Ruijie RG-S8600E Series Bedienerhandbuch
RG-S8600E Series Switches
Quick Installation Guide V1.02
Copyright Statement
Ruijie Networks©2017
Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup, modification, transmission, translation
or commercial use of this document or any portion of this document, in any form or by any means, without the prior written consent of
Ruijie Networks is prohibited.
Exemption Statement
This document is provided “as is”. The contents of this document are subject to change without any notice. Please obtain the latest
information through the Ruijie Networks website. Ruijie Networks endeavors to ensure content accuracy and will not shoulder any
responsibility for losses and damages caused due to content omissions, inaccuracies or errors.
Preface
Thank you for using our products. This manual will guide you through the installation of the device.
This manual describes the functional and physical features and provides the device installation steps, hardware
troubleshooting, module technical specifications, and specifications and usage guidelines for cables and connectors.
Audience
It is intended for the users who have some experience in installing and maintaining network hardware. At the same time, it
is assumed that the users are already familiar with the related terms and concepts.
Obtaining Technical Assistance
Ruijie Networks Website: http://www.ruijienetworks.com/
Service Email: [email protected]
Technical Support: http://www.ruijienetworks.com/service.aspx
Technical Support Hotline: +86-4008-111-000
Related Documents
Documents
Description
Configuration Guide
Describes network protocols and related mechanisms that supported by the
product, with configuration examples.
Command Reference
Describes the related configuration commands, including command modes,
parameter descriptions, usage guides, and related examples.
Symbol Conventions
Means reader take note. Notes contain helpful suggestions or references.
Means reader be careful. In this situation, you might do something that could result in equipment damage or loss of
data.
1 Product Overview
Launched by Ruijie independently, RG-S8600E series next generation core switches adopt the Full Mesh/Clos architecture and
support large buffer. RG-S8600E series support dual supervisor modules and power supply redundancy, which are available in three
models, namely, RG-S8605E, RG-S8607E, RG-S8610E and RG-S8612E.
RG-S8605E adopts Full Mesh architecture and supports dual supervisor modules and provides 3 slots for service modules.
RG-S8607E adopts Full Mesh architecture and supports dual supervisor modules and provides 5 slots for service modules.
RG-S8610E adopts Clos architecture and supports dual supervisor modules and provides 8 slots for service modules.
RG-S8612E adopts Clos architecture and supports dual supervisor modules and provides 8 slots for service modules.
2 Safety Precautions for Movement
RG-S8600E series is large and heavy. When you carry them, please pay attention to the following requirements:
Unplug all power cords before you move the switch. Note: There may be more than one power cord.
Remove the power supply, fans and service modules to reduce the chassis weight before moving the switch for a long distance.
At least 4 people are needed to move the switch.
Keep balance when moving the switch by 4 people, and keep the pace with each other.
Grasp the handles on both sides of the chassis, not the power supply handle, fan handle or the rear panel handle. Those handles
are just used to install and remove corresponding parts, and cannot bear the whole switch weight.
The whole switch weight may be higher than 80 kg during the movement.
To correctly move the RG-S8605E, refer to the Figure 2-1. For the RG-S8607E, refer to Figure 2-2. For the RG-S8610E, refer to
Figure 2-3. And for RG-S8612E, refer to Figure 2-4.
Note that the following figures are just the schematic diagrams, do not insert the line card and power supply when moving the
chassis to avoid the chassis weight increment or line card damage.
Figure 2-1 Moving the RG-S8605E Switch
Figure 2-2 Moving the RG-S8607E Switch
·
Figure 2-3 Moving the RG-S8610E Switch
Figure 2-4 Moving the RG-S8612E Switch
·
3 Preparations Before Installation
3.1 ESD Prevention
Precaution
To avoid the damages from static electricity to the internal parts of switches, do as follows:
ESD prevention measures are taken in the sites where switches are installed.
Wear the antistatic wrist strap while installing various switch parts, especially when you may touch circuit boards with hands.
Grasp the edge of modules. Do not touch the parts or printed circuits directly.
Wearing the anti-static wrist strap
The antistatic wrist strap is shipped with RG-S8600E, which is used as follows:
1. Stretch out your hand into the antistatic wrist strap.
2. Lock the wrist strap and make sure that the metal part of the antistatic wrist strap is in good contact with skin.
3. Insert the antistatic wrist strap in the antistatic wrist strap jack of the switch chassis or clip on the grounding pole of the chassis.
The antistatic wrist strap jack is located on the front panel of the chassis marked with yellow ESD.
4. The antistatic wrist strap is grounded well and the DC electric resistance between the body and the ground is in the range of 1 to
10 mega ohms.
Figure 3-1 ESD Prevention on RG-S8605E
·
Figure 3-2 ESD Prevention on RG-S8607E
Figure 3-3 ESD Prevention on RG-S8610E
·
Figure 3-4 ESD Prevention on RG-S8612E
·
3.2 Installation Site
RG-S8600E series must be used in the room. To ensure normal operation and a prolonged use life of the device, the installation site
must meet the requirements of weight capacity, humidity , cleanness, EMI consideration, grounding system, power, and ventilation.
See the Preparation before Installation chapter of RG-S8600E Series Switches Hardware Installation and Reference Guide for details.
3.3 Cabinet Mounting
Make sure the cabinet complies with the following conditions:
Install the switch in a 19-inch cabinet in 4-port form hold.
Be sure the distance between two square hole strips, one on each side, is 465 mm.
Figure 3-4 19-inch Cabinet
·
Be sure that the square hold strip is at least 180 mm far from the outboard front door and the door is at most 25 mm thick to
ensure a minimum available distance of 155 mm. The front door is at least 1000 mm far from the back door,
Figure 3-5 Cabinet Dimensions
Be sure that the slide rail in the cabinet is enough to bear the weight of a RG-S8600E and its installation accessories.
Inhaltsverzeichnis
Andere Ruijie Schalten Handbücher
Ruijie
Ruijie RG-NBS3100 Series Anleitung zur Verwendung
Ruijie
Ruijie RG-S6510-48VS8CQ Installations- und Betriebsanleitung
Ruijie
Ruijie RG-S2910-24GT4SFP-UP-H Installations- und Betriebsanleitung
Ruijie
Ruijie RG-S6220-H Series Bedienungsanleitung
Ruijie
Ruijie RG-CS83 Series Bedienungsanleitung
Ruijie
Ruijie RG-CS86 Series Installations- und Betriebsanleitung
Ruijie
Ruijie RG-N18000-XH Series Installations- und Betriebsanleitung
Ruijie
Ruijie RG-S5750-E Series Installations- und Betriebsanleitung
Ruijie
Ruijie RG-S6980-64QC Installations- und Betriebsanleitung
Ruijie
Ruijie RG-CS83-24GT4XS-PD Installations- und Betriebsanleitung
Ruijie
Ruijie RG-SF2920 Series Installations- und Betriebsanleitung
Ruijie
Ruijie RG-SF2920U Series Installations- und Betriebsanleitung
Ruijie
Ruijie RG-CS85 Series Installations- und Betriebsanleitung
Ruijie
Ruijie Reyee RG-NIS Series Bedienungsanleitung
Ruijie
Ruijie RG-S6510-32CQ Installations- und Betriebsanleitung
Ruijie
Ruijie Reyee RG-ES106D-P V2 Bedienungsanleitung
Ruijie
Ruijie S8600E Series Betriebsanleitung
Ruijie
Ruijie RG-NIS3100 Series Installations- und Betriebsanleitung
Ruijie
Ruijie RG-MF2920U Series Installations- und Betriebsanleitung
Ruijie
Ruijie RG-CS88-08 Series Installations- und Betriebsanleitung
