Ruijie RSR30-X-SPU10 Installations- und Betriebsanleitung

RSR30-X Series Router

Hardware Installation and Reference Guide

Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup,

modification, transmission, translation or commercial use of this document or any portion of this document,

in any form or by any means, without the prior written consent of Ruijie Networks is prohibited.

Exemption statement

This document is provided “as is”. The contents of this document are subject to change without any notice.

Please obtain the latest information through the Ruijie Networks website. Ruijie Networks endeavors to

ensure content accuracy and will not shoulder any responsibility for losses and damages caused due to

content omissions, inaccuracies or errors.

Preface

Thank you for using our products. This manual will guide you through the installation of the router.

Scope

It is intended for the users who have some experience in installing and maintaining network hardware. At the same time, it

is assumed that the users are already familiar with the related terms and concepts.

Obtaining Technical Assistance

Ruijie Networks Website: https://www.ruijienetworks.com/

Technical Support Website: https://ruijienetworks.com/support

Case Portal: http://caseportal.ruijienetworks.com

Community: http://community.ruijienetworks.com

Technical Support Email: servi[email protected]

Skype: [email protected]

Related Documents

Documents

Description

Configuration Guide

Describes network protocols and related mechanisms that supported by the

product, with configuration examples.

Command Reference

Describes the related configuration commands, including command modes,

parameter descriptions, usage guides, and related examples.

Documentation Conventions

The symbols used in this document are described as below:

This symbol brings your attention to some helpful suggestions and references.

This symbol means that you must be extremely careful not to do some things that may damage the device or cause

data loss.

1 Product Overview

Ruijie RSR30-X series router is a data communication product independently developed by Ruijie Networks Co. Ltd. by

using advanced semiconductor technologies and communication control technologies. Ruijie RSR30-X series router is

developed in full compliance with international standards; therefore, it is similar to major routers in terms of use and

configuration approach. Network administrators who are familiar with the configuration commands of major routers may

use the routers without receiving training first.

1.1 Ruijie RSR30-X Router

1.1.1 Product Introduction

Ruijie RSR30-X router provides a high processing capability. The RSR30-X supports power supply redundancy backup

and offers abundant optional modules for users. It can be used as the core router on medium or small enterprise

networks or aggregation router on large industry networks.

Using high performance microprocessor and Ruijie’s proprietary network operating system, the RSR30-X supports BGP,

IP multicast, high speed forwarding and rich QoS features to offer comprehensive network solutions for the industries

such as telecommunications, private network, ISP, finance, tax, public security, and railways as well as middle and

large-sized enterprises.

The RSR30-X has the following features:

Reliability: advanced hardware architecture, efficient packet forwarding mechanism, good compatibility and

scalability, and high reliability of software and hardware.

Multiple services: Integrated features such as switching, QoS, VPN, security, and IPv6.

High-performance software and hardware.

Refined full-service QoS: refined service management, and support of packet classification flags, congestion

mitigation (RED and WRED), traffic supervision (CAR), traffic shaping (GTS), congestion management (FIFO, PQ,

CQ, WFQ, CBWFQ, LLQ, and RTPQ), link efficiency (CTCP and CRTP), and high-accuracy QoS queue

scheduling technology.

Efficient and convenient REF forwarding technology.

Unique virtual CPU technology VCPU.

Built-in distributed firewall with high security.

High-density access for flexible user connections.

Abundant service features, such as STP, 802.1X authentication, and port rate limit. In this sense, the router can be

used as a high-performance switch.

Dual-power supply that supports hot swapping.

Software delivery in batches.

Rich routing protocol features.

Support of IGP routing protocols, including RIPv1/v2, OSPFv2/v3, ISIS, and BGP.

Support of IPv6 tunnel technologies, including the SATAP runnel, IPv6 manually-configured tunnel,

IPv4-compatible automatic tunnel, IPv6 to IPv4 tunnel, IPv6 over IPv4 GRE tunnel, and IPv6 over IPv4 tunnel.

IPv6 over IPv4 tunnel technologies, including IPv6 manually-configured tunnel and IPv4-compatible automatic

tunnel.

Support of multicast routing protocols, including IGMPv1, IGMPv2, IGMPv3, DVMRP, and PIM DM/SM.

1.1.2 RSR30-X-SPU10 V1.5

The RSR30-X-SPU10 V1.5 is an integrated host.

Specifications

Product Model

RSR30-X-SPU10 V1.5

Service Module Slot

A maximum of two HNM modules can be configured on

the front panel of the RSR30-X-SPU10 V1.5.

A maximum of two HSIC modules can be configured on

the rear panel of the RSR30-X-SPU10 V1.5.

Power Supply Slot

A maximum of two power supplies can be configured for

the RSR30-X-SPU10 V1.5.

Hot Swapping

Support (both service modules and power supplies support hot swapping).

Power Redundancy

Support.

Memory

DDR: 2 GB

FLASH: 512 MB

I/O Interface

Ethernet interface:

Nine GE ports (GE: 0/0/0-0/0/8) that support auto-negotiation.

Eight SFP ports that support the 1000BASE-SX/LX/LH/ZX SFP and 100BASE-FX

SFP modules.

Eight GE combo ports (GE: 0/0/1-0/0/8).

One RJ45 console port

One mini USB console port

One USB port.

One SD slot.

One FUNC button for one-click reset or upgrade.

Indicator

One indicator provided for GE 0/0/0.

Eight indicators (1, 2, 3, 4, 5, 6, 7, and 8) for GE 0/0/1 to GE 0/0/8.

Eight indicators (1F, 2F, 3F, 4F, 5F, 6F, 7F, and 8F) for SFP 0/0/1 to SFP 0/0/8.

One indicator for the USB port.

Six system indicators (SD, Slot0/3, Slot0/4, PWR0, PWR1, and SYS).

Voltage

100VAC-240VAC, 50/60 Hz

Power Supply

RG-M5000E-AC60: 100VAC to 240VAC, 50/60Hz, maximum power of 60W.

RG-PD240I DC power: -75V to -40V, maximum power of 60W.

System Power Consumption

< 60W

Operating Temperature

0°C to 50°C (32°F to 122°F)

Operating Humidity

10% to 90% RH (non-condensing)

Dimensions (W x H x D) (mm)

440mm x 44mm x 435mm

Product Images

Figure 1-1 Front Panel

Figure 1-2 Back Panel

Indicators and Buttons

Mark

Note

Description

SYS

System status indicator of

the local control board

Off: The system is not powered on or the system is

abnormal.

Solid red: The system is abnormal.

Blinking green: The system is initializing.

Solid green: The system has completed initialization and

is operational.

PWR0 and PWR1

Power status indicator

(corresponding to power

module slots 0 and 1)

Off: The power module is not installed.

Solid red: The module is abnormal or is not powered on.

Solid green: The module is operational.

Slot 0/3

Slot 0/4

HSIC slot status indicator

Off: The module is not powered on or is not properly

inserted, or the module can be unplugged.

Blinking green: The module is initializing.

Solid green: Initialization is complete, and the module is

operational.

SD card status indicator

Off: The SD card is not installed, is not properly inserted,

or can be unplugged.

Solid red: The device is abnormal.

Blinking green: The system is accessing the SD card.

Solid green: The device is operational.

1000M

GE0 port rate indicator

Off: 10 M or 100 M.

Solid orange: 1000 M link up.

Link/Act

GE0 port status indicator

Off: The port is not connected.

Solid green: The port is connected at 10/100/1000 Mbps.

Blinking green: The port is transmitting or receiving data

at 10/100/1000 Mbps.

RJ45

1-8

Status indicator for RJ45

ports 1 to 8

Off: The port is not connected.

Solid green: The port is connected at 1000 Mbps.

Blinking green: The port is transmitting or receiving data

Mark

Note

Description

at 1000 Mbps.

Solid yellow: The port is connected at 10/100 Mbps.

Blinking yellow: The port is transmitting or receiving data

at 10/100 Mbps.

SFP

1-8F

Status indicator for

optical ports 1F to 8F

Off: The port is not connected.

Solid green: The port is connected at 1000 Mbps.

Blinking green: The port is transmitting or receiving data

at 1000 Mbps.

Solid yellow: The port is connected at 100 Mbps.

Blinking yellow: The port is transmitting or receiving data

at 100 Mbps.

USB

USB status indicator

Off: The USB device is not installed, is not properly

inserted, or can be unplugged.

Blinking green: The system is accessing the USB device.

Solid green: The device is operational.

FUNC

One-click reset/upgrade

button

See the description of the FUNC button in the following

section.

U-Console

U-Console port

Connected to the console through a USB cable.

Note: The Console and U-Console share the same port and either is available at a time. The port for mini USB is

the mini USB-B connector and only the 5-pin mini-B connector or compatible connector cable can be used.

To use the U-Console port, install the dedicated driver on the console. For details, see the RGOS Configuration

Guide.

USB Port

RSR30-X-SPU10 provides one USB port. This port allows routers to read configurations from the USB device or save

configurations to the USB device. Ruijie RGOS operating system can be stored in the USB device. You can press the

FUNC button to upgrade the operating system.

Features

Settings

Interface standard

USB 2.0

Connection component

USB Host

Interface mode

Host

Hot swapping

Support

Hot swapping of the USB device must be operated according to the "Reliability Configuration" section in the

RGOS Configuration Guide. Hot swapping is not allowed before you run the USB remove command.

The USB device here mainly refers to a USB flash disk.

SD Slot

RSR30-X-SPU10 provides one SD slot. Ruijie RGOS operating system can be stored on the SD card. You can press

the FUNC button to upgrade the operating system.

Features

Settings

Interface Standard

SD/SDHC

Connection Component

SD Connector

Rate

1.5 MB/sec

Interface Mode

Device

SD Cards

Ruijie SD cards are supported.

Hot Swapping

Support

Hot swapping of the SD card must be operated according to the "Reliability Configuration" section in the RGOS

Configuration Guide. The system on the SD card may be faulty if you perform hot swapping before inputting the

SD card pullout command. Only Ruijie SD cards are supported.

FUNC Button

The FUNC button is used on the RSR30-X routers.

One-Click System Reset

If you press the FUNC button when no SD card or USB flash disk is inserted, the system resets and restarts in the

original software version.

One-Click Software Upgrade

If you press the FUNC button when an SD card or USB flash disk is inserted, the system scans installation packages

that are applicable to the current device in the root directory of the SD card or USB flash disk in sequence. The system

is upgraded immediately after the first available installation package is found. After the upgrade is complete, the system

resets and restarts in the new software version.

The system scans SD cards in prior to USB flash disks. The system scans USB flash disks only when no SD card

is inserted or no installation package is available on the SD cards. If no installation package is available on the

inserted SD card and USB flash disk, the system resets and but does not upgrade the software. The system still

restarts in the original software version.

The installation package file name is in the format of PProduct nameV1_Version number_RRelease

number_install.bin.

The system scans installation packages only in the root directories of the SD card or USB flash disk and the SD

card always has the priority.

It is recommended to save only one installation package in the root directory of the SD card or USB flash disk. If

there are multiple installation packages in the root directory, the system selects an installation package at random.

Therefore, the searching sequence of software versions cannot be ensured.

Procedure

Save the bin file of the installation package for the new software version in the root directory of the SD card or USB

flash disk and insert the SD card or USB flash disk into the device.

The installation package file name is in the format of Product name_Version number_RRelease number_install.bin.

For example, RSR30-X_10.4(3b76)_R199863_install.bin.

Press the FUNC button. The system performs software upgrade and resets.

After system restart, run the show version command to check whether the software version has been updated.

If you need to reset the system only, ensure that there is no installation package on the SD card or USB flash disk.

Alternatively, simply press the FUNC button without inserting any SD card or USB flash disk. For detailed

operations, see the RGOS Configuration Guide of the RSR30-X router.

1.2 Service Modules

Service modules are not supported.

1.3 Power Supply Modules

There are two available power supply modules: M5000E-AC60 and PD240I.

1.3.1 M5000E-AC60

Product Image

Figure 1-3 Appearance of Two M5000E-AC60 Power Supply Modules

Indicators

Indicator

Description

Indicator on the panel

Green: Power output is normal.

Red: Power output is abnormal.

Off: There is NO power output due to faulty power supply module or no inserted cable.

Specifications

Table 1-4 Technical Specifications of the M5000E-AC60 Module

Module Model

RG-M5000E-AC60

Rated Voltage Range

100VAC-240VAC, 50-60Hz

Max Voltage Range

90VAC~264VAC, 50-60Hz

Power

60W

Hot Swapping

Supported

Power Redundancy

Supporting 1+1 power redundancy

Overvoltage

Protection

13.4VAC-16VAC

Overcurrent Protection

6A-12A

Power Supply Mix

Not supported

Power Cord

Requirement

10A power cord

Dimensions (W x H x

D) (mm)

203.3mm x 81mm x 40mm (Excluding the connecting finger and the handle.)

236.9mm x 81mm x 40mm (Including the connecting finger and the handle.)

Weight

0.6kg

1.3.2 PD240I

Product Image

Figure 1-5 Appearance of Two RG-PD240I Power Supply Modules

Indicators

Indicator

Description

Indicator on the panel

Green: Power output is normal.

Red: Power output is abnormal.

Off: There is NO power output due to faulty power supply module or no inserted cable.

Specifications

Table 1-1 Technical Specifications of the M5000E-AC60 Module

Module Model

RG-PD240I

Rated Voltage Range

-36VDC- -72VDC

Power

60W

Hot Swapping

Supported

Power Redundancy

Supporting 1+1 power redundancy

Overvoltage

Protection

18VDC

Overcurrent Protection

5.5A-10A

Power Supply Mix

Not supported

Power Cord

Requirement

Power cord supplied with the RG-PD240I router

Dimensions (W x H x

D) (mm)

203.3mm x 81mm x 40mm (Excluding the connecting finger and the handle.)

236.9mm x 81mm x 40mm (Including the connecting finger and the handle.)

Weight

0.6kg

N+1 power redundancy: In terms of a system requiring N power supply modules, if a module fails, the backup

module starts to operate immediately. In this way, system reliability is guaranteed.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ruijie Netzwerk-Router Handbücher

Ruijie

Ruijie RG-RSR77 Series Betriebsanleitung

Ruijie

Ruijie RG-RSR20-14E Series Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-EG105GWT Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-EG300GH-E Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-RSR77-XA Series Installations- und Betriebsanleitung

Ruijie

Ruijie RSR10 Series Montageanleitung

Ruijie

Ruijie Reyee RG-EW Series Anleitung zur Verwendung

Ruijie

Ruijie RG-RSR30-XA Series Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-EG210G-E Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-EW1300G Bedienungsanleitung

Ruijie

Ruijie RG-RSR77 Series Installations- und Betriebsanleitung

Ruijie

Ruijie RSR10-01G-T-I Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-S6200 Series Bedienungsanleitung

Ruijie

Ruijie Reyee RG-EG V2 Series Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-EG Series Bedienungsanleitung

Ruijie

Ruijie Reyee RG-EW Series Abmessungen

Ruijie

Ruijie Reyee RG-EW1200 Bedienungsanleitung

Ruijie

Ruijie RSR10-01G Montageanleitung

Ruijie

Ruijie Reyee RG-M18 Bedienungsanleitung

Ruijie

Ruijie RG-RSR77 Series Bedienungsanleitung

Ruijie

Ruijie Reyee RG-EW Series Bedienungsanleitung

Ruijie

Ruijie Reyee RG-EW3000GX PRO Bedienungsanleitung

Ruijie

Ruijie Reyee RG-EW3200GX PRO Bedienungsanleitung

Ruijie

Ruijie Reyee RG-EW3000GX PRO Installations- und Betriebsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung