ResMed ClimateLineAir Oxy Bedienungsanleitung

User guide

English

User guide

English 1

ENGLISH

About your ClimateLineAir

The ClimateLineAir™is heated air tubing that delivers the

desired temperature at your mask. ClimateLineAir Oxy is a

variant of the ClimateLineAir that has a built-in oxygen

connector to attach a supplemental oxygen supply.

When used with the HumidAir™humidifier, ClimateLineAir

heated air tubing allows you to use Climate Control. Climate

Control is designed to make therapy more comfortable by

enabling constant temperature and maintaining humidity.

The ClimateLineAir heated air tubing is designed for use with

AirSense™10 / AirCurve™10 and Lumis™devices. Please read

this entire user guide together with your device user guide

before using your ClimateLineAir heated air tubing.

Note:

•Not all types of air tubing are available in all regions.

•Lumis does not include S9 Lumis Tx.

Setup

1. Make sure the device is connected and turned on.

2. Hold the cuff of the air tubing and line up the air tubing

connector with the connector port.

3. Push the cuff until the connector clicks into place.

ClimateLineAir connected will briefly display on the

device screen.

4. Connect the assembled mask to the free end of the air

tubing.

Setup with supplemental oxygen

To set up the ClimateLineAir Oxy with supplemental oxygen,

perform the steps outlined in the setup section and the

following additional steps.

1. Remove the cap from the oxygen connector.

2. Connect the oxygen supply tubing to the oxygen

connector.

Make sure it is firmly attached.

English 3

Notes:

•Before adding oxygen, familiarize yourself with the specific

warnings relating to the use of supplemental oxygen.

These can be found at the end of your device User Guide.

•If you use the ClimateLineAir Oxy without supplemental

oxygen, make sure the cap of the oxygen connector is

firmly attached.

Climate Control

Climate Control is an intelligent system that controls the

humidifier and the ClimateLineAir heated air tubing to deliver

constant, comfortable temperature and humidity levels during

therapy.

Designed to prevent dryness of the nose and mouth, it

maintains the set temperature and relative humidity while you

sleep. Climate Control can be set to either Auto or Manual

and is only available when both the ClimateLineAir and the

HumidAir humidifier are attached.

Climate Control Auto

Climate Control Auto is the recommended and default setting.

Climate Control Auto is designed to make therapy as easy as

possible, so there is no need to change the temperature or

humidity settings.

The Tube Temperature is set to Auto (80°F [27°C]) and

Climate Control adjusts the humidifier output to maintain a

constant, comfortable humidity level of 85% relative humidity

while protecting against rainout (water droplets in the air

tubing and mask).

Tube Temperature

In Climate Control Auto there is no need to change any

settings, but if the air in the mask feels too warm or cold you

can adjust the tube temperature to find what is most

comfortable for you. You can set the Tube Temperature to

anywhere between 60–86°F (16–30°C), or turn it off

completely.

To adjust the Tube Temperature:

1. In My Options, turn the dial to highlight Tube Temp.and

then press the dial.

2. Turn the dial to adjust the temperature and press the dial

to save the change.

Climate Control Manual

Designed to offer you more flexibility and control over your

settings, Climate Control Manual lets you adjust the

temperature and humidity to the setting which is most

comfortable for you.

In Climate Control Manual, the tube temperature and the

humidity level can be set independently however, rainout

protection is not guaranteed. If rainout does occur, first try

increasing the tube temperature. If the air temperature

becomes too warm and rainout continues, try decreasing the

humidity.

To change to Climate Control Manual:

1. In My Options, turn the dial to highlight Climate Ctrl and

then press the dial.

2. Turn the dial to select Manual and press the dial to save

the change.

Humidity Level

The humidifier moistens the air and is designed to make

therapy more comfortable. If you are getting a dry nose or

mouth, turn up the humidity. If you are getting any moisture

in your mask, turn down the humidity.

You can set the Humidity Level to Off or between 1 and 8,

where 1 is the lowest humidity setting and 8 is the highest

humidity setting.

English 5

To adjust the Humidity Level:

1. In My Options, turn the dial to highlight Humidity Level

and then press the dial.

2. Turn the dial to adjust the humidity level and press the dial

to save the change.

If you have been using Climate Control Manual and want to

return to Climate Control Auto, follow the instructions below.

To change to Climate Control Auto:

1. In My Options, turn the dial to highlight Climate Ctrl and

then press the dial.

2. Turn the dial to select Auto and then press the dial to save

the change.

Caring for your ClimateLineAir

It is important that you regularly clean your air tubing to make

sure you receive optimal therapy. The following sections will

help you with disconnecting, cleaning, checking and

reconnecting your air tubing.

Disconnecting

1. Hold the cuff of the air tubing, apply gentle pressure to the

release buttons and pull it away from the device.

2. Hold both the cuff of the air tubing and the swivel of the

mask, then gently pull apart.

Note: Only hold and pull the cuff of the air tubing. Do not hold

or pull the tubing itself as it may cause damage.

Cleaning

You should clean the air tubing weekly as described.

1. Wash the air tubing in warm water using mild detergent.

Do not wash in a dishwasher or washing machine.

2. Rinse the air tubing thoroughly and allow to dry, out of

direct sunlight and/or heat.

Checking

You should regularly check the air tubing for any damage. If

there are any holes, tears or cracks you should replace it.

Reconnecting the air tubing

When the air tubing is dry, you can reconnect it to the device.

1. Connect the air tubing firmly to the air outlet located on

the rear of the device.

2. Connect the free end of the air tubing firmly onto the

assembled mask.

English 7

Troubleshooting

If you have any problems, refer to the troubleshooting section

of your device user guide or www.resmed.com.

Technical specifications

Environmental conditions

Operating temperature:

+41°F to +95°F (+5°C to +35°C)

Note: The air flow for breathing

produced by this therapy device can

be higher than the temperature of

the room. Under extreme ambient

temperature conditions (104°F/40°C)

the device remains safe.

Operating humidity:

10 to 95% relative humidity, non-

condensing

Operating altitude:

Sea level to 8,500' (2,591 m); air

pressure range 1013 hPa to 738 hPa

Storage and transport temperature:

-4°F to +140°F (-20°C to +60°C)

Storage and transport humidity:

5 to 95% relative humidity, non-

condensing

Electromagnetic compatibility

Refer to the device User Guide.

Temperature

Temperature range:

+60 to +86°F (+16 to +30°C)

Cut-out:

+106°F (+41°C)

Operating pressure range

Maximum recommended pressure

30 cm H

O (30 hPa)

Physical

Air tubing

Material

Length

Inner

diameter

ClimateLineAir Flexible plastic and

electrical components

6'6" (2 m) 0.6" (15 mm)

ClimateLineAir

Oxy

Flexible plastic and

electrical components

6'4" (1.9 m)

0.75" (19 mm)

Design life

Air tubing: Standard, SlimLine,

ClimateLineAir, ClimateLineAir Oxy

6 months

Symbols

The following symbols may appear on the product or

packaging.

Manufacturer. European Authorized

Representative. Catalog number. Batch code.

Prescription only (In the US, Federal law restricts

these devices to sale by or on the order of a physician).

Humidity limitation. Temperature limitation. China

pollution control logo 1. China pollution control logo 2.

Environmental information

This device should be disposed of separately, not as unsorted

municipal waste. To dispose of your device, you should use

appropriate collection, reuse and recycling systems available

in your region. The use of these collection, reuse and

recycling systems is designed to reduce pressure on natural

resources and prevent hazardous substances from damaging

the environment.

If you need information on these disposal systems, please

contact your local waste administration. The crossed-bin

symbol invites you to use these disposal systems. If you

require information on collection and disposal of your ResMed

device please contact your ResMed office, local distributor or

go to www.resmed.com/environment.

Limited warranty

Refer to your device user guide.

ResMed.com

378457

ResMed Ltd

1 Elizabeth Macarthur Drive Bella Vista NSW 2153 Australia

See www.resmed.com for other ResMed locations worldwide. For patent and other intellectual

property information, see www.resmed.com/ip. AirSense, AirCurve, ClimateLine, HumidAir and Lumis

are trademarks of ResMed Ltd. ClimateLine is registered in U.S. Patent and Trademark Office.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ResMed Medizinische Geräte Handbücher

ResMed

ResMed AirFit F10 Bedienungsanleitung

ResMed

ResMed Swift FX Bedienungsanleitung

ResMed

ResMed airsense 10 autoset Leitfaden

ResMed

ResMed Swift LT Bedienungsanleitung

ResMed

ResMed S9 AutoSet Technisches Handbuch

ResMed

ResMed AirFit N20 Bedienungsanleitung

ResMed

ResMed H5i Technisches Handbuch

ResMed

ResMed VPAP Auto Bedienungsanleitung

ResMed

ResMed Oxygen Connector Port Bedienungsanleitung

ResMed

ResMed Quattro FX Bedienungsanleitung

ResMed

ResMed AirFit F20 Bedienungsanleitung

ResMed

ResMed ApneaLink Bedienungsanleitung

ResMed

ResMed Ultra Mirage II Bedienungsanleitung

ResMed

ResMed Mirage FX Bedienungsanleitung

ResMed

ResMed Mirage Quattro Bedienungsanleitung

ResMed

ResMed VPAP IV ST Betriebsanleitung

ResMed

ResMed S9 AutoSet Technisches Handbuch

ResMed

ResMed S8 ESCAPE System Bedienungsanleitung

ResMed

ResMed Mirage Activa Bedienungsanleitung

ResMed

ResMed Astral 150 Bedienungsanleitung

ResMed

ResMed Flow Generator AutoSet CS 2 Bedienungsanleitung

ResMed

ResMed Astral 100 Bedienungsanleitung

ResMed

ResMed S7 Lightweight Bedienungsanleitung

ResMed

ResMed Mirage Activa LT Bedienungsanleitung

Beliebte Medizinische Geräte Handbücher anderer Marken

TekTone

TekTone Tek-CARE160 Bedienungsanleitung

NeuroMetrix

NeuroMetrix Quell 2.0 Bedienungsanleitung

AMT

AMT XLR8 Bedienungsanleitung

EDAN

EDAN SONOTRAX Pro Bedienungsanleitung

Restorative Therapies

Restorative Therapies RT300 Bedienungsanleitung

Gendex

Gendex Expert DC Bedienungsanleitung

Dexcowin

Dexcowin ADX4000W Bedienungsanleitung

Libelium

Libelium MySignals Bedienungsanleitung

Acelity

Acelity V.A.C.ULTA 4 Bedienungsanleitung

Caputron

Caputron ActivaDose II tDCS Bedienungsanleitung

Plinth 2000

Plinth 2000 93CDT Bedienungsanleitung

GE SENOGRAPHE 800T Bedienungsanleitung

GE Definium 5000 Bedienungsanleitung

Kanmed

Kanmed GE-1380 Bedienungsanleitung

Huntleigh

Huntleigh FD1 Bedienungsanleitung

Stryker

Stryker SPR Plus Bedienungsanleitung

Tobii Dynavox

Tobii Dynavox I-Series Bedienungsanleitung

S-Capepod

S-Capepod Evac Cocoon Bedienungsanleitung