Rose electronics CrystalView fiber CRK-1DFM/SUN Bedienungsanleitung

CrystalView Pro fiber ™

DVI / VGA FIBER KVM EXTENDER

INSTALLATION AND OPERATION

MANUAL

10707 Stancliff Road Phone: (281) 933-7673

Houston, Texas 77099 WWW.ROSE.COM

LIMITED WARRANTY

No part of this manual may be reproduced, stored in a retrieval system, or transcribed in any form or

any means, electronic or mechanical, including photocopying and recording, without the prior written

permission of Rose Electronics.

Rose Electronics Part # MAN-CRVPF

Printed In the United States of America – Revision 2.2

Rose Electronics warrants the CrystalView Pro Fiber to be in good working order for one year

from the date of purchase from Rose Electronics or an authorized dealer. Should this product

fail to be in good working order at any time during this one-year warranty period, Rose

Electronics will, at its option, repair or replace the Unit as set forth below. Repair parts and

replacement units will be either reconditioned or new. All replaced parts become the property of

Rose Electronics. This limited warranty does not include service to repair damage to the Unit

resulting from accident, disaster, abuse, or unauthorized modification of the Unit, including

static discharge and power surges.

Limited Warranty service may be obtained by delivering this unit during the one-year warranty

period to Rose Electronics or an authorized repair center providing a proof of purchase date. If

this Unit is delivered by mail, you agree to insure the Unit or assume the risk of loss or damage

in transit, to prepay shipping charges to the warranty service location, and to use the original

shipping container or its equivalent. You must call for a return authorization number first. Under

no circumstances will a unit be accepted without a return authorization number. Contact an

authorized repair center or Rose Electronics for further information.

ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT INCLUDING THE

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,

ARE LIMITED IN DURATION TO A PERIOD OF ONE YEAR FROM THE DATE OF

PURCHASE, AND NO WARRANTIES, WHETHER EXPRESS OR IMPLIED, WILL APPLY

AFTER THIS PERIOD. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN

IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.

IF THIS PRODUCT IS NOT IN GOOD WORKING ORDER AS WARRANTED ABOVE, YOUR

SOLE REMEDY SHALL BE REPLACEMENT OR REPAIR AS PROVIDED ABOVE. IN NO

EVENT WILL ROSE ELECTRONICS BE LIABLE TO YOU FOR ANY DAMAGES INCLUDING

ANY LOST PROFITS, LOST SAVINGS OR OTHER INCIDENTAL OR CONSEQUENTIAL

DAMAGES ARISING OUT OF THE USE OF OR THE INABILITY TO USE SUCH PRODUCT,

EVEN IF ROSE ELECTRONICS OR AN AUTHORIZED DEALER HAS BEEN ADVISED OF

THE POSSIBILITY OF SUCH DAMAGES, OR FOR ANY CLAIM BY ANY OTHER PARTY.

SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR

CONSEQUENTIAL DAMAGES FOR CONSUMER PRODUCTS, SO THE ABOVE MAY NOT

APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY

ALSO HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is likely

to cause harmful interference in which case the user will be required to correct the interference

at his own expense.

IBM, AT, and PS/2 are trademarks of International Business Machines Corp. Microsoft and

Microsoft Windows are registered trademarks of Microsoft Corp. Any other trademarks

mentioned in this manual are acknowledged to be the property of the trademark owner.

FCC/IC STATEMENTS, EU DECLARATION OF CONFORMITY

FEDERAL COMMUNICATIONS COMMISSION

AND INDUSTRY CANADA

RADIO-FREQUENCY INTERFERENCE STATEMENTS

This equipment generates, uses and can radiate radio frequency

energy and if not installed and used properly, that is in strict

accordance with the manufacturer’s instructions may cause

interference to radio communication. It has been tested and found to

comply with the limits for a Class A digital device in accordance with

the specifications of Part 15 of FCC rules, which are designed to

provide reasonable protection against such interference when the

equipment is operated in a commercial environment. Operation of this

equipment in a residential area is likely to cause interference, in which

case the user at his own expense will be required to take whatever

measures may be necessary to correct the interference.

Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to operate

the equipment.

This digital apparatus does not exceed the Class A limits for radio

noise emission from digital apparatus set out in the Radio Interference

Regulation of Industry Canada.

Le présent appareil numérique n’émet pas de bruits radioélectriques

dépassant les limites applicables aux appareils numériques de la

classe A prescrites dans le Règlement sur le brouillage radioélectrique

publié par Industrie Canada.

EUROPEAN UNION DECLARATION OF CONFORMITY

CE DECLARATION OF CONFORMITY

This equipment is in conformity with the

Council Directives 89/336/EEC

The Declaration of Conformity is based upon

compliance of the product with the following

standards:

EN55022: 1999 Class A

EN55024: 1999

IEC61000-4-2: 2001

IEC61000-4-3: 2001

IEC61000-4.4: 2001

EN61000-3-2 2001

EN61000-3-3 2002

This equipment has been found to comply with the limits for a Class A

digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with the instruction manual,

may cause harmful interference to radio communications. Operation of

this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the

interference at his own expense.

TABLE of CONTENTS

Contents Page #

Disclaimer...............................................................................................1

System Introduction................................................................................1

Features..............................................................................................2

Compatibility...........................................................................................2

DVI or VGA.............................................................................................3

PC Model................................................................................................4

SUN Model.............................................................................................5

USB Model .............................................................................................6

Rack Model.............................................................................................6

Optical Elements ....................................................................................7

Cables ....................................................................................................7

Device Control -OSD..............................................................................8

OSD Menu descriptions .........................................................................9

Menu descriptions...............................................................................9

Installation ............................................................................................15

Transmitter to Receiver cabling........................................................16

SET-UP instructions (Mixed DVI and VGA)......................................17

Additional keyboard commands........................................................19

Applying power .................................................................................19

Operating instructions ..........................................................................20

Private Mode ........................................................................................20

Frame Rates.........................................................................................20

Troubleshooting....................................................................................21

Service Information ..............................................................................22

Maintenance and Repair...................................................................22

Technical Support.............................................................................22

Safety ...................................................................................................23

Tables Page #

Table 1. Timeout / switching method .....................................................3

Table 2. Transmitter to receiver cabling...............................................16

Table 3. Pixel clock /phase examples..................................................18

Figures Page #

Figure 1. PC Model ................................................................................4

Figure 2. SUN Model..............................................................................5

Figure 3. USB Model..............................................................................6

Figure 4. Input Select Menu...................................................................9

Figure 5. Scale mode menu...................................................................9

Figure 6. Brightness/Contrast menu ....................................................10

Figure 7. Color / Color temp menu.......................................................11

Figure 8. Image menu..........................................................................12

Figure 9. Tools menu ...........................................................................13

Figure 10. Save menu..........................................................................14

Figure 11. Typical cabling configurations.............................................15

INTRODUCTION

CRYSTALVIEW PRO FIBER

INSTALLATION AND OPERATIONS MANUAL 1

Disclaimer

While every precaution has been taken in the preparation of this manual,

the manufacturer assumes no responsibility for errors or omissions.

Neither does the manufacturer assume any liability for damages resulting

from the use of the information contained herein. The manufacturer

reserves the right to change the specifications, functions, or circuitry of the

product without notice.

The manufacturer cannot accept liability for damages due to misuse of the

product or other circumstances outside the manufacturer’s control. The

manufacturer will not be responsible for any loss, damage, or injury arising

directly or indirectly from the use of this product.

System Introduction

Thank you for choosing the Rose ElectronicsCrystalView Pro Fiber

KVM station extender. The CrystalView Pro Fiber is a very versatile KVM

extender. It supports the latest digital DVI as well as analog VGA. All

combinations of DVI and VGA monitors and video cards are supported.

With this flexibility, you can connect a VGA video card to a DVI monitor, or

a DVI video card to a VGA monitor.

The modular architecture design of the CrystalView Pro Fiber provides the

flexibility to support PS/2 and SUN connections and different cable types

such as Multimode fiber and Singlemode fiber. A serial port can be added

to support Touch-Screen. Stereo audio, USB, parallel port and other

custom interfaces can also be added.

The system consists of two Units, a transmitter and a receiver. The

transmitter connects to your CPU or a Rose switch and the receiver

connects to a keyboard, video monitor and mouse or KVM station. The

transmitter and receiver are connected together with industry standard

multimode or singlemode fiber optic cable. The receiver can be up to

33,000 feet from the transmitter using singlemode fiber cable

The CrystalView Pro Fiber is available in several models, the PC model,

the Sun model and a USB model. The PC model is available with

transmitter and receiver KVM access. The transmitter KVM version allows

an additional KVM station to be connected to the transmitter unit.

2 CRYSTALVIEW PRO FIBER

INSTALLATION AND OPERATIONS MANUAL

Using the CrystalView Pro Fiber to remotely access your computer has

several advantages over conventional CAT-5 cable. Using fiber cable, you

can extend the distance between the transmitter and receiver up to 33,000

feet. In addition, fiber cable is unaffected by electromagnetic interference,

keeping your data safe from interference by lightning and over voltage

transients. Computers used in hazardous industrial environments can be

accessed remotely, keeping the users safe and unexposed to any hazards.

Features

JPerfect image quality at resolutions up to 1600 x 1200 @ 60Hz

(The 2.5GBit option allows a resolution up to 1920 x 1200 @ 60Hz)

JExtend a KVM station from a computer up to:

J650 feet (200m) over 62.5/125µm Multimode fiber

J1,310 feet (400m) over 50/125 µm Multimode fiber

J33,000 feet (10km) over 9/125µm Singlemode fiber

J300 feet (100m) over CAT5, 5e, 6 cable

JAll models feature dual access allowing both transmitter and receiver

operation (Local DVI access limited to 1280 x 1024 resolution)

JSupports all combinations of DVI or VGA video cards and monitors

JSupports all operating systems and is flash upgradeable

JOn-screen display for adjusting brightness, contrast, saturation, pixel

clock, and other video parameters and controls

JFully automatic KVM sharing on a first-come, first-serve basis

JPrivate mode for inhibiting the transmitter or receiver KVM station

JKeyboard and mouse emulation ensures the computer does not lock-up

and allows peripherals to be connected without removing power

JCompatible with Rose Electronics family of KVM switches

JDiagnostic LEDs showing communication error, link, device ready, and

video signal status

JOptional serial port provides extended support up to 19.2K Baud.

JBi-directional full stereo audio option at digital CD quality (16 bit)

JRack mount kits available in 19”, 23”, and 24” sizes

Compatibility

Computers PCs, SUN, UNIX, Linux (All operating systems)

Video – Analog

Video – Digital VGA – UXGA (separate, composite, sync-on-green)

DVI single link

Keyboard PS/2, Sun, USB

Mouse PS/2, 2 or 3 button, wheel mice

Serial 19.2K Baud (Extends TX, RX, RTS, CTS, DTR, DSR)

Audio Line-level In/Out, Amplified speakers required

CRYSTALVIEW PRO FIBER

INSTALLATION AND OPERATIONS MANUAL 3

DVI or VGA

The CrystalView Pro Fiber is designed to work with any combination of

VGA and DVI video cards and monitors. The ideal configuration is using a

DVI video card, a TFT monitor and DVI video cables. With this

configuration, no adjustments are needed. A set-up procedure may be

needed if you are using a VGA video card and a TFT, DVI monitor or a

DVI video card and a VGA monitor. The installation section of this

manual describes these procedures for different combinations of

equipment and cables.

Access Switching (PS/2 only - Transmitter or receiver)

Access to the computer from the receiver or the transmitter is on a first

come, first serve basis. When a key is pressed on one of the keyboards,

this KVM station becomes the active station. The other KVM station is

inhibited until there is a pre-defined amount of non-activity from the

controlling KVM station. This pre-defined amount of non-activity time can

be changed from the 2 second default setting to 15 seconds by changing

the jumper settings. Switching can also be done by pressing both the

‘Left’ and ‘Right’ mouse buttons simultaneously.

Table 1 shows the jumper settings for changing the inactivity timeout and

the method of switching control to the transmitter or receiver. The default

setting is after 2 seconds on inactivity on the controlling KVM station the

other KVM station can gain control. The default method of switching

control to a KVM station is pressing any key on the keyboard or pressing

the left and right mouse buttons simultaneously. The top jumper (J2) sets

the inactivity timeout and the bottom jumper (J3) sets the switching

method (Keyboard only or Keyboard and mouse).

To change these values, carefully remove the cover on the RECEIVER

UNIT (8 screws) and locate the J2/J3 jumper block and install a jumper as

shown in Table 1 to set the timeout and switching method.

Inactivity timeout (J2) 2 2 15 15

(2 sec / 15 sec)

Switching method (J3)

K=keyboard

M=Mouse

K & M

(Default) K K & M K

Table 1. Timeout / switching method

MODELS

4 CRYSTALVIEW PRO FIBER

INSTALLATION AND OPERATIONS MANUAL

PC Model

Receiver

Transmitter

Figure 1. PC Model

Connectors:

Receiver unit

JRJ11 – Programming (See Appendix C)

JDVI-I – DVI / VGA Video monitor

J(2) MiniDin-6 – PS/2 Keyboard / mouse

JSC-Type – Fiber

J4-pin square – Power

JDB9M – Serial data input

J(2) 3.5mm Stereo audio jacks

Transmitter unit

J4-pin square – Power

JDVI-I – DVI/VGA – CPU video connection.

JDVI-I – DVI/VGA – KVM stations video monitor connection.

J(4) MiniDin-6 – (2) CPU keyboard and mouse connections /

(2) KVM keyboard and mouse connections.

JFiber – SC-type

JRJ11 – Programming (See Appendix C)

JDB9F – Serial data input (Optional)

J(2) 3.5mm stereo audio input/output (Optional)

Andere Handbücher für CrystalView fiber CRK-1DFM/SUN

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Rose electronics Extender Handbücher

Rose electronics

Rose electronics CrystalView Plus Bedienungsanleitung

Rose electronics

Rose electronics CrystalView DVI Mini Bedienungsanleitung

Rose electronics

Rose electronics CrystalLink USB Fiber Bedienungsanleitung

Rose electronics

Rose electronics CrystalView Mini Bedienungsanleitung

Rose electronics

Rose electronics CrystalView fiber CRK-1DFM/SUN Bedienungsanleitung

Rose electronics

Rose electronics CrystalView DVI Plus Bedienungsanleitung

Rose electronics

Rose electronics Xcion DVI/VGA over CATx Bedienungsanleitung

Rose electronics

Rose electronics CrystalLink USB2.0 CATx Bedienungsanleitung

Rose electronics

Rose electronics CrystalView Extreme Bedienungsanleitung

Rose electronics

Rose electronics CRK-1DFMPDVI/SF Bedienungsanleitung

Rose electronics

Rose electronics ViewLink Coax Bedienungsanleitung

Rose electronics

Rose electronics AUTO EQUALIZATION Bedienungsanleitung

Rose electronics

Rose electronics CrystalLink USB3.1 Fiber Dual Port Bedienungsanleitung

Rose electronics

Rose electronics CrystalView DVI EX Bedienungsanleitung

Rose electronics

Rose electronics CrystalView Plus Bedienungsanleitung

Rose electronics

Rose electronics CrystalView DVI CAT Series Bedienungsanleitung

Rose electronics

Rose electronics Crystal View Bedienungsanleitung

Rose electronics

Rose electronics CrystalLink USB2.0 CATx Bedienungsanleitung

Rose electronics

Rose electronics CrystalLink USB2.0 CATx Bedienungsanleitung

Rose electronics

Rose electronics CrystalLink USB3.1 Fiber Dual Port Bedienungsanleitung

Rose electronics

Rose electronics CRYSTALVIEW USB 1.1 Bedienungsanleitung

Rose electronics

Rose electronics CrystalLink USB-3-2-1 Fiber Bedienungsanleitung

Rose electronics

Rose electronics CrystalLink CLK-1U4TP-100M/PE Bedienungsanleitung

Rose electronics

Rose electronics CrystalLink USB-3-2-1 Fiber Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung