Pay particular

attention to the vent holes.

3. Thoroughly rinse the components under running water.

4. For the frame sleeves, squeeze with a clean towel to remove excess

water. For the AirFit P30i mask, shake the QuietAir vent to remove

any excess water. Leave the components to air dry out of direct

sunlight.

If the mask components are not visibly clean, repeat the cleaning steps.

Reassembling your mask

1. Connect the elbow into the top of the frame until it clicks.

2. Insert the headgear strap into the frame and fold the fastening tabs

backwards.

3. Insert the ends of the frame into the cushion, ensuring that the arrows

on the cushion and frame are aligned.

Note:

•If the elbow ring detaches, re-insert into the top of the frame.

•If the QuietAir vent is removed from the AirFit P30i mask, reinsert it

into the cushion.

WARNING

•The mask is not suitable for patients requiring life support ventilation.

•To avoid affecting the safety and quality of therapy, the mask vents must be kept clear

to protect against rebreathing. Regularly inspect the vents to ensure they are kept

clean, undamaged and clear of blockages.

•The mask must be used under qualified supervision for patients who are unable to

remove the mask by themselves. The mask may not be suitable for those prone to

aspiration.

•Regularly clean your mask to maintain the quality of your mask and to prevent the

growth of germs that can adversely affect your health.

•Visual criteria for product inspection: If there is any visible deterioration of a mask

component (cracking, crazing, tears etc.), the component should be discarded and

replaced.

•Only use compatible CPAP or bi-level therapy devices. The technical specifications of

the mask are provided for healthcare professionals to determine compatible devices.

Use with incompatible devices may affect the performance or safety of the mask.

English 5

WARNING

•Discontinue using the mask if you have ANY adverse reaction and consult your

physician or sleep therapist.

•The mask is not intended to be used simultaneously with nebulizer medications that

are in the air path of the mask/tube.

CAUTION

•Remove all packaging before using the mask.

•Using a mask may cause tooth, gum or jaw soreness or aggravate an existing dental

condition. If symptoms occur, consult your physician or dentist.

•When fitting the mask, do not overtighten the headgear as this may lead to skin

redness or sores around the mask cushion.

•The mask should not be used unless the device is turned on. Once the mask is fitted,

ensure the device is blowing air to reduce risk of rebreathing exhaled air.

•As with all masks, some rebreathing may occur at low pressures.

•Always follow cleaning instructions and only use a mild liquid detergent. Some

cleaning products may damage the mask, its parts and their function, or leave harmful

residual vapours. Do not use a dish washer or washing machine to clean the mask.

•Do not iron the headgear as the material is heat sensitive and will be damaged.

Technical specifications

Compatible devices

For a full list of compatible devices for this mask, see the Mask/Device Compatibility List

at ResMed.com/downloads/masks.

Pressure-flow curve:

Pressure

(cm H

Flow

(L/min)

AirFit N30i

AirFit P30i

Mask setting options:

For AirSense, AirCurve or S9

Therapy Pressure:

Pillows

4 to 25 cm H

Pillows

4 to 25 cm H

Resistance: Drop in pressure measured (nominal)

at 50 L/min

0.4 cm H

at 100 L/min

1.7 cm H2O

1.5 cm H2O

Sound: Declared dual-number noise emission values in accordance with ISO4871:1996

and ISO3744:2010. A-weighted sound power level and A-weighted sound pressure level at

a distance of 1 m, with uncertainty of 3 dBA, are shown

Sound power level

Sound pressure level

24 dBA

17 dBA

21 dBA

14 dBA

Environmental conditions:

Operating temperature: 41°F to 104°F (5°C to 40°C)

Operating humidity: 15% to 95% non-condensing

Storage and transport temperature: -4°F to 140°F (-20°C to +60°C)

Storage and transport humidity: up to 95% non-condensing

Service life: The service life of the mask system is dependent on the intensity of usage,

maintenance, and environmental conditions to which the mask is used or stored. As this

mask system and its components are modular in nature, it is recommended that the user

maintain and inspect it on a regular basis, and replace the mask system or any

components if deemed necessary or according to the ‘Visual criteria for product inspection’

in the ‘Warning’ section of this guide.

Note: The manufacturer reserves the right to change these specifications without notice.

Storage

Ensure that the mask is thoroughly clean and dry before storing it for any length of time.

Store the mask in a dry place out of direct sunlight.

Disposal

This mask does not contain any hazardous substances and may be disposed of with your

normal household refuse.

Reprocessing the mask between patients

Only Sleep Lab Mask (SLM) variants of the mask system are intended for multi-patient

re-use. When using between patients, these masks must be reprocessed according to

cleaning and disinfection instructions available on ResMed.com/downloads/masks.

English 7

Symbols

The following symbols may appear on your product or packaging:

Nasal cradle mask

Nasal pillows mask

QuietAir vent

Device setting - Pillows

Cushion size - small

Cushion size - medium

Cushion size - large

Cushion size - wide

Cushion size - small wide

Standard frame

Small frame

This product is not made with natural rubber latex.

Caution, consult accompanying documents.

See symbols glossary at ResMed.com/symbols.

Limited Warranty

ResMed Ltd (ResMed) warrants that your ResMed mask system

(including mask frame, cushion, headgear and elbow) will be free from

defects in material and workmanship from the date of purchase for 90

days, or in the case of disposable masks and disposable mask

components for 7 days. This warranty is only available to the initial

consumer. It is not transferable. If the product fails under conditions of

normal use, ResMed will repair or replace, at its option, the defective

product or any of its components. This limited warranty does not cover:

a) any damage caused as a result of improper use, abuse, modification or

alteration of the product; b) repairs carried out by any service organization

that has not been expressly authorized by ResMed to perform such

repairs; and c) any damage or contamination due to cigarette, pipe, cigar

or other smoke. Warranty is void on product sold, or resold, outside the

region of original purchase.

Andere Handbücher für AirFit N30i

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ResMed Medizinische Geräte Handbücher

ResMed

ResMed S8 AutoScore II Bedienungsanleitung

ResMed

ResMed AIRCurve 10 S Bedienungsanleitung

ResMed

ResMed Swift FX Bedienungsanleitung

ResMed

ResMed AIRMINI Bedienungsanleitung

ResMed

ResMed AirSense 10 Leitfaden

ResMed

ResMed Flow Generator AutoSet CS 2 Bedienungsanleitung

ResMed

ResMed AutoSet S9 Series Bedienungsanleitung

ResMed

ResMed VPAP Auto Bedienungsanleitung

ResMed

ResMed NV Elbow F20 Bedienungsanleitung

ResMed

ResMed AirFit P10 Bedienungsanleitung

ResMed

ResMed Ultra Mirage Bedienungsanleitung

ResMed

ResMed AirSense11 Bedienungsanleitung

ResMed

ResMed Swift LT Bedienungsanleitung

ResMed

ResMed Mobi Bedienungsanleitung

ResMed

ResMed AIRMINI Bedienungsanleitung

ResMed

ResMed Mirage FX Bedienungsanleitung

ResMed

ResMed VPAP III ST-A Bedienungsanleitung

ResMed

ResMed AirFit N20 Bedienungsanleitung

ResMed

ResMed airsense 10 autoset Montageanleitung

ResMed

ResMed CPAP Bedienungsanleitung

ResMed

ResMed stellar series Bedienungsanleitung

ResMed

ResMed ResScan Bedienungsanleitung

ResMed

ResMed AirSense 10 Bedienungsanleitung

ResMed

ResMed Sullivan Comfort Bedienungsanleitung

Beliebte Medizinische Geräte Handbücher anderer Marken

TekTone

TekTone Tek-CARE160 Bedienungsanleitung

NeuroMetrix

NeuroMetrix Quell 2.0 Bedienungsanleitung

AMT

AMT XLR8 Bedienungsanleitung

EDAN

EDAN SONOTRAX Pro Bedienungsanleitung

Restorative Therapies

Restorative Therapies RT300 Bedienungsanleitung

Gendex

Gendex Expert DC Bedienungsanleitung

Dexcowin

Dexcowin ADX4000W Bedienungsanleitung

Libelium

Libelium MySignals Bedienungsanleitung

Acelity

Acelity V.A.C.ULTA 4 Bedienungsanleitung

Caputron

Caputron ActivaDose II tDCS Bedienungsanleitung

Plinth 2000

Plinth 2000 93CDT Bedienungsanleitung

GE SENOGRAPHE 800T Bedienungsanleitung

GE Definium 5000 Bedienungsanleitung

Kanmed

Kanmed GE-1380 Bedienungsanleitung

Huntleigh

Huntleigh FD1 Bedienungsanleitung

Stryker

Stryker SPR Plus Bedienungsanleitung

Tobii Dynavox

Tobii Dynavox I-Series Bedienungsanleitung

S-Capepod

S-Capepod Evac Cocoon Bedienungsanleitung