ResMed Astral 150 Bedienungsanleitung

Quick start guide

English

Read your entire Astral™User Guide or Clinical Guide before use.

The Astral device

1. Adapter port

Can be fitted with single

limb adapter, single limb

leak adapter or double limb

adapter (Astral 150 only)

2. Handle

3. Inspiratory port (to patient)

4. Ethernet connector

(service use only)

5. USB connector

(for download to ResScan

and connection of

approved accessories)

6. Mini USB connector for

ResMed Connectivity

Module (RCM) or ResMed

Connectivity Module

Hospital (RCMH)

7. DC power inlet

8. Device on/off push button

9. SpO2Sensor connector

10.Remote alarm five pin

connector

11. Low flow oxygen input

(up to 30L/min)

12.Air inlet

(complete with

hypoallergenic filter)

Note: Some accessories may

not be available in all regions.

4 5 6 7 8

9101112

The Astral device interface

1. Touch screen

2. Power source indicators

AC (mains power supply)

DC (external battery, car

accessory adapter or

ResMed Power Station II)

Internal battery

3. Therapy on/off indicator

Device ready

Constant green display when

the device is turned on but

not ventilating.

Device ventilating

Flashes blue when the

device is ventilating and the

Ventilation LED setting is

‘ON’. Otherwise is ‘OFF’

4. Alarm mute/reset button

Illuminates when an alarm is

triggered and flashes when

the sound is muted.

5. Alarm bar

Touch screen

1. Clinical mode access button

Locked Unlocked

2. Manual breath

button only shown

if enabled

3. Information bar

4. Internal battery indicator

5. Lock touch screen button

6. Menu bar

7. Bottom bar

Start ventilation button

Stop ventilation button

9. Main screen

10.Sub menus

11. Pressure bar

Patient circuits

The Astral device supports single and double limb circuits with the use of interchangeable circuit

adapters.

Breathing circuits may be of 10, 15 or 22 mm diameter. For recommended patient circuit

components and compatible accessories, refer to www.resmed.com/astral/circuits.

There are three circuit adapters:

Adapter For use with

1. Single limb

leak

Single limb circuit with intentional

leak

or Mouthpiece circuit

2. Single limb Single limb circuit with expiratory

valve (expiratory valve integrated

into the circuit)

3. Double limb

(Astral 150

only)

Double limb circuit (expiratory valve

integrated into the adapter) OR

single limb circuit with intentional

leak

or Mouthpiece circuit

Fitting the circuit adapter

Before connecting the patient circuit, the adapter specific to the required circuit type must be fitted.

To fit the adapter:

1. Turn over the device and place

on a soft surface (to protect

the LCD screen).

2. Press and hold the eject

button. Pull the cover out

towards you.

3. Lift the adapter out of the

socket.

4. Replace with the new adapter,

ensuring it sits firmly in the

socket.

5. Place the cover over the

enclosure, ensuring the

runners on the device and the

cover are aligned. Slide the

cover back into place until the

latch clicks.

Setting up the circuit

For complete details on setting up the circuit see Assembling patient circuits in the Astral Clinical

Guide.

Single limb circuit with intentional leak or

Mouthpiece circuit

Single limb circuit with expiratory valve

using ResMed proprietary circuit

Single limb circuit with expiratory valve

using standard circuit

Double limb circuit (Astral 150 only) or

single limb circuit with intentional leak and

Mouthpiece circuit

To patient

Performing a Learn Circuit

Do not connect patient interfaces prior to

performing the Learn Circuit.

1. From the Setup menu, select the Circuit

sub menu.

2. Press Start and follow the on-screen

prompts.

A Results screen is displayed once Learn

Circuit is complete. Error codes are provided

if Learn Circuit fails and can be found in the

Clinical Guide for help with troubleshooting.

The previous test results can be accessed by

selecting the Results button in the Circuit sub

menu.

Powering on the device

To power on the device, simply press the

green power on/off switch at the back of

the device. The device will perform a system

check.

On completion of the system check, the

Patient Home screen and active program is

displayed.

If more than one program displays, the active

program will be highlighted orange.

Note: Settings configured in the active

program will be used when ventilation is

started.

Accessing Clinical mode

To access Clinical mode:

Clinical mode can be accessed from any

screen, whether or not the Astral device is

ventilating.

1. From the patient home screen, press

and hold for 3 seconds.

2. Select 20 minutes or Unlimited.

The padlock is unlocked and the Main

Settings screen is displayed.

To exit Clinical mode:

1. Press . The Exit Clinical Mode screen

is displayed.

2. Press Confirm. The padlock is locked and

the Patient Home screen is displayed.

Note: If you do not make a selection within 7

seconds, the device returns to the previous

screen.

Using the Setup Assistant

To quickly set up the Astral device and

start ventilation for a new patient, use the

Setup Assistant.

1. Access Clinical mode.

2. From the main menu, press .

3. Select SetupAssistant and press

Start.

4. A warning message will display. Select

Continue.

5. Select the patient type to automatically

configure alarm and setting ranges.

6. Select the circuit type to be connected.

7. Select Start to run the Learn Circuit.

8. Follow the on-screen prompts to attach

and test the circuit.

9. Select your required ventilation mode.

The default settings for the mode are

displayed.

10.Review and adjust the settings as

required.

11. Press to start ventilation.

For further information on adjusting

setting parameters and alarm settings, see

Adjusting patient settings and Adjusting

alarm settings in the Astral Clinical Guide.

Navigating the menus

Monitors

Waveforms Displays the last 15 seconds of patient

airway pressure and ﬂow in a graph. The

graph updates in real-time.

Monitoring Displays all measured parameters in

numerical form.

Trends Displays trending of various parameters

for the last 30 days.

Setup

Programs*

Setup Assistant*

Circuit

Settings Main Settings

Manual Breath

Sigh Breath

USB Patient Data

Settings

Upgrade**

Device Conﬁg. Device

Date / Time

Units

Patient access

Alarms

Alarm 1 & 2 Tidal Volume (Vt)

Minute Ventilation (Mv)

Respiratory Rate

Pressure

Low PEEP

Ventilation Stop

Leak

NV mask / Rebreathing

Alarm 3 FiO2

SpO2

Pulse

Apnoea

Response

Apnoea Response

Apnoea Detection

Alarm Volume Alarm Level

Alarm Minimum Volume

Alarm Test

Disconnection

Alarm

Disconnection Alarm

Information

Events Alarms

Settings

System

Delete*

Device Basic

Advanced

Battery Charge

Maintenance

*Available in Clinical mode only. **Software upgrades can only be performed by an authorised service representative. Astral has the ability to

be upgraded with a USB stick containing the appropriate software. Please contact your authorised agent for further information.

Enabling additional programs

The Astral device comes factory preset

with one active program. Additional

programs can be enabled.

1. Access Clinical mode.

2. From the Setup main menu, select

Programs.

3. Enable additional programs by pressing

the slider.

Note: The current active program is

highlighted in orange and cannot be

disabled.

4. Rename the program by pressing the

Rename button.

Within the Rename window, a name

for the current active program can be

chosen from the list provided (eg, DAY).

Note: A selected name can be removed

by pressing the delete button .

5. When selected, the program name is

displayed on the program label and on

the information bar when that program

is active.

Enabling additional programs

The Astral device comes factory preset

with one active program. Additional

programs can be enabled.

1. Access Clinical mode.

2. From the Setup main menu, select

Programs.

3. Enable additional programs by pressing

the slider.

Note: The current active program is

highlighted in orange and cannot be

disabled.

4. Rename the program by pressing the

Rename button.

Within the Rename window, a name

for the current active program can be

chosen from the list provided (eg, DAY).

Note: A selected name can be removed

by pressing the delete button .

5. When selected, the program name is

displayed on the program label and on

the information bar when that program

is active.

Enabling the ‘Big buttons’ mode

The Astral device offers an enhanced

access feature (‘Big buttons’ mode) to

provide easier usability and accessibility for

starting and stopping ventilation as well as

Alarm mute.

The ‘Big buttons’ mode can be switched

on and off as required in either Clinical or

Patient mode.

1. From the main menu, press .

2. Select the Patient Access tab from the

Device Config. menu.

3. Move the Big buttons slider to On.

Your enhanced access feature is now

enabled.

Andere Handbücher für Astral 150

Inhaltsverzeichnis

Andere ResMed Medizinische Geräte Handbücher

ResMed

ResMed VPAP Auto Bedienungsanleitung

ResMed

ResMed H5i Technisches Handbuch

ResMed

ResMed S8 ESCAPE S8 Bedienungsanleitung

ResMed

ResMed ResLink Bedienungsanleitung

ResMed

ResMed VPAP ST Technisches Handbuch

ResMed

ResMed Ultra Mirage Bedienungsanleitung

ResMed

ResMed Ultra Mirage Bedienungsanleitung

ResMed

ResMed Mirage Quattro Bedienungsanleitung

ResMed

ResMed AirFit N30i Bedienungsanleitung

ResMed

ResMed Narval CC Bedienungsanleitung

ResMed

ResMed AirFit N30i Bedienungsanleitung

ResMed

ResMed Lumis HFT Bedienungsanleitung

ResMed

ResMed AutoSet CS-A Bedienungs- und Sicherheitshinweise

ResMed

ResMed ApneaLink Bedienungsanleitung

ResMed

ResMed airsense 10 autoset Bedienungsanleitung

ResMed

ResMed Elisee 150 Bedienungsanleitung

ResMed

ResMed Ultra Mirage II Bedienungsanleitung

ResMed

ResMed ELITE S8 Bedienungsanleitung

ResMed

ResMed Ultra Mirage II Bedienungsanleitung

ResMed

ResMed VPAP ST Bedienungsanleitung

ResMed

ResMed AirFit N20 Classic Bedienungsanleitung

ResMed

ResMed Mirage SoftGel Bedienungsanleitung

ResMed

ResMed Mirage Swift Bedienungsanleitung

ResMed

ResMed AirFit F10 Bedienungsanleitung

Beliebte Medizinische Geräte Handbücher anderer Marken

TekTone

TekTone Tek-CARE160 Bedienungsanleitung

NeuroMetrix

NeuroMetrix Quell 2.0 Bedienungsanleitung

AMT

AMT XLR8 Bedienungsanleitung

EDAN

EDAN SONOTRAX Pro Bedienungsanleitung

Restorative Therapies

Restorative Therapies RT300 Bedienungsanleitung

Gendex

Gendex Expert DC Bedienungsanleitung

Dexcowin

Dexcowin ADX4000W Bedienungsanleitung

Libelium

Libelium MySignals Bedienungsanleitung

Acelity

Acelity V.A.C.ULTA 4 Bedienungsanleitung

Caputron

Caputron ActivaDose II tDCS Bedienungsanleitung

Plinth 2000

Plinth 2000 93CDT Bedienungsanleitung

GE SENOGRAPHE 800T Bedienungsanleitung

GE Definium 5000 Bedienungsanleitung

Kanmed

Kanmed GE-1380 Bedienungsanleitung

Huntleigh

Huntleigh FD1 Bedienungsanleitung

Stryker

Stryker SPR Plus Bedienungsanleitung

Tobii Dynavox

Tobii Dynavox I-Series Bedienungsanleitung

S-Capepod

S-Capepod Evac Cocoon Bedienungsanleitung