Sanitaire 800 Series Bedienungsanleitung

COMMERCIAL UPRIGHT

VACUUM CLEANER

OWNER’S GUIDE

800 SERIES

Index

Important Safeguards .......................... 2

General Information ............................. 6

Assembly ............................................. 6

Use....................................................... 8

Fan Chamber ..................................... 10

Dust Bag ............................................ 11

Brush Roll Belt ...................................12

Brush Roll (chrome steel) .................. 13

Brush Roll (anodized aluminum) 14

Headlight............................................ 14

Warranty............................................. 15

For location of nearest

Eureka/Sanitaire Warranty Station

or service information call

1-800-282-2886. www.eureka.com

Rating Plate

The model, type, and serial numbers are

indicated on the rating plate located on the

underneathsideofthecleaner. Forpromptand

complete service information, always refer to

these numbers when inquiring about service.

Model &Type ____________________

Serial No. _______________________

MODEL TYPE SERIAL NO.

VOLTS AMPS. HERTZ

SERVICE INFORMATION: 1-800-282-2886

IMPORTANT SAFEGUARDS

When using an electrical appliance, basic precautions should always be followed,

including the following:

READ ALL INSTRUCTIONS BEFORE USINGTHIS VACUUM CLEANER.

WARNING

To reduce the risk of fire, electric shock, or injury:

•Do not use outdoors or on wet surfaces.

•Do not leave vacuum cleaner when plugged in.Turn off the switch and unplug the

electrical cord when not in use and before servicing.

•Do not allow to be used as a toy.Close attention is necessary when used by or near

children.

•Use only as described in this manual. Use only manufacturer’s recommended

attachments.

•Do not use with damaged cord or plug. If vacuum cleaner is not working as it should,

has been dropped, damaged, left outdoors, or dropped into water, return it to a

service center before using.

•Do not pull or carry by cord, use cord as a handle, close door on cord, or pull cord

around sharp edges or corners. Do not run vacuum cleaner over cord. Keep cord

away from heated surfaces.

•Connect to a properly grounded outlet only (refer to Grounding Instructions).

•Do not use extension cords or outlets with inadequate current carrying capacity.

•Turn off all controls before unplugging.

•Do not unplug by pulling on cord.To unplug, grasp the plug, not the cord.

•Do not handle plug or vacuum cleaner with wet hands.

•Do not put any object into openings. Do not use with any opening blocked; keep

free of dust, lint, hair, and anything that may reduce airflow.

•This vacuum cleaner creates suction and contains a revolving brush roll.Keep hair,

loose clothing, fingers, and all parts of body away from openings and moving parts.

•Do not pick up anything that is burning or smoking, such as cigarettes, matches, or

hot ashes.

•Do not use without dust bag in place.

•Belt pulleys can become hot during normal use.To prevent burns, avoid touching

the belt pulley when servicing the drive belt.

•Use extra care when cleaning on stairs.

•Do not use to pick up flammable or combustible liquids such as gasoline, or use in

areas where they may be present.

•Store your cleaner indoors in a cool, dry area.

•Keep your work area well lighted.

•Unplug electrical appliances before vacuuming them.

SAVE THESE INSTRUCTIONS

Grounding Instructions

This appliance must be grounded. If it should malfunction or breakdown, grounding

providesapathofleastresistanceforelectriccurrenttoreducetheriskofelectricshock.

This appliance is equipped with a cord having an equipment-grounding conductor and

grounding plug. The plug must be plugged into an appropriate outlet that is properly

installed and grounded in accordance with all local codes and ordinances.

DANGER

Improper connection of an equipment-grounding conductor can result in risk of electric

shock. Check with a qualified electrician or service person if you are in doubt as to

whether the outlet is properly grounded. Do not modify the plug provided with the

appliance. If it will not fit the outlet, have proper outlet installed by a qualified technician.

This appliance is for use on a nominal 120 volt circuit and has a grounding plug that

lookslikethe plugillustratedinFigure A.Atemporaryadapterwhich looks likethe adapter

illustrated in Figure B may be used to connect this plug to a two-pole receptacle, as

shown, if a properly grounded outlet is not available.The temporary adapter should be

used only until a properly grounded outlet, Figure A, can be installed by a qualified

electrician.The green colored rigid ear, lug, or the like extending from the adapter must

be connected to a permanent ground such as a properly grounded outlet box cover.

Whenever the adapter is used, it must be held in place by a metal screw.

NOTE: In Canada, the use of a temporary adapter is not permitted by the Canadian

Electrical Code.

GROUNDED

OUTLET BOX GROUNDED

OUTLET BOX

FIGURE B

METAL

SCREW

ADAPTER

FIGURE A

GROUNDING BLADE

IS LONGEST OF THE

THREE BLADES

GROUNDING

TAB

CONSEILS DE SÉCURITÉ

Lors de l’utilisation d’un appareil électrique, quelques précautions élémentaires doivent

être observées, incluant les suivantes:

LISEZ TOUTES LES INSTRUCTIONS AVANT D’UTILISER VOTRE ASPIRATEUR.

AVERTISSEMENT

Pour réduire le risque de feu, de choc électrique, ou de blessure:

•Ne pas utiliser à l’extérieur ou sur des surfaces mouillées.

•Fermezlecommutateuretdébranchezl’appareillorsquevousnel’utilisezpasouavant

le nettoyage ou l’entretien.

•Nepermettezpasqu’ilsoitutilisé commejouet.Uneattentionparticulièreestnécessaire

lorsque utilisé par ou près d’un enfant.

•Suivez les recommandations d’utilisation de ce manuel. Utilisez uniquement les

accessoires recommandés par le fabriquant.

•Ne pas utiliser si le cordon ou la fiche sont endommagès. Si l’aspirateur ne fonctionne

pas comme il le devrait, s’il a été échappé, s’il est endommagé, s’il a été laissé à

l’extérieur ou échappé dans l’eau, retournez-le à un centre de service avant de utiliser.

•Ne pas le tirer ou le transporter par le cordon, ne pas utiliser le cordon en guise de

poignée. Ne pas fermer une porte sur le cordon ou tirer le cordon sur des coins ou

bordures pointus. Ne pas circuler sur le cordon avec l’aspirateur. Tenir le cordon à

distance des surfaces chauffantes.

•Branchez toujours l’aspirateur dans une prise à trois (mise à la terre).

•Ne pas utiliser des rallonges ou des prises qui n’ont pas de capacité suffisante pour

transporter le courant.

•Fermer tous les contrôles avant débrancher.

•Ne pas débrancher en tirant sur le cordon. Pour débrancher, tenez la fiche et non le

cordon.

•Ne pas manipuler la fiche ou l’aspirateur avec les mains mouillées.

•Nepasrien insérerdanslesouvertures.Nepasutiliser sidesouverturessontbloquées;

assurez-vous qu’elles soient dégagées de poussière, mousse, cheveux ou toute autre

chose qui pourrait réduire le passage de l’air.

•Cetaspirateurcréedelasuccionetcontientunrouleau-brossetournant.Tenirlesparties

mobiles et les ouvertures loin des cheveux, du linge, des doigts et de toute partie du

corps.

•Ne pas ramasser des objets qui brûlent ou fument comme les cigarettes, alumettes ou

cendres chaudes.

•N’utilisez pas sans le sac de poussière en place.

•Les poulies du courroie peuvent devenir chaudes pendant l’utilisation normale. Pour

prevenir des brûlures, évitez de touché la poulie du courroie lorsque vous réparez la

courroie.

•Portez une attention particulière lorsque vous nettoyez les escaliers.

•Ne pas utiliser pour ramasser des liquides inflammables ou combustibles comme de

l’essence: Ne pas utiliser dans les endroits où ces liquides pourraient être présents.

•Entreposez votre aspirateur à l’intérieur dans un endroit propre et sec.

•Maintenez un bon éclairage à l’endroit où vous travaillez.

•Débrancher les appareils électrique avant de les balayer.

CONSERVEZ CES INSTRUCTIONS

INSTRUCTIONS VISANT LA MISE À LA TERRE

Cet appareil doit être mis à la terre. En cas défaillance ou de panne éventuelles, la

mise à la terre fournit au courant un chemin de moindre résistance qui réduit le

risque de choc électrique. Cet appareil est pourvu d’un cordon muni d’un

conducteur de terre et d’une fiche avec broche de terre. La fiche doit être branchée

dans une prise appropriée correctement installée et mise à la terre conformément

aux règlements et ordonnances municipaux.

AVERTISSEMENT

Un conducteur de terre mal raccordé peut entraîner un risque de choc électrique.

Consulter un électricien ou un technicien d’entretien qualifié si vous n’étes pas certain

que la prise est correctement mise à la terre. Ne pas modifier la fiche fournie avec

l’appareil-si elle ne peut être insérée dans la prise, faire installer une prise adéquate

par un électricien qualifié.

Note. Au Canada, l’utilisation d’un adaptateur temporaire n’est pas autorisée par le

Code canadien de l’électricité.

Cet appareil est destiné à un circuit de 120 V et est muni d’une fiche de mise à la terre

semblable à celle illustrée par le Figure A. S’assurer que l’appareil est branché à une

prise de courant ayant la même configuration que la fiche.Aucun adaptateur ne devrait

être utilisé avec cet appareil.

FIGURE A

Boîte de Prise deTerre

LA LAME DE TERRE

EST LA PLUS LONGUE

DES TROIS LAMES

GENERAL INFORMATION

The cleaner is designed to pick up dirt and dust particles. Avoid picking up hard or

sharp objects with the cleaner to prevent bag tears, hose clogs, and fan blade breakage

with subsequent motor damage.

Service Information

The instructions in this booklet serve as a guide to routine maintenance. For additional

service information telephone our toll free number for the nearest Eureka/Sanitaire

AuthorizedWarranty Station. Refer toThe Sanitaire CommercialWarranty for complete

service information. You should know the model, type and serial numbers when

you call: USA: 1-800-282-2886

Mexico:5670-6169

Canada: 1-800-282-2886

DO NOT OIL the motor or the brush roll at any time. The bearings are

permanently lubricated and sealed.

Detail A

2-Part

Bolt

Cord

Hooks

Bag

Screws

Assembly Packet is with owner’s guide.

Step 1

Assemble the Handle

Slip the upper handle and the lower

handletogether sothe handleboltholes

align and the slots in the handle are

positioned as shown in Detail A. Insert

a 2-part bolt (A) in the center of the

handle and tighten.

Holdtheassembledhandlesoitcurves

away from the cleaner. Then push the

handle into the handle socket (D) at the

rear of the cleaner. Align the holes,

insert the other 2-part bolt (A), and

tighten.

HOW TO ASSEMBLE

The assembly packet contains two 2-

part bolts, 2 bag screws and two cord

hooks. An extra drive belt is also

included with some models.

Step 2

Attach Upper Cord Hook

Pull the spring on the electrical cord upward toward the

topofthe handle.Makesureslotsinhandlearepositioned

properly, see below.

Insert the lower half of the spring into the upper cord

hook (B), as shown.Snap the hook into the upper handle,

directions below.

Step 3

Attach Lower Cord Hook

Make sure cord hook is pointing

downwards. Press the power cord into the

groove on the cord hook pulling any slack

toward the base of the cleaner.On the cord

hook, find the curved tab and place in slot

on lower handle section, keep cord taut

while pressing the cord hook to the left until

it snaps into slot on opposite side of handle.

The hook should point downward on the

same side that the cord exits the hood.

Step 4

Attach Outer Bag

Important:To provide a good gasket seal,

the bag coupling must seat firmly

against the motor base.

Hold outer bag with zipper away from the

handle. Line up screw holes.Start the bag

screws by hand, then tighten with a

screwdriver.

Loop the bag spring onto the bag support

hook located at the back of the upper cord

hook.

BAG

SUPPORT

HOOK

3. SNAP opposite inner

tab into place

1. Place inner tab

into slot 2. Press hook

around handle

HOW TO USE

The upright vacuum cleaner is designed to be used on multiple types of carpeting.Do

not attempt to use the upright vacuum cleaner on bare floors, as damage to the

floor covering may result. Above the floor cleaning tools are available (optional).

Handle Adjustment

With the tip of the foot, press down to release the

handle lock located at the left rear side of the

cleaner.Movethe handle and adjust it tothe desired

position for (1) storing upright, (2) operating the

cleaner at a comfortable height for the user, and

(3) cleaning underneath low furniture.

Power Switch

The power switch is mounted on the motor hood near

the handle. Switch style varies by model and may differ

from the illustration.A push with the foot turns the motor

ON; push again to turn the motor OFF.

Edge Kleener®

Edge Kleener feature provides for improved cleaning of carpets near walls and

stationary furniture. Slots on the sides of the nozzle increase air flow to the edges of

the cleaner and add to the cleaning efficiency of the cleaner. To operate, simply run

cleaner along edge board. Edge Kleener operates instantly and automatically.

Handle Lock

1. Store

2. Use

3.Clean

Underneath

ON/OFF

Step 5

Store Electrical Cord

The cleaner has two convenient cord storage hooks attached to the handle.Wind the

cord around the hooks and fasten the plug to the cord to prevent unwinding.

HOWTO ASSEMBLE (continued)

Cleaner Height Setting

WARNING: Avoid injury.Keep loose clothing, hair,fingers, and all other parts of

body away from any moving part (such as the revolving brush).Turn

off the switch and unplug the cleaner before changing the cleaner

height setting.

Adjust the vacuum cleaner height

setting to match the carpet pile height.

Refer to the following chart of

recommendedsettings for carpettypes.

The front of the cleaner has either a

knob or slide adjustment which raises

or lowers the cleaner base to match the

type of carpet. With the cleaner cord

unplugged, set the adjustment

according to the table as a starting

point. While the cleaner is off and

disconnected from the outlet, place

the handle in the operating position, tilt

the cleaner back to remove the weight

from the wheels, and adjust the setting.Then plug the cleaner into the electrical outlet,

turn on the switch, lower the handle, and pass the cleaner over the carpet. If the

cleaner is still difficult to push, follow the procedure and test the cleaner at the next

higher setting. Continue testing the setting until the cleaner is comfortable to move.

Moving the knob or slide to the next higher setting raises the brush roll slightly, making

the cleaner easier to push.However, the brush roll must make contact with the carpet

for effective cleaning.

Recommended

Setting Example of Carpet

Position 1 Low pile as kitchen, indoor,

outdoor

Position 2 Sculptured

Position 3 Plush or thick sculptured

Position 4 Thick plush

Ifthe cleanerhas additionalheight settings,theyare forthicker

carpets or where easier pushing is desired.

HOWTO MAINTAIN

The instructions given in this booklet serve as a guide to routine maintenance. To avoid

unnecessary service calls, check the bag, belt and brush roll often.

Quick Kleen® Fan Chamber

NOTE: Turn off the switch and unplug the electrical cord before cleaning.

The clear, removable fan chamber cover provides easy

inspection, cleaning, and maintenance of the fan

chamber. Removing the cover provides easy access to

themotorfan. Greasebuildup,dirt, or other obstructions,

visiblethroughthe fancover, shouldberemoved. Toclean

thefanarea,takeoff thechrome bottomplatebyreleasing

the two cam locks (see Brush Roll Belt, Figure 1 and 2).

Remove the belt from the motor pulley, then loosen and

remove the screws on either side of the fan cover, as

indicated by the arrows. Push the cam locks outward

against the wheels to lift the cover from the cleaner base.

Dirt and obstructions can easily be cleared; however,

caked grease may need to be scraped from the cover

and the cleaner. If the fan does not turn freely, it also

should be removed for cleaning. To remove the fan, place a wrench over the motor

pulley. Hold thefan bladeswithonehand and turnthewrench counterclockwise. Remove

the motor pulley and lift the fan off the motor shaft. Clean the area and replace the fan

over the motor shaft. Tighten the motor pulley snugly clockwise with the wrench. If

necessary, replace the fan cover or the gasket with replacement parts.

Be sure the gasket is in place. Reposition the fan cover by first placing the exhaust end

into place between the large rear wheels. Seat the fan cover firmly. Next replace the

belt and bottom plate as the pressure from the bottom plate helps seal the fan cover.

Start the two screws by hand to be sure they are straight, then tighten.

Order fan chamber cover replacement kit (fan cover,gasket, two screws) Part No.

52334.

Cleaner Care

NOTE: Turn off the switch and unplug the electrical cord before cleaning unit.

To keep the vacuum cleaner looking new, it can be wiped with a damp cloth and a mild

soap solution, then thoroughly dried. Never use any type of chemical as chemicals can

damage the cleaner. When not in use, the cleaner should be stored in a clean, dry

place.

Andere Handbücher für 800 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sanitaire Staubsauger Handbücher

Sanitaire

Sanitaire Professional Upright Bedienungsanleitung

Sanitaire

Sanitaire 600 Series Bedienungsanleitung

Sanitaire

Sanitaire SC3680 Series Bedienungsanleitung

Sanitaire

Sanitaire SC695A - Sanitaire by - Commercial Upright Vacuum... Bedienungsanleitung

Sanitaire

Sanitaire SC886-E Bedienungsanleitung

Sanitaire

Sanitaire Quick Kleen SC886 Bedienungsanleitung

Sanitaire

Sanitaire PRECISION CANISTER SERIES Bedienungsanleitung

Sanitaire

Sanitaire SC412 Bedienungsanleitung

Sanitaire

Sanitaire SC412 Bedienungsanleitung

Sanitaire

Sanitaire 3700 Series Bedienungsanleitung

Sanitaire

Sanitaire SC6090 Handbuch

Sanitaire

Sanitaire Z4500 Series Bedienungsanleitung

Sanitaire

Sanitaire SC688B Bedienungsanleitung

Sanitaire

Sanitaire 670 Series Bedienungsanleitung

Sanitaire

Sanitaire SC679J - Maid Saver Upright Vacuum 5.0 Amp... Handbuch

Sanitaire

Sanitaire SC600 Series Bedienungsanleitung

Sanitaire

Sanitaire SC889 Series Bedienungsanleitung

Sanitaire

Sanitaire Quick Kleen SC899 Bedienungsanleitung

Sanitaire

Sanitaire SC5700 Series Bedienungsanleitung

Sanitaire

Sanitaire PRECISION UPRIGHT SERIES Bedienungsanleitung

Sanitaire

Sanitaire S634 System_Pro Bedienungsanleitung

Sanitaire

Sanitaire SC881A Handbuch

Sanitaire

Sanitaire 1040 Series Bedienungsanleitung

Sanitaire

Sanitaire 880 Series Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

Exido

Exido 240-114 Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung