Seaga CA18 Bedienungsanleitung

CA18

18 Column

Mechanical Snack Vendor

Operator’s Manual

Seaga Manufacturing, Inc.

700 Seaga Drive

Freeport, IL USA 61032

www.seaga.com

INTRODUCTION

Congratulations on the purchase of your new vending machine. This vendor has been designed to give

you many years of dependable service. It requires little maintenance and is easy to set up and oper-

ate.

READ THIS MANUAL COMPLETELY

Your vendor is designed to operate simply and reliably, but to take full advantage of your machine,

please read this owner's manual thoroughly. It contains important information regarding installation

and operations, as well as a brief trouble-shooting guide.

EQUIPMENT INSPECTION

After you have received your machine and have it out of the box, place it on a secure surface for fur-

ther inspection. Note: Any damages that may have occurred during shipping must be reported to the

delivery carrier immediately. Reporting damages and the seeking of restitution is the responsibility of

the equipment owner. The factory is willing to assist you in this process in any way possible. Feel free

to contact our Customer Care Department with questions you may have on this process.

It is important that you keep the original packaging for your vending machine at least through the war-

ranty period. If your machine needs to be returned for repair, you may have to purchase this packag-

ing if it is not retained.

Once you have your vendor located, we suggest that you keep this manual for future reference.

Should any problems occur, refer to the section entitled "COMMON QUESTIONS AND ANSWERS".

It is designed to help you quickly identify a problem and correct it.

700 Seaga Drive

Freeport, IL 61032 U.S.A.

815.297.9500

seaga.com

18 Column

Mechanical

Snack Vendor

Mechanism

Panels

Lock

Front Door

Coin Mechanism

Knob

Product

Window

Vend Area

Coin Box

Mechanism Panel

and Product Tray

LOCKS

Your CA18 Vendor has one (1) screw type Lock. To unlock the Front Door, unscrew the Lock counter clockwise until the door is

free. To lock, apply firm pressure below the Lock as you tighten the Lock. Do not over tighten as you could ruin the seal. You will

be able to remove the key, only when the key is vertical or horizontal.

MOUNTING (optional)

Your CA18 offers you many flexible options within your vending environment. The CA18 allows the versatility of a stand alone

countertop vendor, mounting to the optional stand (Fig. 1), additionally, it may be mounted to Seaga’s BV155 (5 select) soda ven-

dor which allows for optimum use of floor space within the vending environment. Mounting to the BV155 offers your customers

the variety of cold beverages along with their snack purchase.

1. To assemble the CTS stand.

A.) Attach Legs to short, side supports as shown in Fig. 1, by inserting bolts

through Legs, and then attaching support to inside of Leg with nuts.

B.) Once both ends are assembled attach Front/Rear Supports in same

manner, one end at a time.

C.) CA18 sits atop stand and is held in place by the Rear Legs.

Note: The CA18 rests on the SMS stand, attaching the stand permanently to the CA18 is at the owner's discretion.

Your CA18 can be mounted to the BV155 to form the Mechanical Combination Vendor.

The vendor comes with mounting hardware. You will need tools for mounting.

1. To Mount the CA18 to the BV155.

A.) Set the CA18 on top of BV155.

B.) Unlock and open the Front Door of the CA18. The BV155 does not need to be opened.

(The following is to be done within the CA18.)

C.) Remove bottom Product Tray. Pull Product Tray fully forward, and out.

D.) Attach the CA18 to the top of the BV155. Insert the two (2) Phillips head screws found in the BV155 parts pack

down through the CA18 into the threaded holes in the top of the BV155.

E.) Reassemble.

Figure 1 Optional Stand Assembly

Side Supports

Front/Rear

Supports

Front Legs

Small arrows

indicate direction

for inserting bolts

Leg detail

Note:

Front Legs

are folded

over on

both ends.

Rear Leg

Figure 2 Optional Soda Vendor Mount

BV155 Vendor Mounting

holes

Snack Vendor

Vend Area

Phillips mounting

screws

Product Tray

(Remove)

DELIVERY SYSTEM

Your new CA18 features a rear-drop delivery system to prevent theft. The CA18 delivery system is made up of three (3) com-

ponents, the Product Tray, the Helix Coils, and the Coin Mechanism (Fig. 3). Once the proper amount of coins is received the

Coin Mechanism drives the Helix Coil and pushes the product out the back of the Product Tray.

DRIVER MECHANISM

The Mechanism Panel is the front panel. This panel controls the receiving of money and the action of the Helix Coil. Once the

correct amount of money is received, the Mechanism Knob can be turned clockwise. Product is vended by turning the Mechanism

Knob one (1) complete revolution.

The Driver Mechanism (Fig. 4) comes factory preset but can be changed to suit your needs. The Coin Sub-Assembly is made

up of a series of discs consisting of white, black and metal Coin Discs. The white spacers are thinner than the black, and the

combination of the two place the Coin Discs in the proper position to receive coins.

In some cases you will find all one (1) color of spacers. This is common in an

all-quarter configuration. Contact our Customer Care Dept. for additional instructions on changing your Coin Sub-Assembly if

necessary.

1.To access Coin Mechanism:

A.) Unlock and remove Front Door.

B.) Remove the Mechanism Panel by first removing the two (2) Silver Screws on both sides of the Mechanism Panel.

C.) Pull the Mechanism Panel outward. Carefully free Drivers from all Helix Coils.

D.) Turn desired Mechanism Knob clockwise ¼" turn and place Mechanism Panel face down on a flat surface,

exposing the Driver Mechanism and "S" bracket assembly. (Fig. 7)

Note: Change one Driver Mechanism at a time.

E.) To change Driver Mechanisms, remove two (2) nuts (Fig. 5) and gently remove "S" Bracket Assembly.

F.) Unscrew and remove the two (2) Screws holding Driver to the Coin Sub-Assembly. (Fig. 5 & Fig. 6 )

Figure 3 Delivery System

Driver

Mechanism

Helix Coil

Product Tray

Figure 4 Driver Mechanism reference

From Knob to Driver is

the “Driver Mechanism”

All discs are the

“Coin Sub-Assembly”

G.) Coin Sub-Assembly (Fig. 4 & Fig. 6 ) will come apart from Knob and can be carefully removed.

2. To assemble Driver Mechanism:

A.) Lubricate backside of Mechanism Panel around holes with a small amount of petroleum jelly.

B.) Insert two (2) screws through Coin Sub-Assembly to Knob. Make sure Knob is seated properly and tighten screws

into place. If handle is hard to turn, loosen the two (2) screws 1/8to ¼ turn.

C.) Turn mechanism Knob to align Coin Discs with "S" bracket mounting studs. Install "S" bracket assembly over

mounting studs. Do not install the nuts yet.

D.) Now turn Mechanism Knob so Coin Disc slots are facing down. The Anti-Reverse Dog can now be raised enough

to enable the Anti-Reverse Dog Spring to seat under the Anti-Reverse Dog. At the same time the "S" bracket

assembly will be seated against Mechanism Panel. Place Keps Nut on upper mounting stud. (DO NOT TIGHTEN

NUTS.) (Fig. 4 and Fig. 6)

E.) Turn Knob to align coin discs with "S" bracket assembly, once again. Use a screwdriver to push top of "S" bracket

assembly fully to right and tighten Keps Nut. You may now tighten Nylon Threaded Nut to lower mounting stud

(DO NOT OVER TIGHTEN).

Note: The fingers of the Coin Rejecter must align with Coin Discs of the Coin Sub-Assembly. The Coin Discs strike the center

of each finger to prevent vending without coins. This alignment is critical. If the fingers are misaligned the vendor will not

vend. (Fig 8)

F.) Check to see that "S" bracket assembly is firmly seated against Mechanism Panel and upper mounting stud. Check

that Anti-Reverse Dog Spring is engaged on Anti-Reverse Dog. Make sure Anti-Reverse Dog moves freely and locks into

Ratchet Disc as the mechanism is rotated counter-clockwise. If Anti-Reverse Dog does not move freely, loosen Nylon

Threaded Nut on the lower mounting stud. If this does not help, remove "S" bracket assembly and close Anti-Reverse Dog

Spring to put more pressure on Anti-Reverse Dog. Check that coin discs are properly aligned with the Coin Rejecter by insert-

ing money through slots in the top of the Mechanism Panel. Make sure the Coin Rejecter is properly engaging the coin disc

stops. (Improper alignment will allow coins to slip between slots in the Coin Rejecter.)

Refer to the optional mechanism configurations at the end of this manual. Always make sure your Driver Mechanism is built as

specified in the diagram. Note: The disc next to the Driver is always placed upside down (the rounded side will be at the top of

Figure 6 Driver Mechanism exploded view - Standard $1.00 Configuration

Figure 5 Inside view of Driver Mechanism

“S” Bracket

Assembly

Coin

Deflector

Driver Mechanism

Driver

Screws

Knob

PL104 Mechanism

Panel

Ratchet Disc

ST103

Quarter Disc

ST105

White Spacer

ST108

Driver

ST340

Screws

ST112

Black Spacer

ST104

the disc only) to prevent coins from jamming the mechanism.

LOADING PRODUCT

To present your product in as an attractive and professional manner as possible, do not load any damaged items, and make

sure items are facing forward for easy

identification by your customer.

Note: The size of the item being vended must be larger than the Helix Coil, but smaller than the Column, to vend correctly.

Never force an oversized item into the Helix Coil or Column, nor attempt to vend an item that is smaller than the Helix Coil as

this will create problems and deter customers.

1. To Load Product:

A.) Pull Product Tray forward.

B.) Place product in proper size Helix Coil. Note: Bottom of product must rest on the Product Tray and not on the Helix

Coil. (Fig.9) Load each Helix Coil from back to front. Note: Fill all Helix Coils fully, do not leave any empty spaces

behind or between items. If you must leave empty space leave it in the front of the Tray closest to the Product

Window.

C.) Once Product Tray is fully loaded, lift and push it back in.

Special Note: We suggest that you always partially fill the vendor with product and perform at least five (5) test vends.

Figure 7 “S” Bracket Assembly Keps Nut

SS206

Nylon

Threaded

Nut

SS207

“S” Bracket

ST201

Anti-Reverse

Dog

PL204

Anti-Reverse

Dog Spring

ST203

Screws (2)

SS914

Coin Rejecter

ST202

Figure 8b Vend!

Accepted coins push the

fingers over the Coin

Discs’ catches to vend.

Figure 8 Proper Finger Alignment

Figure 8a Accepted!

Coins should push the fingers out.

Make sure coins contact the

center of the fingers.

COIN RETRIEVAL

One (1) Coin Box is provided with your CA18. They are stored below the Product Tray directly behind and below the Coin

Mechanisms. Once the Front Door is open, pull out the product tray and then pull the Coin Box out to the right to empty it.

GENERAL NOTES

It is suggested that a tool box accompany you to each of your locations. Suggested items for this tool box would include a sock-

et set, (up to a 1/2" socket size suggested) a Phillips and a Standard screwdriver. Additional items would be a small jar of

Petroleum Jelly (Vaseline), a small brush for applying the Petroleum Jelly, a soft rag and perhaps a Black Magic marker. The

magic marker is useful in touching up light scratches that may occur to your vendor.

COMMON QUESTIONS AND ANSWERS

MAINTENANCE

Q: My knob turns without coins.

A: Your Coin Rejecter is loose, misaligned or broken. Refer to the Driver

Mechanism section of this manual for proper placement of

the Coin Rejecter. (See Fig. 7 & Fig. 10)

Q: My mechanism screws keep coming loose.

A: Remove Mechanism Panel. Disassemble Knob. Apply lock tight to Knob

screw threads. If this does not remedy the problem a replacement

Knob may be needed.

Q: My mechanism rotates backward.

A: Your Knob should not do this. Remove the Mechanism Panel and check for

proper placement and condition of the Anti-Reverse Dog.

Q: My mechanism rotates but product will not drop.

A: Check to see if the product is jammed in the Column.

Check to see if the vendor is level.

Check product for damage, and make sure it is the proper size.

Q: My knob turns ¼" turn and jams.

A: First remove your Mechanism Panel. Check the position of the coins to see if

they are in-between the Coin Rejecter fingers. If this is the case,

place a screwdriver in-between the Coin Rejecter and the discs and

lift up freeing the Coin Rejecter. At this point the Driver Mechanism

can now be rotated backwards. Reposition the Coin Rejecter fingers

with your screwdriver to line up with coins and vend through. (Fig.10)

Figure 9 Loading Product

Correct - load

product between

Helix Coils,

resting on the

product tray

Incorrect

Product Tray

Columns

Helix Coil

GENERAL

Q: Can customers reach up and help themselves to product?

A: No. The Vendor pushes product out the back of the Product Trays.

Q: My key won't turn my Lock to open.

A: Check to be sure that you are using the proper key. If the correct key is being

used, your Lock may have been damaged or vandalized. Vandalism

to locks is quite common. Having spare Locks in your toolbox at all

times is recommended.

Q: What can I use to clean the outside of my vendor?

A: A lint free rag and a mild window cleaner are recommended.

Be sure however not to directly spray decals as the ink could run.

Q: How do I remove a Lock that won’t open.

A: Drill into the center of the Lock with a 1/4” drill bit. The Lock should fall apart

and be easily removed. Increase the bit size and try again if the Lock

does not come out.

Figure 10 Coin Rejecter Fingers

Figure 10a Caught!

Empty Coin Discs should

catch on the center of the

Coin Rejector fingers.

Figure 10b Accepted!

Coins should push the

fingers out. Make sure

coins contact the center

of the fingers.

Figure 10c Vend!

Accepted coins push the

fingers over the Coin

Discs’ catches to vend.

Knob

PL104

Mechanism

Panel

Ratchet Disc

ST103

Quarter Disc

ST105

White Spacer

ST108

Driver

ST110

Screws

SS112

Black Spacer

ST104

Black Spacer

ST104

Standard

$.50 configuration

shown

Figure 11 Optional $.50 configuration

Figure 13 Optional $.65 configuration

Knob

PL104 Mechanism Panel

Ratchet Disc

ST103

Quarter Disc

ST105

White Spacer

ST108

Driver

ST110

Screws

SS112

Black Spacer

ST104

Dime Disc

ST107 Nickel Disc

ST107

Figure 12 Optional $.60 configuration

Knob

PL104 Mechanism Panel

Ratchet Disc

ST103

Quarter Disc

ST105

White Spacer

ST108

Driver

ST110

Screws

SS112

Black Spacer

ST104

Black Spacer

ST104

Dime Disc

ST107

Inhaltsverzeichnis

Andere Seaga Automat Handbücher

Seaga

Seaga HF2000 Bedienungsanleitung

Seaga

Seaga JDL-2 COMBO Bauanleitung

Seaga

Seaga SM16S Bauanleitung

Seaga

Seaga Naturals2GO NTG4000 Bedienungsanleitung

Seaga

Seaga SL5000 Bedienungsanleitung

Seaga

Seaga Space Saver Series Bedienungsanleitung

Seaga

Seaga OFFICE DELI Fehlerbehebungshandbuch

Seaga

Seaga SP 432 Bauanleitung

Seaga

Seaga INFINITY I4S Bauanleitung

Seaga

Seaga Quick Break Combo QB218 Bedienungsanleitung

Seaga

Seaga Intelligent Inventory Control IQ640 Bauanleitung

Seaga

Seaga Victory Series Bedienungsanleitung

Seaga

Seaga SM16S Bauanleitung

Seaga

Seaga N2G5000 Bedienungsanleitung

Seaga

Seaga ENVISION ENV5 Bauanleitung

Seaga

Seaga INFINITY Series Bauanleitung

Seaga

Seaga Quick Break Combo QB2000 Bauanleitung

Beliebte Automat Handbücher anderer Marken

Godrej

Godrej Minifresh 2000 Bedienungsanleitung

LAUREL

LAUREL 300 Montage- und Bedienungsanleitung

Macas

Macas MACES7C-300-90-00 Series Bedienungsanleitung

Dixie Narco

Dixie Narco SIID Bedienungsanleitung

VendNet

VendNet CB500-SA Bedienungsanleitung

FAS International

FAS International FASTER TMT Bedienungsanleitung

Three Square Market

Three Square Market Kiosk Bedienungsanleitung

Fastcorp

Fastcorp F820 Bauanleitung

Coinco

Coinco BillPro Bedienungsanleitung

Intralot

Intralot OHIO MPNG Bedienungsanleitung

LAVAZZA

LAVAZZA KLIX Series Bedienungsanleitung

Azkoyen

Azkoyen Zensia Handbuch

Azkoyen

Azkoyen STEP 74 Handbuch

SandenVendo

SandenVendo Snack Safety Point SVE SSP Betriebsanleitung

Intralot

Intralot Dreamtouch Smart Bedienungsanleitung

Westomatic

Westomatic Primo Compact Bedienungsanleitung

Crane

Crane Dixie-Narco Glassfront BevMax 3 5800 Bedienungsanleitung

Jofemar

Jofemar Vision Snack Plus Bedienungsanleitung