Ruijie RG-RSR77 Series Bedienungsanleitung

RG-RSR77 Series Router

Installation and Initialization

Contents

■Device Installation

■Initialization Configuration

Preface

Revision History

Audience

Ruijie business partners and customers who are responsible for configuring

and maintaining Ruijie wireless devices.

Date

Change Contents

Reviser

2016.3

Initial

publication V1.0

TAC

Oversea

Note :

For more detail configuration , see configuration guide for each product . you can download

configuration guide at http://www.ruijienetworks.com

For more technical enquiry , you can visit Ruijie Service portal at

http://case.ruijienetworks.com . You need to sign up before submit a case.

Hardware Installation

Preparations Installing the

Chassis to a

Specified

Position

Grounding

and

Connecting

Cables

Installing the

Supervisor

and Cards Power-on

Check

Safety Notes

①Do not install the devices in a wet place and keep them away from liquid.

②Keep routers away from heat sources.

③Check that routers are properly grounded. Do not remove cables when the power is not interrupted.

④Wear an ESD wrist strap during installation and maintenance.

⑤Do not wear loose clothes during installation to avoid hooking components and causing damage.

Therefore, fasten clothes ribbons, scarves, and sleeves.

⑥Place tools and components away from passageways to prevent collision.

⑦It is recommended that UPSs be used to prevent power interruption and power interference.

Ambient Requirements

①Temperature: 0℃ to 45℃

②Relative humidity: 10% to 90%

③Anti-interference: far away from high-power, high-frequency, or large-current devices

Hardware Installation

Steps of Installing the Chassis in a Cabinet

①Before installing the chassis in a cabinet, check that the cabinet space is sufficient, and read the RG-

RSR77 Series Router Hardware Installation and Reference Guide to get familiar with relevant

installation notes and device size information.

②The device should be installed in a cabinet straightly and smoothly. If you feel obstruction, check

whether the cabinet or device slots are damaged or deformed. Do not install the device with brute

force.

③The RG-RSR77 series routers are very heavy and they should be installed at the bottom of cabinets.

④It is recommended that you install an empty chassis in the cabinet first and then install line cards.

⑤When installing a device in a cabinet, all side screws of the device rather than screws only in the

diagonal lines or only some side screws should be tightened.

⑥It is recommended that a bracket be used to reinforce each device based on the cabinet layout.

⑦To ensure proper running of the heat dissipation system of the device, certain space (5-10 cm) must

be reserved between the device and the cabinet sides and 1U space should be reserved between

devices. For enclosed-type cabinets (with windproof glass cabinet doors), space should be reserved

between the device and cabinet front and rear panels. Otherwise, it is recommended that the cabinet

front and rear panels be dismantled.

⑧The RSR77 uses the side heat dissipation mode in which air flows in from the left side and flows out

from the right side. Do not block the side ventilation holes because of cabling during installation.

Otherwise, hot air circulates in and out of the device.

Preparations Installing the

Chassis to a

Specified

Position

Grounding

and

Connecting

Cables

Installing the

Supervisor

and Cards Power-on

Check

Hardware Installation

There Is a Ground Bar in the Installation

Environment (Recommended)

①Remove the ground screw from the rear panel of

the device.

②Put the OT terminal of the ground cable delivered

with the device on the ground screw of the chassis.

③Install the ground screw with the OT terminal to the

ground hole, fasten it with a screwdriver, and

connect the other end of the ground cable to the

ground bar of the equipment room.

There Is No Ground Bar in the Installation

Environment

When there is no ground bar in the environment where

the device is to be installed and the device adopts AC

power supply, the PE cable of the AC power supply

needs to be grounded. Check whether the PE cable of

the AC power supply is properly grounded in the power

distribution room or on the AC transformer side.

Rear panel of the device

Grounding label

Grounding hole

OT terminal of the

protective ground cable

Protective ground cable

Ground screw

Preparations Installing the

Chassis to a

Specified

Position

Grounding

and

Connecting

Cables

Installing the

Supervisor

and Cards Power-on

Check

Hardware Installation

Connection Cable Requirements

①AC power: 100-240 V~/50-60 Hz

②The power cable is a 3-wire cable. It is recommended that the single-phase three-wire socket

with neutral-point connector or multi-functional microcomputer power socket be used.

Installing the Power Cable

①After confirming that the power switch of the router is turned to the OFF position, insert one

end of the power cable delivered with the router into the power module socket on the rear

panel of the router chassis, and then insert the other end into the AC power socket.

②Turn the power switch of the router to the ON position.

③Check whether the power indicator on the front panel of the router is on. If it is on, the power

connection is correct.

Preparations Installing the

Chassis to a

Specified

Position

Grounding

and

Connecting

Cables

Installing the

Supervisor

and Cards Power-on

Check

Hardware Installation

Installing the Supervisor

①Operators should face the front panel of the router.

②Align the router supervisor with the opening edge of the supervisor slot on the front panel of

the router.

③Push the router supervisor into the router, raise the self-locking levers on the panel of the

router supervisor and push them inwards till the router supervisor is in close contact with the

front panel of the router.

④Tighten the fastening screws on the router supervisor.

Notes

①Though the device support hot swap, it is recommended that the device be powered on after

cards are installed completely.

②Before installing the router supervisor, check that the ID of the slot for accommodating the

router supervisor is M1 or M2. Do not insert the router supervisor into a line card slot.

Otherwise, the control module will be damaged.

Preparations Installing the

Chassis to a

Specified

Position

Grounding

and

Connecting

Cables

Installing the

Supervisor

and Cards Power-on

Check

Hardware Installation

Installing Cards

①Operators should face the front panel of the router.

②Align a router card with the opening edge of the service slot on the front

panel of the router.

③Push the card into the router, raise the self-locking levers on the panel of

the router card, and push them inwards till the card is in close contact with

the front panel of the router.

④Tighten fastening screws on the card.

Preparations Installing the

Chassis to a

Specified

Position

Grounding

and

Connecting

Cables

Installing the

Supervisor

and Cards Power-on

Check

Hardware Installation

Card Installation Notes

①Before installing a router card, check the ID of the slot for accommodating the card. Do

not insert it into the M1 or M2 slot. Otherwise, the card will be damaged.

②Insert router cards with light force smoothly. If you find it is difficult to push a card

inwards, do not push it with brute force. Remove the card, check whether the card is

aligned with the opening edge of the service slot on the front panel of the router, and

then proceed with operations. Otherwise, the card may be damaged.

③The SIP2 card has only one self-locking lever. Use the self-locking lever and the

fastening screw during installation, to prevent uneven force and card damage. Raise

the self-locking lever on the panel of the SIP2 card and push it inwards, and hold the

fastening screw on the card and push it inwards till the card is in close contact with the

front panel of the router. Then, tighten the fastening screws on the card.

Preparations Installing the

Chassis to a

Specified

Position

Grounding

and

Connecting

Cables

Installing the

Supervisor

and Cards Power-on

Check

Andere Handbücher für RG-RSR77 Series

Inhaltsverzeichnis

Andere Ruijie Netzwerk-Router Handbücher

Ruijie

Ruijie Reyee RG-EG210G-E Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-EW Series Bedienungsanleitung

Ruijie

Ruijie RG-MTFi-M520 Bedienungsanleitung

Ruijie

Ruijie Reyee RG-EW Series Anleitung zur Verwendung

Ruijie

Ruijie RG-RSR77 Series Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-EG V2 Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-RSR30-XA Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-EG210G-E Series Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-EG209GS Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-EW1300G Bedienungsanleitung

Ruijie

Ruijie RSR10-01G Montageanleitung

Ruijie

Ruijie Reyee RG-EW1200 Bedienungsanleitung

Ruijie

Ruijie Reyee RG-EW Series Bedienungsanleitung

Ruijie

Ruijie Reyee RG-EW3200GX PRO Bedienungsanleitung

Ruijie

Ruijie Reyee RG-NBR-E Series Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-EW3200GX PRO Bedienungsanleitung

Ruijie

Ruijie RG-RSR77 Series Betriebsanleitung

Ruijie

Ruijie RG-RSR77-XA Series Installations- und Betriebsanleitung

Ruijie

Ruijie RSR30-X-SPU10 Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-EG105GW-X Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-EG300GH-E Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-RSR10-02E Series Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-EG105GWT Installations- und Betriebsanleitung

Ruijie

Ruijie RG-R SR30 Series Installations- und Betriebsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung