Satel SPL-2010 Bedienungsanleitung

Optical-acoustic siren

SPL-2010

spl2010_en 07/23

SATEL sp. z o.o. •ul. Budowlanych 66 • 80-298 Gdańsk • POLAND

tel. +48 58 320 94 00

www.satel.pl

IMPORTANT

The device should be installed by qualified personnel.

Prior to installation, please read carefully this manual.

Changes, modifications or repairs not authorized by the manufacturer shall void your rights

under the warranty.

SATEL aims to continually improve the quality of its products, which may result in changes in

their technical specifications and software. Current information about the changes being

introduced is available on our website.

Please visit us at:

https://support.satel.pl

The declaration of conformity may be consulted at www.satel.pl/ce

The following symbols may be used in this manual:

- note;

- caution.

CONTENTS

1. Features............................................................................................................................2

2. Description ........................................................................................................................2

Terminals..........................................................................................................................3

Pins for selecting acoustic signal......................................................................................3

Enclosure base.................................................................................................................3

3. Installation and start-up.....................................................................................................4

4. Specifications....................................................................................................................5

2 SPL-2010 SATEL

The SPL-2010 siren provides information about alarm situations by means of optical and

acoustic signaling. It is designed for outdoor installation. This manual applies to the siren with

electronics version 1.7.

1. Features

•Acoustic signaling by means of sounder.

•Three selectable tones for acoustic signaling.

•Optical signaling by means of LEDs.

•Weatherproofed electronic circuit.

•Tamper protection against enclosure opening, removing from mounting surface and

flooding of the sounder with mounting foam.

•Inner cover of galvanized metal sheet.

•High-impact polycarbonate enclosure, featuring a very high mechanical strength.

2. Description

enclosure cover.

inner metal cover.

enclosure base.

sounder.

anti-foam detector.

electronics board.

cover locking screw.

SATEL SPL-2010 3

Terminals

+SO- - input to trigger the optical signaling. The signaling will be triggered after +12 VDC

voltage is applied to terminal “+” and 0 V voltage (common ground) is applied to

terminal “-”.

+SA- - input to trigger the acoustic signaling. The signaling will be triggered after

+12 VDC voltage is applied to terminal “+” and 0 V voltage (common ground) is

applied to terminal “-”.

TMP - tamper output (NC). Connect one terminal to the control panel zone programmed

as tamper, and the other to the control panel common ground.

Pins for selecting acoustic signal

Fig. 2 shows the jumpers settings for each selectable siren tone: A–tone 1, B–tone 2, C–

tone 3.

Enclosure base

mounting holes.

anti-foam detector.

sounder.

opening for wires.

4 SPL-2010 SATEL

electronics board.

tamper element with mounting hole.

water drain holes (do not plug).

3. Installation and start-up

Power down the control panel before connecting the siren to the control panel.

The siren must be installed on the wall, high above the floor, at a hard to access location, so

as to minimize the risk of tampering. Leave a space above the siren –at least 4.5 cm

between the siren and the ceiling or other object. Otherwise, it will be impossible to replace

the cover.

1. Remove the cover locking screw.

2. Lift up the enclosure cover and remove it (Fig. 4).

3. Pull aside the mounting catches of the inner metal cover and remove it.

4. Place the enclosure base on the wall and mark the location of mounting holes (Fig. 3).

Remember to take into account the mounting hole for tamper protection.

5. Drill the holes for wall plugs (anchors).

6. Run the wires through the opening in the enclosure base (Fig. 3).

7. Use wall plugs (anchors) and screws to secure the enclosure base to the wall. Remember

about the mounting hole for tamper protection. Select appropriate wall plugs based on the

type of the mounting surface (different for concrete or brick wall, different for plaster wall,

etc.).

8. Connect the siren terminals to the control panel terminals using wires.

Some alarm control panels may require that a resistor R (approx. 1 kΩ) be connected

between the +SA- terminals in the siren (Fig. 3). Otherwise, the siren may produce

a buzzing sound when inactive (if there is no buzzing, the resistor is not required).

9. Use jumpers to select the tone (Fig. 2).

10.Replace the inner metal cover.

11.Replace the siren cover and lock it with the screw.

12.Power on the control panel.

SATEL SPL-2010 5

After the siren is mounted, it is recommended to seal the mounting holes and cable

entry hole with silicone paste.

4. Specifications

Supply voltage.................................................................................................... 12 VDC

15%

Maximum current consumption:

optical signaling...........................................................................................................35 mA

acoustic signaling......................................................................................................250 mA

optical and acoustic signaling....................................................................................300 mA

Sound pressure level (at 1 m distance) .................................................................up to 120 dB

Environmental class according to EN 50130-5.......................................................................III

6 SPL-2010 SATEL

Operating temperature range...............................................................................-35°C...+55°C

Maximum humidity..........................................................................................................93

Dimensions................................................................................................. 298 x 197 x 90 mm

Weight............................................................................................................................1,22 kg

Inhaltsverzeichnis

Andere Satel Sicherheitssystem Handbücher

Satel

Satel SP-4003 R Bedienungsanleitung

Satel

Satel ABAX 2 Bedienungsanleitung

Satel

Satel SP-4001 Bedienungsanleitung

Satel

Satel CA-64 E Bedienungsanleitung

Satel

Satel MSP-300 Bedienungsanleitung

Satel

Satel ASP-105 Bedienungsanleitung

Satel

Satel ASP-100-R Bedienungsanleitung

Satel

Satel WZ-100 Bedienungsanleitung

Satel

Satel SPL-5010 Bedienungsanleitung

Satel

Satel MICRA Bedienungsanleitung

Satel

Satel CA-64 E Bedienungsanleitung

Satel

Satel SPW-100 Bedienungsanleitung

Satel

Satel ASP-105 Bedienungsanleitung

Satel

Satel SPL-2030-R Bedienungsanleitung

Satel

Satel SP-500 Bedienungsanleitung

Satel

Satel ABAX 2 Bedienungsanleitung

Satel

Satel ASP-200 Bedienungsanleitung

Satel

Satel ASP-205 Bedienungsanleitung

Satel

Satel SPL-2010 Bedienungsanleitung

Satel

Satel SP-4004 Bedienungsanleitung

Satel

Satel SP-4002 Bedienungsanleitung

Satel

Satel ASP-100 Bedienungsanleitung

Satel

Satel SD-3001 Bedienungsanleitung

Satel

Satel SOW-300 Series Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung