Satel MICRA Bedienungsanleitung

Alarm module

with GSM/GPRS communicator

MICRA

Program version 2.02 micra_en 11/11

SATEL sp. z o.o.

ul. Schuberta 79

80-172 Gdańsk

POLAND

tel. + 48 58 320 94 00

[email protected]

www.satel.eu

WARNINGS

The device should only be installed by qualified personnel.

Read carefully this manual before proceeding to installation.

Changes, modifications or repairs not authorized by the manufacturer shall void your rights

under the warranty.

CAUTION!

It is not allowed to connect a fully discharged battery (with voltage across unloaded terminals

less than 11 V) to the module. In order to avoid any damage to the equipment, if the battery

is fully discharged, precharge it by means of a suitable charger.

The batteries contain lead. When used-up, the batteries must not be thrown away, but

disposed of as required by the existing regulations (European Directives 91/157/EEC and

93/86/EEC).

Due to the specific character of data transmission using GPRS

technology and possible costs involved, it is advisable to install in the

module a SIM card with tariff plan providing for at least 10 MB monthly

data transfer.

DECLARATION OF CONFORMITY

Product:

MICRA Manufacturer: SATEL spółka z o.o.

ul. Schuberta 79

80-172 Gdańsk, POLAND

tel. (+48 58) 320-94-00

fax (+48 58) 320-94-01

Product description: Alarm module with GPRS/SMS/CLIP communicator, built-in power supply and 433MHz

receiver, intended for intruder alarm systems.

The product is in conformity with the following EU Directives:

RTTE 1999/5/EC

EMC 2004/108/EC

LVD 2006/95/EC

The product meets the requirements of harmonized standards:

EMC/Immunity EN 50130-4:1995+A1:1998+A2:2003, EN 61000-6-1:2007

EMC/Emissions EN55022:2006+A1:2007, EN 61000-6-3:2007

Electrical safety EN 60950-1:2006

ETSI/EMC EN 301 489-7:V1.3.1, EN 301 489-1:V1.8.1

ETSI/Radio EN 301 511 V9.0.2, 3GPP TS 51.010-1 V5.10.0

Gdańsk, Poland 2010-10-11 Head of Test Laboratory:

MichałKonarski

The latest EC declaration of conformity and product certificates can be downloaded from our website

www.satel.pl

SATEL's goal is to continually improve the quality of its products, which may result in

alterations of their technical specifications and firmware. Current information on the

introduced modifications is available on our website.

Please visit us at:

http://www.satel.pl

Changes made to firmware version 2.02

Power The module can be powered with 12 V DC.

Clock When logging into GSM network, the module automatically downloads

time and date information, if such a service is offered by the GSM

network operator.

Relay outputs Capability of NC (normally closed) operating mode.

Ability to control outputs using the CLIP service.

Wireless

devices Support for new wireless devices:

1. wireless detectors

– MSD-300 smoke and heat detector,

– MPD-300 passive infrared detector,

– MMD-300 magnetic contact.

2. MKP-300 wireless keypad.

3. MPT-300 keyfob.

Arming /

disarming Capability of arming / disarming with the CLIP service.

Using the CLIP service or defined SMS message, the module can inform

about arming / disarming with the CLIP service.

SMS message

retransmission The module can forward received SMS messages to the specified

telephone numbers, which makes it possible e.g. to transmit information

received from the operator of GSM network in which the module

operates.

Status

messaging SMS message containing module status information has been

supplemented with:

– data on wireless zone status;

– information on exceeding the transmission limit.

Programming Programmability of some module parameters by SMS messages.

Parameters and

options Module with factory settings operates in the alarm device mode.

New option:

– ALARM IF ZONE VIOLATED AT THE END OF EXIT DELAY.

New parameter:

– LIMIT NUMBER OF NOTIFICATIONS TO.

GPRS-Soft

program Order of program tabs has been changed.

2 MICRA SATEL

CONTENTS

1. Module features ................................................................................................................3

2. Description of electronics board........................................................................................4

3. Installation.........................................................................................................................5

3.1 Installation plan..........................................................................................................6

3.2 Estimation of current consumption.............................................................................7

3.3 Cabling ......................................................................................................................7

3.4 The MICRA module installation .................................................................................7

3.5 Connecting detectors and other devices to zones .....................................................7

3.6 Connecting siren........................................................................................................8

3.7 Connecting power supply and starting the module ....................................................9

3.8 Wireless devices installation....................................................................................10

3.8.1 Adding new wireless devices............................................................................11

3.8.2 Removing wireless devices ..............................................................................11

4. Programming and configuring the module ......................................................................11

4.1 Local programming through RS-232 (TTL) port .......................................................11

4.2 Remote programming using GPRS technology .......................................................12

4.3 Description of the program ......................................................................................13

4.3.1 Main menu........................................................................................................13

4.3.2 „Options, zones, outputs” tab............................................................................15

4.3.3 „GSM telephone, Monitoring stations” tab ........................................................22

4.3.4 „Test transmissions” tab ...................................................................................26

4.3.5 „CLIP / SMS messaging” tab ............................................................................29

4.3.6 „Reporting” tab..................................................................................................30

4.3.7 „Keyfobs” tab ....................................................................................................32

4.3.8 „MKP-300 keypad” tab......................................................................................34

4.3.9 „Event log” tab ..................................................................................................36

4.4 Programming with the use of SMS messages .........................................................37

4.5 Configuring the module to work in alarm device mode ............................................37

4.6 Starting GPRS reporting ..........................................................................................38

4.7 Starting SMS reporting ............................................................................................38

4.8 Starting CLIP / SMS messaging ..............................................................................39

5. Restoring factory default settings....................................................................................39

6. Specifications..................................................................................................................40

SATEL MICRA 3

1. MODULE FEATURES

•4 individually programmable hardwired zones with optional operation in digital (NO, NC,

EOL) or analog mode.

•Additional TMP hardwired zone to supervise NO or NC wiring type:

– acting as a tamper loop input in communication device mode,

– programmable in alarm device mode.

•2 programmable NO or NC type relay outputs.

•OC type output serving as indicator of GSM network logging problems, or as armed mode

indicator.

•High-current (0.5 A) output, with polymer fuse, to perform the function of power supply

output (optionally, it can perform the power input function).

•Ability to remotely control the relay outputs with the CLIP service.

•Built-in radio waves superheterodyne receiver:

– support for up to eight 433 MHz keyfobs manufactured by SATEL;

– support for up to eight 433 MHz wireless detectors manufactured by SATEL;

– support for MKP-300 wireless keypad.

•Non-volatile 1024 event log buffer.

•Information on the status of supervised equipment and module through reporting in

Contact ID format (GPRS, SMS) or messaging (SMS, CLIP).

•Encrypted transmission of events sent with the use of GPRS technology.

•Capability to automatically replace the GPRS transmission with SMS message, if there are

problems with GPRS transmission.

•Periodical test transmissions for checking availability of the module:

– to selected telephone numbers (with the use of SMS message or CLIP service);

– to monitoring stations.

•Capability of generating additional test transmissions:

– after identification of the calling party's telephone number (CLIP service);

– after receiving command from the GPRS-SOFT program.

•Capability of arming / disarming the premises by means of CLIP service.

•Option to check the status of available resources and account validity of the SIM card

installed in the module.

•Listen-in feature for alarm verification by means of a telephone (external microphone

required).

•Module configuration:

– locally – through the RS-232 (TTL) port;

– remotely – through the GSM network (GPRS technology)

– remotely – using SMS messages.

•Indicator of GSM signal level received by industrial cellular telephone and an indicator of

troubles connected with logging into the GSM network.

•Automatic module restart capability.

•Switching mode power supply, output current 2 A with short-circuit protection, provided

with battery status monitoring and low battery disconnection circuit.

•Power supply with 18 V AC (±10%).

•Possibility to power with 12 V DC.

4 MICRA SATEL

2. DESCRIPTION OF ELECTRONICS BOARD

Fig. 1. View of module electronics board.

Explanations for Figure 1:

1 - superheterodyne receiver, high sensitivity, immune to spurious signals.

2 - battery connection cables

3 - LEDs indicating the module status. LED A is blinking when GPRS transmission is going

on. LED B is blinking when SMS message is being sent or the module is calling (CLIP

test transmission). The other LEDs indicate the level of signal received by the GSM

telephone. LEDs A and B blinking simultaneously indicate logging into the GSM

network. In case of an unsuccessful GSM network login, blinking of the other LEDs

provides information on the troubles (see: Fig. 2).

4 - port RS-232 (standard TTL) enables local programming by means of the GPRS-SOFT

program (connection can be made with cables included in the set manufactured by

SATEL and designated DB9FC/RJ-KPL).

5 - SIM card socket. It is not recommended to insert the SIM card into its socket before

programming the card PIN code in the module (if the card requires entering the PIN

code). If the event codes are to be sent with the use of GPRS technology, the GPRS

service must be activated for the SIM card installed in the module.

6 - GSM industrial telephone.

7 - microphone socket. The microphone enables the listen-in feature (it is recommended

to use an electret microphone).

8 - antenna socket. Be careful when connecting the antenna so as not to damage the

socket.

SATEL MICRA 5

Fig. 2. Examples of LED indicated statuses. A (LED A is blinking, the other LEDs are lit

up) – GPRS transmission is going on; signal level: 3. B (LED B is blinking, the other LEDs

are lit up) – SMS message is being sent or module is calling (CLIP test transmission); signal

level: 4. C (LEDs are blinking) – logging into GSM network. D (LEDs are blinking) –

logging into GSM network has failed; missing SIM card. E (LEDs are blinking) – logging into

GSM network has failed; missing PIN code. F (LEDs are blinking) – logging into GSM

network has failed; invalid PIN code. G (LEDs are blinking) – logging into GSM network has

failed; SIM card has been blocked after three attempts to use an invalid PIN code (PUK code

must be used to unblock the SIM card).

Description of terminals:

AC - power supply inputs (18 V AC ±10%).

COM - common ground.

AUX - power supply output / input (12 V DC ±15%).

FT - OC type output (shorted to ground when active) to work as an indicator of

problems with logging into GSM network (it activates approx. 2 minutes of the

problem occurrence) or an armed mode indicator (with the ARM STATUS ON FT

OUTPUT option enabled). The problem with logging into the GSM network can

be caused by:

– unavailability of GSM network (out of range),

– missing or damaged antenna,

– entering an invalid PIN code,

– missing SIM card.

Some additional information can be provided by LEDs on the electronics board

(see: Fig. 2).

TMP - tamper zone (it can supervise the tamper contact of module enclosure,

detectors, sirens, etc.).

Z1 ÷ Z4 - zones.

NO1 - relay output terminals 1.

NO2 - relay output terminals 2.

3. INSTALLATION

All electrical connections may only be made with disconnected power supply.

Before connecting the power supply source (battery, alternating voltage from

transformer), you should first complete all the installation work.

The following tools will be useful during installation:

•blade screwdriver 2.5 mm,

•Phillips screwdriver,

6 MICRA SATEL

•precision pliers,

•flat nose pliers,

•drill with a set of drill bits.

Fig. 3. MICRA module with connected antenna, battery and transformer, installed in OPU-4 P

enclosure.

3.1 INSTALLATION PLAN

If the module is to be a component of alarm system, the installation should be preceded by

preparing a plan of arrangement in the premises of all devices to be included in such

a system, i.e. MICRA module, detectors, keypad and sirens.

SATEL MICRA 7

3.2 ESTIMATION OF CURRENT CONSUMPTION

Before proceeding to installation, sum up the currents consumed by all devices to be power

supplied by the module (the calculation should also take into account the battery charging

current.). The sum of such currents must not exceed the current output of the built-in power

supply. If the sum of currents exceeds the power supply current output, an additional power

supply unit must be used.

Note: When planning connection of devices to power output, remember that the sum of

currents consumed by these devices must not exceed the maximum current-carrying

capacity of this output.

3.3 CABLING

It is recommended that straight unscreened cable be used for making electric connections

(using the twisted pair type of cable, e.g. UTP, STP, FTP is not advisable). Select cross-

section of the power supply wires so that the supply voltage drop between the power supply

and the supplied device should not exceed 1 V as against the output voltage.

When making the cabling, remember that there must be sufficient distance between the low-

voltage wires and the 230 V AC power supply wires. Avoid running the signal cables in

parallel to the 230 V AC supply cables, in close vicinity of them.

3.4 THE MICRA MODULE INSTALLATION

The module PCB contains electronic components sensitive to electric charges.

The MICRA module should be installed indoors, in spaces with normal air humidity. The

installation place should be inaccessible to unauthorized persons. When selecting the

installation place, take into consideration that thick walls, metal partitions, etc. will reduce the

radio signal range. Installation in close vicinity of electrical systems is not recommended, as it

may adversely affect the device performance.

A permanent (non-disconnectable) 230 V AC power supply circuit with protective grounding

must be available at the module installation place.

3.5 CONNECTING DETECTORS AND OTHER DEVICES TO ZONES

Fig. 4. Loop types supervised by the alarm module.

The module zones can work as:

– digital, NC type – to supervise a device with normally closed contacts,

– digital, NO type – to supervise a device with normally closed contacts,

– digital, EOL type [only in alarm device mode] – to supervise a device with normally open

or closed contacts, where an 2,2 kΩEOL resistor is used,

8 MICRA SATEL

– analog [only in communication device mode] – to handle analog signals from devices

used in automation (measurement of temperature, pressure, rotation, etc.).

The devices to be connected to the zones can be supplied directly from the module (AUX

output) or from an additional power supply unit. The choice of the power supply source

should be made conditional upon the previous estimation of current consumption.

Fig. 5. An example of connecting NC type detector to the MICRA module (NO type detector

is to be connected in the same way).

3.6 CONNECTING SIREN

Relay outputs should be used to control a siren. The way in which the siren will be power

supplied should depend on an assessment of current consumption, which should be made

beforehand. The siren can be powered from the module AUX output, if the current

consumption by the siren does not exceed the output rating.

Fig. 6. Connection of the siren without own power supply (by example of SP-4001).

Andere Handbücher für MICRA

Inhaltsverzeichnis

Andere Satel Sicherheitssystem Handbücher

Satel

Satel SPL-5010 Bedienungsanleitung

Satel

Satel SPL-5010 Bedienungsanleitung

Satel

Satel SPW-100 Bedienungsanleitung

Satel

Satel ECAM22 Bedienungsanleitung

Satel

Satel CA-4M Bedienungs- und Wartungsanleitung

Satel

Satel ASP-200 Bedienungsanleitung

Satel

Satel ASP-105 Bedienungsanleitung

Satel

Satel SPW-150 Bedienungsanleitung

Satel

Satel SOW-300 Series Bedienungsanleitung

Satel

Satel ABAX 2 Bedienungsanleitung

Satel

Satel SD-3001 Bedienungsanleitung

Satel

Satel Micra MPB-300 Bedienungsanleitung

Satel

Satel SILVER Bedienungsanleitung

Satel

Satel ASP-105 Bedienungsanleitung

Satel

Satel SP-4002 Bedienungsanleitung

Satel

Satel SPW-250 Bedienungsanleitung

Satel

Satel SPL-5020 Bedienungsanleitung

Satel

Satel SP-6500 Bedienungsanleitung

Satel

Satel ABAX 2 Bedienungsanleitung

Satel

Satel ABAX 2 Bedienungsanleitung

Satel

Satel ROP-101/EU Bedienungsanleitung

Satel

Satel MSP-300 Bedienungsanleitung

Satel

Satel MSP-300 Bedienungsanleitung

Satel

Satel CA-64 E Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung