Samsung SR20H9050U Bedienungsanleitung

SR20H9050U Series

SR20H9030U Series

POWERbot

user manual

imagine the possibilities

Thank you for purchasing a Samsung product.

English

Before operating this unit, please read the instructions carefully.

For indoor use only.

SR20H9050U_EN_DJ68-00716G-00_EU.indd 29 2014-08-18 오후 6:03:46

ENGLISH-02

Contents 03 Safety information

08 Installation

Accessories / Installation note

10 Charging

Automatic charging / Recharging / Low

battery (Lo)

12 Installing the Virtual guard

Part name of the Virtual guard /

Inserting batteries

14 Using POWERbot

Turning the power on/off / Using Auto

clean mode / Using the cleaning modes /

Recharging

16 Using the remote control

Power/Recharging / Cleaning mode /

Additional function / Direction control /

Point cleaning

18 Name of each part

Top / Bottom / Display panel

19 Setting time/schedule

Setting the time / Setting the schedule

20 Cleaning and maintaining

Cleaning the dustbin / Cleaning the sensors

and the camera / Cleaning the Power brush /

Cleaning the Driving wheel

22 Notes and cautions

Charging / In use / Cleaning and maintenance /

About battery / About the IrDA sensor

24 Error codes

25 Troubleshooting

26 Open Source Announcement

27 Specifications

SR20H9050U_EN_DJ68-00716G-00_EU.indd 2 2014-08-18 오후 6:03:30

ENGLISH-03

Safety information

SAFETY INFORMATION

WARNING

• Before operating the appliance, please read this manual thoroughly and retain it

for your reference.

WARNING

• Because these following operating instructions cover various models, the

characteristics of your vacuum cleaner may differ slightly from those described in

this manual.

CAUTION/WARNING SYMBOLS USED

WARNING

Indicates that a danger of death or serious injury exists.

CAUTION

Indicates that a risk of personal injury or material damage exists.

OTHER SYMBOLS USED

NOTE

Indicates that a risk of personal injury or material damage exists.

SR20H9050U_EN_DJ68-00716G-00_EU.indd 3 2014-08-18 오후 6:03:30

ENGLISH-04

Safety information

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic precautions should be observed, including the

following:

READ ALL INSTRUCTIONS BEFORE USING YOUR POWERbot.

Unplug from outlet when not in use and before conducting maintenance.

WARNING: to reduce the risk of fire, electric shock, or injury:

GENERAL

•Use only as described in this manual.

•Do not operate POWERbot or charger (station) if it has been damaged in any way.

•If the vacuum cleaner is not working as it should, has been dropped, damaged, left

outdoors, or dropped in water, return it to a customer care center.

•Do not handle the charger (station) or POWERbot with wet hands.

•Use only on dry, indoor surfaces.

•This appliance can be used by children aged from 8 years and above and persons with

reduced physical, sensory or mental capabilities or lack of experience and knowledge

if they have been given supervision or instruction concerning use of the appliance in a

safe way and understand the hazards involved.

•Children shall not play with the appliance. Cleaning and user maintenance shall not be

made by children without supervision.

BATTERY Charger (station)

•Do not modify the polarized plug to fit a non-polarized outlet or extension cord.

•Do not use outdoors or on wet surfaces.

•Unplug the charger (station) from the outlet when not in use and before servicing.

•Use only the charger (station) supplied by the manufacturer to recharge.

•Do not use with a damaged cord or plug or a loose power outlet.

•Do not pull or carry by the cord, use the cord as a handle, close the door on the cord,

or pull the cord around sharp edges or corners. Keep the cord away from heated

surfaces.

•Do not use extension cords or outlets with inadequate current carrying capacity.

•Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord.

•Do not mutilate or incinerate batteries as they will explode at high temperatures.

•Do not attempt to open the charger (station). Repairs should only be carried out by a

qualified customer care center.

•Do not expose the charger (station) to high temperatures or allow moisture or humidity

of any kind to come into contact with the charger (station).

SR20H9050U_EN_DJ68-00716G-00_EU.indd 4 2014-08-18 오후 6:03:30

ENGLISH-05

POWERbot

•Do not pick up hard or sharp objects such as glass, nails, screws, coins, and etc.

•Do not use without a filter in place. When servicing the unit, never put fingers or other

objects into the fan chamber in case the unit accidentally turns on.

•Do not put any objects into openings. Do not use with any openings blocked; keep

openings free of dust, lint, hair, and anything that may reduce air flow.

•Do not pick up toxic materials (chlorine bleach, ammonia, drain cleaner, etc.).

•Do not pick up anything that is burning or smoke, such as cigarettes, matches, or hot

ashes.

•Do not use to pick up flammable or combustible liquids such as gasoline, nor use on

areas where they may be present.

•Locations with candles or desk lamps on the floor.

•Locations with unattended fires (fire or embers).

•Locations with distilled alcohol, thinner, ashtrays with burning cigarettes, etc.

•Do not use POWERbot in an enclosed space filled with vapours given off by oil based

paint, paint thinner, moth proofing substances, flammable dust, or other explosive or

toxic vapours.

•Leaks from battery cells can occur under extreme usage or temperature conditions.

If the liquid gets on skin, wash quickly with water. If the liquid gets into the eyes,

flush them immediately with clean water for a minimum of 10 minutes. Seek medical

attention.

SR20H9050U_EN_DJ68-00716G-00_EU.indd 5 2014-08-18 오후 6:03:30

ENGLISH-06

WARNING Power related

fPlease prevent any risk of electric shock or

fire.

– Do not damage the power cord.

– Do not pull the power cord too hard or touch

the power plug with wet hands.

– Do not use a power source other than 100-

240 V~ and also do not use a multi outlet to

supply power to number of devices at the same

time. (Do not leave the cord carelessly on the

floor.)

– Do not use a damaged power plug, power cord

or loose power outlet.

fClean dust or any foreign matters on the pin

and contact part of the power plug.

– There is a risk of electric shock or malfunction.

WARNING Before use

fDo not use POWERbot near combustible

materials.

– Place near candle, desktop lamps, fireplace or

near combustible materials such as gasoline,

alcohol, thinners etc.

fThe POWERbot is intended for household

use therefore do not use it in an attic,

basement, storage, industrial building, out of

indoor space, places with moisture (such as

bathroom, laundry), on the table or shelves.

– The POWERbot can be damaged or

malfunction.

fInstall the Virtual guard in front of dangerous

areas (such as stairs or railings) to prevent

damaging the product or getting injured.

– For your safety, always keep the cliff sensor

clean.

fBe sure POWERbot does not pass through or

touch any kind of liquids.

– The POWERbot can be severely damaged and

it may contaminate other areas if the wheels

pass through liquid.

fDo not spill any liquids on the charger.

– There is a risk of fire or electric shock.

fDo not use the charger for anything other

than its intended purpose.

– There is a risk of fire or severe damage to the

charger.

fAlways keep the cliff sensor clean for your

safety.

WARNING In use

fIf any abnormal sounds, smells or smoke

come from POWERbot, immediately shut

off the emergency switch at the bottom of

POWERbot and contact a service center.

WARNING Cleaning and

maintenance

fWhen power cord is damaged, contact a

service center to get it replaced by certified

repairman.

– There is a risk of fire or electric shock.

fPlease check with a Samsung Electronics

service center when exchanging batteries.

– Using batteries from other products can cause

malfunction.

Safety information

SR20H9050U_EN_DJ68-00716G-00_EU.indd 6 2014-08-18 오후 6:03:30

ENGLISH-07

CAUTION Before use

fInsert the dustbin before using POWERbot.

fOpen room doors before cleaning in order

to have all rooms cleaned and install a

Virtual guard in front of entryway, balconies,

bathrooms, or other areas where POWERbot

may fall.

fBe careful with the followings for proper

automatic recharging.

– Always turn on the power of the charger.

– Install the charger where POWERbot can easily

find.

– Do not leave any object in front of the charger.

fWhen installing the charger, do not leave the

cord carelessly on the floor since POWERbot

may get tangled by it.

fDo not use POWERbot on black colored

floors.

– The POWERbot may not be able to operate

normally.

fDo not pick up POWERbot by the dustbin

holder.

fDo not place any objects within 0.5 m to both

sides and 1 m to the front of the charger.

fMake sure the charger's charging contact is

not damaged or have any foreign matters on

it.

fDo not install the charger in an area with a

dark floor.

– If the floor around the charger is dark,

recharging is hindered.

fMove any obstacles that may disturb

POWERbot's movement (such as children's

indoor swing or slides) before cleaning.

CAUTION In use

fUsing POWERbot on thick carpet may

damage both POWERbot and the carpet.

– The POWERbot cannot pass over carpet that is

thicker than 1 cm.

fDo not use POWERbot on tables or other

high surfaces.

– There is a risk of damage if it falls.

fThe POWERbot may bump into chair, desk

legs therefore move them away for faster and

efficient cleaning.

fWhen POWERbot is operating, do not lift it up

or carry it to another area.

fDo not hold by driving wheels of POWERbot

when carrying it to another area.

fDo not put any objects on top of POWERbot

since it may cause malfunction.

fRemove any large papers or plastic bags

immediately when using POWERbot since

they may block the intake.

fDo not aim the red pointer directly at people

or animals.

CAUTION Cleaning and

maintenance

fPrevent any damage to POWERbot by

complying the followings.

– Do not clean POWERbot by spraying water

directly onto it or use benzene, thinner, acetone

or alcohol to clean it.

fDo not disassemble or repair POWERbot.

This should only be done by a certified

repairman.

fAlways keep the obstacle sensor and cliff

sensor clean.

– If foreign matter accumulates, sensors may

malfunction.

SR20H9050U_EN_DJ68-00716G-00_EU.indd 7 2014-08-18 오후 6:03:30

ENGLISH-08

1Connect the

adapter jack to

the charger 2Connect the

power cord to

the adapter

When using the adapter,

the side with the sticker

attached must face down.

3Connect the

power plug to

the outlet

Power lamp (Red) will turn

on.

Installation

Power of the charger must be on at all times.

DC-IN

Power lamp (Red)

About 1 m

About 0.5 m

Install it in a place without obstacles

and danger of falling.

SR20H9050U_EN_DJ68-00716G-00_EU.indd 8 2014-08-18 오후 6:03:31

ENGLISH-09

Accessories

Remote control Batteries (AAA type) User manual/Quick

guide

Spare filter

Cleaning brush Power cord Adapter Virtual guard

Installation note

Note

fInstall charger in a place where the floor and wall are level.

fIt is best to install the charger along the grain of wooden floors.

fIf the emergency switch is off, POWERbot will not charge even if it is docked on the charger.

fAlways turn on the power of the charger.

– If power is not supplied to the charger, POWERbot cannot find it and cannot automatically recharge.

– If POWERbot is left detached from the charger, the battery will drain naturally.

fIf POWERbot is in energy-saving mode, power will not come on even if the emergency switch is

turned off and then on. Press and hold the [Start/Stop] button on POWERbot.

SR20H9050U_EN_DJ68-00716G-00_EU.indd 9 2014-08-18 오후 6:03:31

ENGLISH-10

Charging lamp during charging (green)

It takes approximately 160 minutes to

completely charge when charging for the

first time after purchase and can be used for

approximately 60 minutes.

Charging

1Turn on the

emergency switch

on the bottom

You must turn on the

emergency switch to turn on

POWERbot.

2Manually charge

POWERbot by

placing it on the

charger

Make sure charge pins of

POWERbot and the charger is

aligned.

3Check the

charging status

“ ” will turn on

according to charging

progress and "FULL" will

turn on when charging is

complete.

WARNING

• Rated input voltage of this product

is 100-240 V~.

SR20H9050U_EN_DJ68-00716G-00_EU.indd 10 2014-08-18 오후 6:03:32

Andere Handbücher für SR20H9050U

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Samsung Staubsauger Handbücher

Samsung

Samsung VCDC13 Series Bedienungsanleitung

Samsung

Samsung SC7030 Bedienungsanleitung

Samsung

Samsung VAC-5800 SERIES Merkblatt

Samsung

Samsung POWERbot SR10M70 Series Bedienungsanleitung

Samsung

Samsung Vacuum cleaner Bedienungsanleitung

Samsung

Samsung SU4341 Bedienungsanleitung

Samsung

Samsung SC6780 Bedienungsanleitung

Samsung

Samsung VC-6000 SERIES Bedienungsanleitung

Samsung

Samsung SU8860 Bedienungsanleitung

Samsung

Samsung SU12F40SD Bedienungsanleitung

Samsung

Samsung SC06H70 0H Series Bedienungsanleitung

Samsung

Samsung VS60K6030KY Bedienungsanleitung

Samsung

Samsung SC6540 Bedienungsanleitung

Samsung

Samsung SC07M31 Series Bedienungsanleitung

Samsung

Samsung SU-2910 Series Bedienungsanleitung

Samsung

Samsung VCJG Series Bedienungsanleitung

Samsung

Samsung POWERbot SR2AH905 Series Bedienungsanleitung

Samsung

Samsung SC61 Series Bedienungsanleitung

Samsung

Samsung Vacuum cleaner Bedienungsanleitung

Samsung

Samsung Jet 60 Pet Bedienungsanleitung

Samsung

Samsung Vacuum cleaner Bedienungsanleitung

Samsung

Samsung VAC-9073R Merkblatt

Samsung

Samsung SR8875 Bedienungsanleitung

Samsung

Samsung Vacuum cleaner Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung

Nobles

Nobles 608669 Produkthandbuch