SDC S6200 Series Bedienungsanleitung
INSTALLATION INSTRUCTIONS
801 Avenida Acaso, Camarillo, Ca. 93012
• (805) 494-0622 • www.sdcsecurity.com
E-mail: service@sdcsecurity.com
S6200 SERIES
PANIC/FIRE EXIT
SURFACE MOUNTED
VERTICAL ROD DEVICES
These instructions are presented
in a step by step sequence.
Please read it through before
installation.
Note: The dimensions are shown
in inches. See attached page for
the Metric Conversion Table for
millimeters.
P:\INSTALLATION INST\Mechanical Hardware\INST-S6200.vsd Rev - 01/11 Page 1
P:\INSTALLATION INST\Mechanical Hardware\INST-S6200.vsd Rev - 01/11 Page 2
DESIGNATION OF PARTS
Top Strike Fixing Plate
Top Strike
(Back View)
Top Latch
Assembly
Top Rod
Shaft Connector
Bottom Strike
Base
Bottom Strike
(Fire Label)
End Cap
End Cap Bracket
Mechanism
Housing
Dogging Device Fire Exit
Hardware is not equipped
with this device
Push Bar
Bottom Strike
(Panic Label)
Chassis
Cover
CAUTION:
Before installing
this device, check
contents of box
for size of device,
function, finish
color and outside
trim to be used.
Top Strike
(Panic Label)
Top Strike
(Fire Label)
Bottom Latch
Assembly Cover
Top Latch
Assembly Cover
Mounting
Bracket
Chassis
Assy.
Rod Guide
Mounting
Bracket
Bottom Latch
Assembly
Bottom Rod
Rod Guide
P:\INSTALLATION INST\Mechanical Hardware\INST-S6200.vsd Rev - 01-11 Page 3
STEP 1: PREPARE DOOR
1. Mark position of holes on the door per template (see figure 1).
2. Drill all holes marked on the door for the device chassis and top and bottom latch mounting
brackets.
3. Mortise hole for outside trim is required.
NOTE; Any hole drilled from the outside, first needs a pilot hole drilled from the inside
to ensure good alignment.
Figure 1
2-7/16”
Mark Backset
JAMB
2-5/16" 3-7/32"
INSIDE FACE OF DOOR
1016mm
(40")
Mark of device
C
L
3-7/32"
1-15/32"
1/4”
of top and bottom latches
C
L
Surface of the door must be
flush. Clear away any raised
jutting to allow the exit device to
rest on flat surface of the door.
40" to finished floor
Standard centerline height of device is 40" above the finished floor.
Prepare door for your specific
device per supplied template.
STEP 2: INSTALL BRACKETS, DEVICE & TRIM
1. Remove chassis cover from chassis assembly and end cap from end cap bracket.
2. Cut the length if required.
For user information; This model device has three different lengths:
For use on 3' wide door, device = 33"
For use on 3.5' wide door, device = 40"
For use on 4' wide door, device = 44"
a. The device length is pre-cut for use on 36", 42" or 48" wide doors, no additional
cutting is necessary. If narrow door installation is required, cut device at section “A”
to door width minus 2" for proper fit.
b. Remove device from door, remove end cap and end cap bracket and cut where required.
NOTE: Device must be cut flat with all burrs removed for end cap to fit properly.
3. Mount device horizontally via the drilled holes and secure with supplied
mounting hardware. Attach device to trim or sexbolt.
4. Check that the trim actuator shaft fully inserts into the
device cam (refer to view “B”).
5. Install end cap bracket to device, level device
and mark then drill the mounting
holes. Attach to door with hardware
supplied. Attach end cap.
6. Install mounting brackets to top
and bottom of door.
P:\INSTALLATION INST\Mechanical Hardware\INST-S6200.vsd Rev - 01-11 Page 4
“A”
Hinge Stile edge of door
Mark mounting
holes thru end
cap bracket after
device is leveled.
Mounting
Bracket
Chassis
End cap
bracket
Figure 2
VIEW “B”
Insert Trim Actuator Shaft
Into Device Cam
*
*
P:\INSTALLATION INST\Mechanical Hardware\INST-S6200.vsd Rev - 01-11 Page 5
STEP 3: INSTALL BOTTOM ROD AND BOTTOM STRIKE
1. Mount the bottom latch assembly into the mounting bracket (see figure 3).
2. Screw the threaded end of the bottom rod onto the bottom latch assembly (see figure 4).
3. Using screw supplied, attach and tighten the bottom rod to the chassis at the location
indicated by the arrow in figure 5.
NOTE: If the hole on the bottom shaft connector does not align with the mounting hole in
the chassis, adjust the length by turning the rod in or out of the latch assembly.
4. Install bottom strike into finished floor or threshold, and be sure to align center line of bottom
latch with the centerline of the bottom strike (see figure 6)
5. Depress and release push bar to confirm proper installation.
5-1 Make sure bottom latch can be retracted and flush with
the edge of the door when push bar is depressed.
5-2 Check bottom latch bolt has 19/32" (15mm) throw min.
when push bar is released.
Figure 3 Figure 4
Threaded end of
Bottom rod
Figure 6
1/4”
2-1/4”
7/8”
2-3/32”
L
C
Figure 5
P:\INSTALLATION INST\Mechanical Hardware\INST-S6200.vsd Rev - 01-11 Page 6
STEP 4: INSTALL TOP ROD AND TOP STRIKE
1. Mount the top latch assembly into the mounting bracket (see figure 7).
2. Screw the threaded end of the top rod onto the top latch assembly completely (see figure 8).
Threaded end
of top rod
Figure 7
Figure 8
3. Measure and cut the length of the top rod. The length of the top rod is measured to the edge of
the rod connector (see figure 9) which will be attached to the chassis.
4. Insert the rod connector into the non-threaded end of the top rod and secure in place by
tightening the locking screw (see figure 10).
5. With the top rod connector installed, attach the top rod to the chassis at the location indicated
by the arrow (see figure 11).
Edge of rod
connector
Mark cutting line
and cut top rod
Figure 9
Non-threaded
end of top rod
Locking
screw
Figure 10 Figure 11
P:\INSTALLATION INST\Mechanical Hardware\INST-S6200.vsd Rev - 01-11 Page 7
6. Mark and drill mounting holes on the jamb for the top strike per the strike template (see figure 12).
Fasten the top strike to the jamb with the screws supplied (see figure 13).
STEP 5: TEST OPERATION
1. Depress the push bar. The top and bottom latches should be held retracted. The bottom latch
should also clear the floor and the bottom strike. Door can now be opened.
2. Release push bar, both the top latch bolt and the bottom latch bolt should be fully extended.
3. Check device operation by depressing and releasing push bar several times to assure final
installation is correct.
4. Repeat device operation by opening and closing door several times using the
outside trim to make sure all installations have no problems.
5. Repeat adjustment procedure if either the top latch bolt is not held
retracted, or bottom latch bolt does not clear floor and bottom strike.
STEP 6: INSTALL COVERS
1. Before installing covers, check and secure top and bottom latch
bolts engagement. Adjust strikes if necessary.
2. Install the chassis and top & bottom assembly covers and the
two rod guides (see figure 14).
Figure 13
Figure 14
Figure 12
NOTE:
Attach third screw last after strike
has been properly aligned,
Door Handing
Use this diagram to determine the hand of door.
NOTE:
To extend the life of this device,
it is recommended to activate
the dogging feature during high
traffic periods of the day.
Depress
Push Bar
Depress
Push Bar
Dogging:
Insert dogging wrench and
turn clockwise 15 degrees.
The push bar will remain
pressed and the latches
will remain retracted.
Release Dogging:
Insert dogging wrench and
turn counter-clockwise 15 degrees.
The push bar will return to the
up position and the latches will
extend to lock the door.
Dogging Wrench
Outside of Door
Inside of Door
RHR LHR
P:\INSTALLATION INST\Mechanical Hardware\INST-S6200.vsd Rev - 01-11 Page 8
Inhaltsverzeichnis
Andere SDC Türschloss Handbücher
SDC
SDC Z7836 Series Bedienungsanleitung
SDC
SDC 1190A Series Bedienungsanleitung
SDC
SDC E72 EntryCheck Bedienungsanleitung
SDC
SDC Z7200R Bedienungsanleitung
SDC
SDC FS23M Series Bedienungsanleitung
SDC
SDC PRO Series Bedienungsanleitung
SDC
SDC E75 Series Bedienungsanleitung
SDC
SDC ZY7500 Series Bedienungsanleitung
SDC
SDC Z7600 Series Bedienungsanleitung
SDC
SDC 1511S Bedienungsanleitung
SDC
SDC 1511S Bedienungsanleitung
SDC
SDC 180 Series Bedienungsanleitung
SDC
SDC 45 Series Bedienungsanleitung
SDC
SDC E75 Series Bedienungsanleitung
SDC
SDC E72K-A CIVIC SERIES Installationshandbuch
SDC
SDC Z7800 Series Bedienungsanleitung
SDC
SDC TEMPLATE 180 SERIES Bedienungsanleitung
SDC
SDC S6800 Series Kurzanleitung
SDC
SDC Z7870 Bedienungsanleitung
SDC
SDC PD2090A Bedienungsanleitung
