Schwinn SC7 Bedienungsanleitung

Assembly Instructions

Page 1

620-8607 Rev. A

SC5 + SC7 + SC Power Install Sheet

Applies to: SC5 (9-7410) + SC7 (9-7400) + SC Power (9-7380)

SC5 ASSEMBLY INSTRUCTIONS

STEP 1: Install the front stabilizer using two (2) pieces each of the

M10 x 25mm hex head screws, M10 split lock washers, and M10

washers. Repeat this step to attach the rear stabilizer.

STEP 2: Install the seat post by loosening the height adjustment

pop pin, then pulling outwards on the pin while sliding the seat

post into the frame.

STEP 3: Pull down on the seat slider locking pin then slide the

seat assembly onto the seat post installed in Step 2, tightening

the fore/aft adjustment knob to lock the seat slider into place.

NOTE: The fore/aft adjustment knob may need to be loosened.

STEP 4: Insert one (1) piece of the trapezoidal locking nut into

the handlebar post then slide the handlebar onto the handlebar

post. Next, insert one (1) piece of the threaded collar locking nut

through the handlebar and into the trapezoidal locking nut, tight-

ening with a 10mm allen key. Slide one (1) M8 washer onto the

fore/aft adjustment knob then tighten the knob into the threaded

collar locking nut. Finally, secure the end cap onto the handlebar

post using one (1) piece of the M4 x 10mm screw.

Fore/Aft

Adjustment

Knob

M8 Washer

Threaded Collar

Locking Nut

Trapezoidal

Locking Nut

Assembly Instructions

Page 2

620-8607 Rev. A

SC5 ASSEMBLY INSTRUCTIONS CONT.

STEP 5: Install the user right side pedal into the crank arm then

use a torque wrench and a 8mm allen socket to secure one (1)

piece of the crank bolt from the other side of the pedal, torquing

to 33-37 ft-lbs (45-50 Nm). Repeat this step for the rider left side

pedal.

NOTE: The pedal MUST be torqued to the above specications

otherwise a failure of the pedal may occur.

Assembly Instructions

Page 3

620-8607 Rev. A

SC7 ASSEMBLY INSTRUCTIONS

STEP 1: Slide the threaded stabilizer plate into the bike frame

then use a 13mm socket to secure the rear stabilizer onto the

frame using two (2) pieces of the M8 x 30mm bolts and M8 wash-

ers. Repeat this step for the front stabilizer.

STEP 2: Insert one (1) piece of the trapezoidal fore/aft locking

nut into the handlebar post then slide the handlebars onto

the handlebar post. Secure one (1) piece of the threaded collar

locking nut through the handlebars and into the trapezoidal fore/

aft locking nut using a 10mm allen key. Next, slide one (1) piece

of the M8 washer onto the fore/aft adjustment knob then tighten

the fore/aft adjustment knob into the threaded collar locking nut.

STEP 3: Slide the seat post into the frame by loosening the height

adjustment pop pin, then pulling outwards on the pin while

sliding the seat into the frame.

STEP 4: Pull down on the seat slider locking pin then slide the

seat assembly onto the seat post installed in Step 3, tightening

the fore/aft adjustment knob to lock the seat slider into place.

Fore/Aft

Adjustment

Knob

M8 Washer

Threaded Collar

Locking Nut

Trapezoidal

Locking Nut

Threaded

Stabilizer

Plate

Assembly Instructions

Page 4

620-8607 Rev. A

SC7 ASSEMBLY INSTRUCTIONS CONT.

STEP 6: Install the pedal into the crank arm then use a torque

wrench and a 8mm allen socket to secure one (1) piece of the

crank bolt from the other side of the pedal, torquing to 33-37 ft-

lbs (45-50 Nm). Repeat this step for the rider left side pedal.

NOTE: The pedal MUST be torqued to the above specications

otherwise a failure of the pedal may occur.

Assembly Instructions

Page 5

620-8607 Rev. A

SC POWER ASSEMBLY INSTRUCTIONS

STEP 1: Slide the threaded stabilizer plate into the bike frame

then use a 13mm socket to secure the rear stabilizer onto the

frame using two (2) pieces of the M8 x 30mm bolts and M8 wash-

ers. Repeat this step for the front stabilizer.

STEP 2: Insert one (1) piece of the trapezoidal fore/aft locking

nut into the handlebar post then slide the handlebars onto

the handlebar post. Secure one (1) piece of the threaded collar

locking nut through the handlebars and into the trapezoidal fore/

aft locking nut using a 10mm allen key. Next, slide one (1) piece

of the M8 washer onto the fore/aft adjustment knob then tighten

the fore/aft adjustment knob into the threaded collar locking nut.

STEP 3: Slide the seat post into the frame by loosening the height

adjustment pop pin, then pulling outwards on the pin while

sliding the seat into the frame.

STEP 4: Pull down on the seat slider locking pin then slide the

seat assembly onto the seat post installed in Step 3, tightening

the fore/aft adjustment knob to lock the seat slider into place.

Fore/Aft

Adjustment

Knob

M8 Washer

Threaded Collar

Locking Nut

Trapezoidal

Locking Nut

Threaded

Stabilizer

Plate

Assembly Instructions

Page 6

620-8607 Rev. A

SC POWER ASSEMBLY INSTRUCTIONS CONT.

STEP 6: Install the pedal into the crank arm then use a torque

wrench and a 8mm allen socket to secure one (1) piece of the

crank bolt from the other side of the pedal, torquing to 33-37 ft-

lbs (45-50 Nm). Repeat this step for the rider left side pedal.

NOTE: The pedal MUST be torqued to the above specications

otherwise a failure of the pedal may occur.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Schwinn Heimtrainer Handbücher

Schwinn

Schwinn SR23 Bedienungsanleitung

Schwinn

Schwinn A.C. Performance Bedienungsanleitung

Schwinn

Schwinn 570U Bedienungsanleitung

Schwinn

Schwinn 102 Bike Bedienungsanleitung

Schwinn

Schwinn NAUTILUS 113 Bedienungsanleitung

Schwinn

Schwinn Airdyne Bedienungsanleitung

Schwinn

Schwinn 120 Bedienungsanleitung

Schwinn

Schwinn 9-7300 A.C. Power Bedienungsanleitung

Schwinn

Schwinn 270 Recumbent Bike Bedienungsanleitung

Schwinn

Schwinn a25 Bedienungsanleitung

Schwinn

Schwinn NAUTILUS A10 Bedienungsanleitung

Schwinn

Schwinn 250 Bedienungsanleitung

Schwinn

Schwinn Airdyne Bedienungsanleitung

Schwinn

Schwinn Airdyne Evolution Comp Bedienungsanleitung

Schwinn

Schwinn 120 Bedienungsanleitung

Schwinn

Schwinn 250 Bedienungsanleitung

Schwinn

Schwinn Airdyne Bedienungsanleitung

Schwinn

Schwinn AD6 Bedienungsanleitung

Schwinn

Schwinn EVO Airdyne Bedienungsanleitung

Schwinn

Schwinn 206 Recumbent Bike Bedienungsanleitung

Schwinn

Schwinn Schwinn A.C. Classic Bedienungsanleitung

Schwinn

Schwinn 103/203 Bedienungsanleitung

Schwinn

Schwinn IC PRO Bike Betriebsanleitung

Schwinn

Schwinn active 10 Series Bedienungsanleitung

Beliebte Heimtrainer Handbücher anderer Marken

TOORX

TOORX BRX85 Bedienungsanleitung

Matrix

Matrix KranKcycle Bedienungsanleitung

Weslo

Weslo Vector 302 Kurzanleitung

Matrix

Matrix IC3 Bedienungsanleitung

Sunny Health & Fitness

Sunny Health & Fitness SF-B121021 Bedienungsanleitung

Monark

Monark 827E Bedienungsanleitung

Stamina

Stamina 1310 Bedienungsanleitung

American Fitness

American Fitness SPR-BK1072A Bedienungsanleitung

Cateye

Cateye CS-1000 (CYCLO SIMULATOR) Bedienungsanleitung

BH FITNESS

BH FITNESS H9158H Bedienerhandbuch

Body Sculpture

Body Sculpture BC-7220G Bedienungsanleitung

Cateye

Cateye EC-2300 Bedienungsanleitung

FYTTER

FYTTER RACER RC MSR Bedienungsanleitung

Kikos

Kikos HM-9090M Bedienungsanleitung

Fuel Fitness

Fuel Fitness SU135-40 Bedienungsanleitung

NordicTrack

NordicTrack Gxr 4.2 Bike Bedienungsanleitung

Vision Fitness

Vision Fitness U70 Bedienungsanleitung

Stamina

Stamina 15-0340A Bedienungsanleitung