ROSE DISPLAYS ANOKIOSK-STACKABLE Bedienungsanleitung

The AnoKiosk™ is a trademark of Rose Displays, Ltd. Neither the

manufacturer nor any sales agent may be held liable for injury, loss or

damage resulting from the use of these products. Part

#02INAnoKioskRigidStackable

Incept-09.20.02

Instruction Sheet

Note:

We recommended that two people

assemble this kiosk.

Step 1a

Slide spine into vertical rail.

Step 1b

Slide another vertical rail onto the

other edge of spine. Repeat for all

vertical rails and spines.

Step 2

Carefully insert corner brackets into

ends of bottom rails, using thumb as

shown in illustration. Two brackets

per end of each rail. Bracket can

bend if forced.

Detail- It is important that the corner

bracket tension tab faces toward

outside of frame. (2b)

Step 3

Lay out parts as they will be configured

on the floor.

Note: One kiosk will have Base Rail

other(s) will have stacker bar.

AnoKiosk™

Instructions for Assembly

Kiosk spine Corner brackets

Parts

Single rails Split rails

(Continued on other side)

2a 2b

1a 1b

35 Congress Street, Salem, MA 01970

Tel# 1- 800 631-9707 Fax# 1-800-560-2890

e-mail:signware@rosedisplays.com

Bottom Rails

with Base Rail

3-Way

4-Way

Bottom Rails

with Stacker Bar

The AnoKiosk™ is a trademark of Rose Displays, Ltd. Neither the

manufacturer nor any sales agent may be held liable for injury, loss or

damage resulting from the use of these products. Part

#02INAnoKioskRigidStackable

Incept-09.20.02

Instruction Sheet (side 2)

Instructions for Assembly continued

AnoKiosk™

35 Congress Street, Salem, MA 01970

Tel# 1- 800 631-9707 Fax# 1-800-560-2890

e-mail:signware@rosedisplays.com

Step 4

Assemble the vertical rail assem-

blies onto the upward facing

corner brackets already inserted

into the bottom rails. All four

brackets should go into the

vertical rails at one time.

Note: (4 way only) The last

vertical rail will be tensioned.

This is normal.

Step 5

Insert corner brackets into ends

of split rails, 1 per end. Use thumb

as shown in illustration.

Step 6

Assemble split rails onto top ends

of vertical rails, one inside and

one outside of each side of the

AnoKiosk.

Step 7

Insert graphics into kiosk

with Base Rails.

Step 8

Place kiosk with stacker bar on

top of first kiosk. Line up stacker

bar with split rails on lower kiosk

and snap together.

Step 9

Load graphics into upper kiosk.

Step 10

If there are more kiosks to be

stacked repeat steps 8 and 9.

Figure 8 Figure 9

The AnoKiosk™ is a trademark of Rose Displays, Ltd. Neither the

manufacturer nor any sales agent may be held liable for injury, loss or

damage resulting from the use of these products. Part

#02INAnoKioskRigidStackable

Incept-09.20.02

Instruction Sheet

Note:

We recommended that two people

assemble this kiosk.

Step 1a

Slide spine into vertical rail.

Step 1b

Slide another vertical rail onto the

other edge of spine. Repeat for all

vertical rails and spines.

Step 2

Carefully insert corner brackets into

ends of bottom rails, using thumb as

shown in illustration. Two brackets

per end of each rail. Bracket can

bend if forced.

Detail- It is important that the corner

bracket tension tab faces toward

outside of frame. (2b)

Step 3

Lay out parts as they will be configured

on the floor.

Note: One kiosk will have Base Rail

other(s) will have stacker bar.

AnoKiosk™

Instructions for Assembly

Kiosk spine Corner brackets

Parts

Single rails Split rails

(Continued on other side)

2a 2b

1a 1b

Bottom Rails

with Base Rail

3-Way

4-Way

Bottom Rails

with Stacker Bar

The AnoKiosk™ is a trademark of Rose Displays, Ltd. Neither the

manufacturer nor any sales agent may be held liable for injury, loss or

damage resulting from the use of these products. Part

#02INAnoKioskRigidStackable

Incept-09.20.02

Instruction Sheet (side 2)

Instructions for Assembly continued

AnoKiosk™

35 Congress Street, Salem, MA 01970

Tel# 1- 800 631-9707 Fax# 1-800-560-2890

e-mail:signware@rosedisplays.com

Step 4

Assemble the vertical rail assem-

blies onto the upward facing

corner brackets already inserted

into the bottom rails. All four

brackets should go into the

vertical rails at one time.

Note: (4 way only) The last

vertical rail will be tensioned.

This is normal.

Step 5

Insert corner brackets into ends

of split rails, 1 per end. Use thumb

as shown in illustration.

Step 6

Assemble split rails onto top ends

of vertical rails, one inside and

one outside of each side of the

AnoKiosk.

Step 7

Insert graphics into kiosk

with Base Rails.

Step 8

Place kiosk with stacker bar on

top of first kiosk. Line up stacker

bar with split rails on lower kiosk

and snap together.

Step 9

Load graphics into upper kiosk.

Step 10

If there are more kiosks to be

stacked repeat steps 8 and 9.

Figure 8 Figure 9

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ROSE DISPLAYS Zubehör Handbücher

ROSE DISPLAYS

ROSE DISPLAYS ANOFRAME SQUARE WITH NO LOAD WITH MULTICLIPS Bedienungsanleitung

ROSE DISPLAYS

ROSE DISPLAYS ANOKIOSK WITH ANOFOOT Bedienungsanleitung

ROSE DISPLAYS

ROSE DISPLAYS ECONOFRAME WITH SLATWALL HANGER Bedienungsanleitung

ROSE DISPLAYS

ROSE DISPLAYS ANOFRAME VERSAMOUNT WEIGHTED BASE SQ Bedienungsanleitung

ROSE DISPLAYS

ROSE DISPLAYS ECONOFRAME WITH MULTICLIP Bedienungsanleitung

ROSE DISPLAYS

ROSE DISPLAYS RAN-BAS-CC WITH CORD AND BARB Bedienungsanleitung

ROSE DISPLAYS

ROSE DISPLAYS GOTCHA WITH OLD ONEUP GOTCHA CLIPS Bedienungsanleitung

ROSE DISPLAYS

ROSE DISPLAYS SUPERSNAP WITH ANOCONNECTORS Bedienungsanleitung

ROSE DISPLAYS

ROSE DISPLAYS ROPOLE-OMNI HEAD WITH MAGNETS Bedienungsanleitung

ROSE DISPLAYS

ROSE DISPLAYS QUICKGRIP WITH WINDOW MOUNTS Bedienungsanleitung

ROSE DISPLAYS

ROSE DISPLAYS RAN-BAS-CC WITH MONOFILAMENT AND BARB Bedienungsanleitung

ROSE DISPLAYS

ROSE DISPLAYS QUICKGRIP WITH CABLE CLIP AND LOOP AND... Bedienungsanleitung

ROSE DISPLAYS

ROSE DISPLAYS RAN-BAS-CC WITH LOOP AND BALL Bedienungsanleitung

ROSE DISPLAYS

ROSE DISPLAYS ECONOSTAND WITH ANOGOTCHA Bedienungsanleitung

ROSE DISPLAYS

ROSE DISPLAYS ANOFRAME VERSAMOUNT CLAMP BASE Bedienungsanleitung

ROSE DISPLAYS

ROSE DISPLAYS ANOFRAME VERSAMOUNT SCREW BASE SQ Bedienungsanleitung

ROSE DISPLAYS

ROSE DISPLAYS ANOQUICK ROUND WITH WINDOW MOUNTS Bedienungsanleitung

ROSE DISPLAYS

ROSE DISPLAYS SUPERSNAP WITH SLATWALL HANGERS Bedienungsanleitung

ROSE DISPLAYS

ROSE DISPLAYS GOTCHA WITH GRID CLIP Bedienungsanleitung

ROSE DISPLAYS

ROSE DISPLAYS ANOQUICK ROUND WITH CABLE CLIP AND LOOP AND... Bedienungsanleitung

ROSE DISPLAYS

ROSE DISPLAYS ANOFRAME ROUND NO LOAD WITH MULTICLIPS Bedienungsanleitung

ROSE DISPLAYS

ROSE DISPLAYS ANOMULTI ROUND WITH CABLE CLIP AND LOOP AND... Bedienungsanleitung

ROSE DISPLAYS

ROSE DISPLAYS CLEVER WHATEVER Bedienungsanleitung

ROSE DISPLAYS

ROSE DISPLAYS ANOFRAME ROUND WITH MULTICLIPS Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung