Samsung SU2913 Bedienungsanleitung

Vacuum

Cleaner

SU-2910 Series

FOR HOUSEHOLD USE ONLY

Operating

Instructions

IMPORTANT SAFETY INSTRUCTIONS ......................... 1

ASSEMBLING PARTS ..................................................... 2

ASSEMBLED VACUUM CLEANER PARTS .......................... 2

ATTACHING THE HANDLE ............................................. 2

ATTACHING THE HOSE AND TOOLS............................ 2

OPERATION .................................................................... 3

MAINTENANCE ............................................................... 4

TROUBLESHOOTING ..................................................... 6

Read these instructions before operating the vacuum cleaner

•The design and specification may be different depending on the models.

DJ68-00294L(0.5) 2009.5.21 11:4 AM 페이지1 i n

IMPORTANT SAFETY INSTRUCTIONS

Thank you for purchasing a Samsung vacuum cleaner. When using an electrical

appliance, basic precautions should always be followed, including the following :

PLEASE READ ALL WARNINGS AND INSTRUCTIONS BEFORE

USING THIS VACUUM CLEANER.

WARNING:

To reduce the risk of fire, electric shock, or injury :

• Do not leave vacuum cleaner unattended when it is plugged in.

• Unplug from outlet when not in use and before servicing.

• Do not use outdoors or on wet surfaces.

• Use only as described in this manual. Use only manufacturer’s recommended attachments.

• If vacuum cleaner is not working as it should, or has been dropped, damaged, left outdoors or

dropped into water, return it to a service center.

• Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull the cord

around sharp edges or corners. Keep cord away from heated surfaces.

• Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord.

• Do not handle vacuum cleaner or plug with wet hands.

• Do not put any object into openings. Do not use with any opening blocked; keep openings free

of dust, lint, hair and anything that may reduce air flow.

• Keep hair, loose clothing, fingers and all parts of body away from openings and moving parts.

• Do not pick up anything that is burning or smoking, such as cigarettes, matches or hot ashes.

• Do not use without dirt cup or filters in place. Empty dirt cup and clean filter frequently when

picking up very fine materials such as powder.

• Turn off all controls before unplugging vacuum cleaner.

• Use extra care when cleaning on stairs.

• Do not use to pick up flammable or combustible materials such as gasoline or fine wood, fine

wood sandings or use in areas where they may be present.

• Store your vacuum cleaner indoors, in a cool and dry area.

• Avoid picking up hard, sharp objects with the cleaner. They may damage the cleaner.

• Always turn off this appliance before connecting or disconnecting the hose, removing the

bottom plate for maintenance.

• Use only on dry, indoor surfaces, never change the plug in any way.

• Do not modify the polarized plug to fit a non-polarized outlet or extension cord.

• Do not touch the brush roller when it is rotating.

• Keep suction away from your face when using nozzles and pipe.

• Do not pull the power cord around sharp corners and do not allow it to be trapped.

• Unplug before connecting turbine nozzle.(only using turbine-brush model)

•

This appliance is not intended for use by persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge, unless they have been given

supervision or instruction concerning use of the appliance by a person responsible for their safety.

• Children should be supervised to ensure that they do not play with the appliance.

•

The plug must be removed from the socket-outlet before cleaning or maintaining the appliance.

• If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or

a similarly qualified person in order to avoid a hazard.

SAVE THESE INSTRUCTIONS

This vacuum cleaner is intended for household use only.

FOR RESIDENTS OF THE UNITED KINGDOM ONLY

If your appliance is fitted with a nonrewireable BS 1363 plug it must not be used unless a 13 amp

(ASTA approved to BS 1362) fuse is fitted in the carrier contained in the plug. If for any reason the

plug is cut off, it must be disposed of, as it is an electric shock hazard should it be inserted into a

13 amp socket.

DJ68-00294L(0.5) 2009.5.21 11:4 AM 페이지2 i n

Assembling Parts

Assembled Vacuum Cleaner Parts

The assembled cleaner will look

like the illustration to the left.

1. Handle

2. Power switch

3. Quick release cord hook

4. Post-Motor Filter

5. Crevice tool

6. Handle release

7. Carrying handle

8. Hose

9. Extension wand

10. Combination tool

11. Cyclone-Lever

12. Dirt Cup

13. Filter Cup

14. Upper Tank

15. Louvers

16. Hose Wand Base

17. Height Adjustment Dial

18. Hose Clip

WARNING!

OPERATE THE VACUUM CLEANER ONLY AT THE VOLTAGE SPECIFIED ON THE NAMEPLATE.

Front Back

Step 1. Attaching the Handle

Step 2. Attaching the Hose and Tools

Stand the vacuum upright and

slide the base of the handle

firmly into the grooves at the top

of the vacuum body.

Insert the screw provided into the

existing hole. Tighten the screw

securely with a screwdriver.

Before securing the handle,

please check that the handle is

fitted to the vacuum body and

make sure there’s no gap.

Slide the end of the hose

wand with tabs into the Hose

Wand Base.

Slide the extension wand

and the crevice tool together

into the storage clip.

1-1

1-2 1-3 1-4 1-5

Unless power switch is off or unplugged, the floor

brush will rotate while you use your vacuum

cleaner on carpet or floor.

For above floor cleaning, the floor brush will

continue to rotate but is raised above floor.

To prevent carpet damage, do not lean on the

vacuum or let the powerfoot tilt forward.

CAUTION

DJ68-00294L(0.5) 2009.5.21 11:4 AM 페이지3 i n

Operation

When using the attachments, ensure

the vacuum cleaner is placed firmly on

the floor with the handle in the upright

position. Do not place the vacuum on top of

furniture or steps as the brushroller may

cause damage.

A. Combination tool:

Two types of cleaning tools are included in

one attachment: rotate for desired tool.

·Use brush side to dust furniture,

blinds, books, lamps, shelves.

·Use upholstery side for curtains,

draperies, cushions, fabrics.

B. Crevice tool:

Use in corners, on stairs, baseboards, and

behind furniture.

C. Extension Wand:

Use with desired attachments and narrow

wand for a longer reach.

󳢬󳢬option

D. Mini Turbo Brush (Select Models) :

Use rotating brush action for small areas

such as stairs and upholstery.

Note: Press gently when using Mini Turbo

Brush to gain maximum cleaning. Too much

pressure could cause the brush to stop rotating.

E. Wooden Floor Brush (Select Models):

Use for bare floors. Swivel head turns to

get into tight spaces and fits under cabinets.

Note: The Wooden Floor Brush does not

store on board.

2-1 2-2 2-3

Carrying handle

The cleaner can also be moved by

using the carrying handle.

2-4 2-5

Cleaning lightweight

flexible rugs

Stand on one end of rug and move

cleaner toward other end or edge.

Before reaching edge, push down on

handle. This will lift up the nozzle(front of

cleaner)and will prevent rug from clinging

to cleaner.

Continue to lift front of cleaner so that

when you have reached the edge, it is

completely off the rug. Move cleaner

back to start again, lower front of cleaner,

and use only forward strokes.

Carpet height adjustment

Carpet and rug cleaning takes place at the

nozzle (A).

When it is necessary to raise and lower the

nozzle for various carpet pile heights, rotate the

nozzle control dial (B) to the desired setting.

For maximum cleaning performance, The

following carpet height settings are recommended:

·Lowest setting: for all types of carpet

·Higher settings: for very deep pile carpet where

easier pushing effort is desired, while maintaining

good cleaning performance.

Note: If the cleaner is difficult to push, rotate knob to

the next higher setting.

2-6

2-7

2-8

ON-OFF Switch

1.To turn cleaner on, press the

Power switch.

2.To the cleaner off, press the

Power switch again.

Handle positions

The handle of your cleaner has

three positions; upright for storage

and when using cleaning tools;

operating for general operation on

carpet and floors; low for reaching

under low furniture. Step on handle

release pedal to lower handle.

Transporting cleaner

To move your cleaner from room to

room, put the handle in upright

position, tilt the cleaner back on its

rear wheels and push forward.

󳢬󳢬option

Cleaning Tool attachments

Attachment tools can be used to

clean furniture or drapes, on stairs

or in corners.

DJ68-00294L(0.5) 2009.5.21 11:4 AM 페이지4 i n

Maintenance

Familiarize yourself with these home maintenance tasks as proper use and care of your cleaner will ensure continued

cleaning effectiveness.

When to empty the Dirt Cup

The dirt cup needs to be emptied when the dirt reaches the "MAX" line on the side of the Cup.

If more dirt than this accumulates, your cleaner will not operate effectively.

Note: All new carpet has loose fibers which can fill the Dirt Cup quickly while vacuuming.

Emptying the Dirt Cup

Disconnect cleaner from electrical outlet.

Slide the Cyclone-Lever to the

"Unlock" position.

Grasp handle and pull the Dirt

Cup straight out to remove from

Vacuum.

Empty dirt into garbage container.

Put the Dirt Cup back in the

vacuum and slide the lever to the

"Lock" position.

Cleaning The Circular

Filters.

Grasp the Filter Cup located at

the bottom of the Dirt Cup and twist

counterclockwise to unlock and

remove.

3-1 3-2 3-3

Cleaning the Pre/Post-motor Filter

How to clean

Disconnect cleaner from

electrical outlet.

The Pre-Motor Filter protects the

Motor from debris.

It is located underneath the Dirt

Cup and Filter Cup in the

Center of the round part of the

Cyclone-Lever.

Remove the small round Filter

and any debris on top of it. Rinse

well under warm water, then air

dry thoroughly before replacing.

The Post-Motor Filter assists in the

filtration process to return clean air

to the room. It is located behind the

door on the front of the Cleaner.

When the filter becomes dirty,

The Micro-Filter : Open the door,

remove the filter and shake the

dust off the filter.

The Micro-Filter is non-washable,

therefore do not wash it in water.

The Hepa-Filter(Select Models) :

Open the door, remove the filter

and replace.

The Hepa-Filter is not washable

and must be replaced.

Replace the door by inserting the

tabs on the left side and snapping

the right side into place.

3-5 3-6

Grasp the Circular Filters and twist

to unlock Pull straight up to

remove.

Separate the Outer foam and Inner

pleated Circular Filters.

Wash each individually by hand

in warm water. Mild detergent may

be used if desired.

Rinse well, then air dry Thoroughly

dry before putting them back

together and replacing in the Filter

Cup The Filter Cup may be

washed In warm water with a mild

detergent. Make sure it is

completely dry before

reassembling with fliters.

Do not operate cleaner without

Either the Pre-Motor Filter or

Post-Motor Filter in place.

Post-Motor Filter

Hepa-Filter

Micro-Filter

3-4

Pre-Motor

Filter

Unlock

Position

Lock

Position

MAX Line

DJ68-00294L(0.5) 2009.5.21 11:4 AM 페이지5 i n

Maintenance

The belt

The belt on your cleaner causes the

agitator to rotate and is important for

the effective operation of the

cleaner. The belt is located under

the bottom plate of the cleaner and

should be checked from time to time

to be sure it is in good condition.

When to replace

Disconnect cleaner from

electrical outlet.

To check belt, remove bottom plate

as shown in “How to replace.”

Replace belt if it is stretched, cut or

broken.

Remove agitator and used belt.

Discard used belt.

3-7 3-8

Insert agitator through belt and place

belt in belt guide (C) on agitator.

Should the agitator shield (D)

become dislodged while replacing

the belt or the agitator, reposition it

as shown, noting the placement of its

belt guide (E)

When to replace the

agitator brush roll

When agitator brushes are worn, the

agitator should be replaced.

To check condition of brushes,

disconnect cleaner from electrical

outlet.

Move the edge of a card across

bottom plate while turning agitator.

To maintain cleaning effectiveness,

replace agitator if brushes do not

touch card.

Grasp agitator firmly and fit it into

position by first sliding the end opposite

the belt into the rectangular slot (F) on

side of cleaner.

Pull other side of agitator (G) into place.

Turn agitator, making sure belt is not

pinched between agitator and agitator

shield.

3-10

With lettering on outside of belt and

positioned as shown in box on (D),

slide new belt over motor pulley (B).

3-9

3-11

How to replace

Disconnect cleaner from electrical

outlet.

Remove bottom plate, belt and

agitator following directions in “The

belt” section beginning with Fig. 3-10.

Discard old agitator.

Continue following the directions in

“The belt” section to reposition belt,

new agitator and bottom plate.

Reposition bottom plate and 5

screws. Tighten screws securely.

3-12 3-13

How to replace

Disconnect cleaner from electrical

outlet.

Place handle in low position and turn

cleaner over so bottom side is up.

Remove the 5 screws as shown with

a screw driver.

DJ68-00294L(0.5) 2009.5.21 11:4 AM 페이지6 i n

Maintenance

Troubleshooting

Clearing Blockages

Disconnect cleaner from electrical outlet.

The hose on the back of the vacuum cleaner that carries the dirt from the nozzle to the Dirt Cup can

sometimes become clogged. If you notice a change in the sound of the vacuum motor, check for blockages.

Check this list of possible problems and solutions before bringing your vacuum to a service center.

Remove the Hose and disconnect

the Wand.

Check for clogs in the vacuum

base, the wand, the hose and the

suction inlet.

If the blockage persists, turn the

vacuum cleaner off and unplug it.

Remove the bottom plate. Lift up

the short hose in the base of the

vacuum. Inspect the hose for clogs

and remove any obstructions.

Replace the short nozzle hose and

the bottom plate.

Remove Dirt Cup and check Upper

Tank and Louvers.

Check to make sure Louvers are

Installed correctly. To unlock the

Louvers, grasp the rim and turn

Toward the left. Pull straight down

to remove. If the Louvers are

missing or not locked into place,

check and clear the tube in the

center of the Dirt Cup.

Problem: Cleaner won’t run

Possible Cause

Possible Solution

··Not firmly plugged in

··Plug unit in firmly

··No voltage in wall plug

··Check fuse or breaker

··Blown fuse or tripped breaker

··Replace fuse or reset breaker

··Filters blocked or dirty

··Clean filters as per manual instructions

Problem : Poor job of dirt pickup

Possible Cause

Possible Solution

··Full or clogged Dirt Cup

··Empty the Dirt Cup and check for blockages.

··Broken or worn belt

··Replace belt.

··Clogged hose or nozzle

··Clean hose or nozzle area.

··Hole in hose

··Replace hose.

··Dirt Cup improperly installed

··Properly install the Dirt Cup

··Incorrect carpet height setting

··Rotate nozzle control knob to lower setting

··Clogs in air flow passage

··

Clear clogs/clean filters as per manual instructions

Possible Cause

Possible Solution

··Dirt Cup improperly installed

··Re-install the Dirt Cup.

Problem : Dust escapes the Dirt Cup

Possible Cause

Possible Solution

··Strange sound like rushing air

··Check for clogs in hose, nozzle area and or

filters, clear or claen any clogs or blockages

as per manual instructions

Problem : Abnormal sound

Possible Cause

Possible Solution

··Incorrect carpet height setting

··Rotate nozzle control knob to lower setting

Problem : Cleaner hard to push

3-14 3-16

3-15

DJ68-00294L(0.5) 2009.5.21 11:4 AM 페이지7 i n

THis Vacuum cleaner is approved the following.

Electromagnetic Compatibility Directive: 2004/108/EEC

Low Voltage Directive: 2006/95/EC

DJ68-00294L REV(0.5)

If you have any comments or questions regarding a Samsung products,

contact the SAMSUNG customer care center.

Country

U.K

SOUTH AFRICA

Customer Care Center ☎

0845 7267864 (SAMSUNG)

0860 7267864 (SAMSUNG)

Web Site

www.samsung.com/uk

www.samsung.com/za

Brush bar Replacement

Remove the tool from the hose,

and turn upside down. Slide the

switch to unlock position.

Remove bottom plate.

And remove brushbar and

discard.

Inspect belt to ensure that it is in

good condition. If broken or

cracked, please replace. (See

below for details.)

With the curved ends facing

down, slide end plates of

brushbar into slots on the tool.

To replace bottom plate, insert

the four tabs on edge of

bottom plate into slots on front

of tool. Pivot bottom plate

down and snap closed.

Use for upholstered furniture, carpeted stairs and hard-to-reach places.

3-17 3-18 3-19

Mini Turbo Brush (

󳢬󳢬

Option )

3-20 3-21 3-22

Belt Replacement

Grasp turbine and pull firmly to

remove.

Remove belt from turbine pulley.

Replace with new belt.

With flat sides of turbine

retainers pointing down, slide

retainers into grooves in tool

housing and snap into place.

Replace brushbar and bottom

plate.

Cleaning Brushbar

• Cut off pet hairs or threads

surrounding brush by using

scissors.

DJ68-00294L(0.5) 2009.5.21 11:4 AM 페이지8 i n

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Samsung Staubsauger Handbücher

Samsung

Samsung SC05K51 Series Bedienungsanleitung

Samsung

Samsung SC07M25E0WB Bedienungsanleitung

Samsung

Samsung VS15T70 Series Bedienungsanleitung

Samsung

Samsung VAC6013R Bedienungsanleitung

Samsung

Samsung Vacuum cleaner Bedienungsanleitung

Samsung

Samsung SU33xx SERIES Bedienungsanleitung

Samsung

Samsung SC07H40**V SERIES Bedienungsanleitung

Samsung

Samsung TC-9015VP Bedienungsanleitung

Samsung

Samsung POWERbot SR2AK9350W Series Bedienungsanleitung

Samsung

Samsung SC41 series Bedienungsanleitung

Samsung

Samsung Vacuum cleaner Bedienungsanleitung

Samsung

Samsung VC-7423V Bedienungsanleitung

Samsung

Samsung SC4580 Bedienungsanleitung

Samsung

Samsung Vacuum cleaner Bedienungsanleitung

Samsung

Samsung VS20T755 Series Bedienungsanleitung

Samsung

Samsung Vacuum cleaner Bedienungsanleitung

Samsung

Samsung V-KC681H Bedienungsanleitung

Samsung

Samsung VCMA15 Series Bedienungsanleitung

Samsung

Samsung SU2931 Bedienungsanleitung

Samsung

Samsung SC4520 Bedienungsanleitung

Samsung

Samsung POWERbot VR10M703PW9 Bedienungsanleitung

Samsung

Samsung SU33 SERIES Bedienungsanleitung

Samsung

Samsung SC05K71 H Series Bedienungsanleitung

Samsung

Samsung SC8421 Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

Exido

Exido 240-114 Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung