Satel SPW-150 Bedienungsanleitung

SPW-150

INDOOR SIREN

spw150_en 07/17

The SPW-150 indoor siren is designed for operation in the intruder alarm systems.

1. Features

Acoustic signaling by means of piezoelectric transducer.

Three selectable tones.

Tamper protection in 2 ways – cover removing and tearing enclosure from the wall.

Battery back-up power supply.

Alarm by main power failure.

Fig. 1. The siren inside with cover removed.

Explanations for Fig. 1:

1 - battery.

2 - mounting holes.

2 SPW-150 SATEL

3 - piezoelectric transducer.

4 - cable entry holes.

5 - electronics board (Fig. 2).

2. Description of Electronics Board

Fig. 2. View of electronics board and selection of signaling control method.

Explanations for Fig. 2:

1 - battery wires.

2 - terminals:

+12V – power supply input.

COM – common ground.

D– control input.

TMP – tamper output (NC).

3 - tamper contact, which opens when the cover is removed.

4 - pins for selecting the way of sound signal triggering:

-D - by removing common ground (common ground control);

+D - by removing +12 V voltage (+12 V DC ±15% voltage control).

5 - wires to piezoelectric transducer.

6 - pins for tone selection.

7 - description of setting jumpers for respective tone.

3. Description of Operation

The indoor siren requires power supply from a 12 V ±15% DC voltage source. The acoustic

alarm will be triggered on loss of the control signal fed to the terminal D (depending on the

configuration: common ground or +12 V DC voltage) and continues until the signal is

restored. Additionally, the signaling will be set off if the cables are disconnected (external

power supply is lost). In this case the alarm will continue until the battery is discharged or

external power supply is restored.

In case of the alarm control panels manufactured by SATEL, it is recommended that the low-

current reversed polarity output be used for control (the jumper in siren set to –D position).

SATEL SPW-150 3

4. Installation and Hook-up

Fig. 3. Removing the cover.

The siren may only be used indoor.

The siren should be installed on a flat surface by means of wall plugs (screw anchors)

and screws.

Power down the control panel before connecting the siren to it.

Install the battery inside the siren only after all installation work is completed and the

alarm system power supply turned on. If the battery is installed before the external power

supply is turned on, alarm will be triggered.

Fig. 4. The way of connecting the siren to the alarm control panel. OUTx – control panel

output with power supply function. OUTy – control panel output for signaling control. Zx –

control panel zone programmed as 24h tamper.

Note: Reversed polarity must be programmed for SPW-150 siren control outputs in the

SATEL made control panels.

4 SPW-150 SATEL

5. Specifications

Supply voltage ................................................................................................... 12 V DC ±15%

Standby current consumption .......................................................................................... 10 µA

Maximum current consumption ......................................................................................330 mA

Sound pressure level (at 1 m distance)..................................................................up to 120 dB

Backup battery .............................................................................................. battery 6LR61 9 V

Standards complied with ......................................................................EN50130-4, EN50130-5

Environmental class according to EN50130-5 .........................................................................II

Operating temperature range.................................................................................. -10…+55°C

Maximum humidity ..........................................................................................................93±3%

Dimension x 40 mm

eight...............................................................................................................................162 g

s................................................................................................. 130 x 130

The declaration of conformity may be consulted at www.satel.eu/ce

Always use the 6LR61 9 V batteries. The battery is not included with the siren

and must be purchased separately.

Service representative should periodically check the battery status within the

scope of maintenance work.

Be particularly careful when replacing the battery. If inappropriately done,

replacement of the battery may lead to a risk of explosion. The Manufacturer

bears no responsibility for any consequences of incorrect replacement of the

battery.

The used batteries must not be discarded, but should be disposed of in

accordance with the existing rules for environment protection.

SATEL sp. z o.o. • ul. Budowlanych 66 • 80-298 Gdańsk • POLAND

tel. + 48 58 320 94 00

www.satel.eu

Inhaltsverzeichnis

Andere Satel Sicherheitssystem Handbücher

Satel

Satel CA-64 E Bedienungsanleitung

Satel

Satel ASP-100-R Bedienungsanleitung

Satel

Satel SPL-2030 Bedienungsanleitung

Satel

Satel CA-4M Bedienungs- und Wartungsanleitung

Satel

Satel APD-200 Bedienungsanleitung

Satel

Satel ASP-201 Bedienungsanleitung

Satel

Satel SP-500 Bedienungsanleitung

Satel

Satel SP-4003 R Bedienungsanleitung

Satel

Satel SPL-5010 Bedienungsanleitung

Satel

Satel ASP-105 Bedienungsanleitung

Satel

Satel SPL-5010 Bedienungsanleitung

Satel

Satel SPL-5020 Bedienungsanleitung

Satel

Satel MICRA Bedienungsanleitung

Satel

Satel Micra MPB-300 Bedienungsanleitung

Satel

Satel ASP-105 Technisches Handbuch

Satel

Satel SPL-2010 Bedienungsanleitung

Satel

Satel INT-TSG Betriebsanleitung

Satel

Satel SPL-2010 Bedienungsanleitung

Satel

Satel ASP-200 Bedienungsanleitung

Satel

Satel MSP-300 Bedienungsanleitung

Satel

Satel ROP-101/EU Bedienungsanleitung

Satel

Satel CA-64 E Bedienungsanleitung

Satel

Satel ABAX 2 ASP-200 Bedienungsanleitung

Satel

Satel SP-4004 Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung

DSC

DSC PC 4010 Betriebsanleitung

UniPOS

UniPOS 6202L Bedienungsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Rondish

Rondish Nexus Bedienungsanleitung