Sega Triple Play Bedienungsanleitung

OWNERS AND SERVICE MANUAL

INNOVATIVE CONCEPTS IN ENTERTAINMENT INC.

Triple Play

TABLE OF CONTENTS

Safety and Warnings 4

Game Settings and Adjustments 5 - 6

Error Codes 6

Coin setup 7

Card Swipe Install 8-9

Assembly Drawings 10 - 27

Wiring Diagram 29 - 30

Spare List 31

SAFETY AND WARNINGS

BEFORE YOU BEGIN

WARNING: WHEN INSTALLING THIS GAME, A GROUNDED A.C. RECEPTACLE MUST BE USED. FAILURE

TO DO SO COULD RESULT IN INJURY TO YOURSELF OR OTHERS. FAILURE TO USE A GROUNDED RE-

CEPTACLE COULD ALSO CAUSE IMPROPER GAME OPERATION, OR DAMAGE TO THE ELECTRONICS.

DO NOT DEFEAT OR REMOVE THE GROUNDING PRONG ON THE POWER CORD FOR THE SAME REA-

SON AS GIVEN ABOVE. USING AN IMPROPERLY GROUNDED GAME COULD VOID YOUR WARRANTY.

HAVE A QUALIFIED ELECTRICIAN CHECK YOUR A.C. RECEPTACLE TO BE SURE THE GROUND IS FUNC-

TIONING PROPERLY. DO NOT WASH YOUR GAME WITH A PRESSURE WASHER.

AVERTISSEMENT: lors de l'installation de ce jeu, la terre AC récipient doit être utilisé. Ne pas le faire pourrait en-

traîner un préjudice à vous ou à d'autres. Le non-recours à la terre récipient pourrait également causer une mau-

vaise opération de jeu, ou les dommages causés à l'électronique. NE PAS détériorer ou de retirer la broche de

terre sur le cordon d'alimentation pour la même raison, comme indiqué ci-dessus. Indûment l'aide d'un jeu de la

terre pourrait annuler votre garantie. Ont un électricien qualifié de vérifier votre récipient AC pour s'assurer que le

sol fonctionne correctement. Ne lavez pas votre jeu avec une laveuse à pression.

INSTALLATION

The game comes ready to play with just a few simple things to keep in mind.

1. Plug the game into the A.C. outlet and turn on power to the game through the inside of the game next to

the main board assembly. See assembly drawings for location.

THIS GAME IS DESIGNED TO DISSIPATE STATIC ELECTRICITY THROUGH THE GROUNDING PLANE OF THE

GAME. IF THE A.C. GROUND DOES NOT WORK, THE GAME COULD DISCHARGE STATIC ELECTRICITY

THROUGH THE GAME CIRCUITRY, WHICH COULD CAUSE DAMAGE.

2. Make sure the game is level after installation. It is necessary to make sure the game is level for safety

concerns.

3. Check that the A.C. voltage rating on the back of the game matches the A.C. voltage of your location.

THE POWER SUPPLY IS NOT VOLTAGE ADJUSTABLE. TO OPERATE THE GAME AT VOLTAGES OTHER THAN

THOSE IT WAS DESIGNED FOR. PLEASE CONTACT OUR SERVICE DEPARTMENT FOR VOLTAGE CONVER-

SION INFORMATION. WARNING

DO NOT remove any of the components on the main board (e.g. compact flash and eproms) while

the game is powered on. This may cause permanent damage to the parts and the main board. Re-

moving any main board component part while powered on will void the warranty.

Ne retirez pas l'un des composants sur la carte principale (par exemple Compact Flash et

EPROMs), tandis que le jeu est sous tension. Cette mai causer des dommages permanents aux

parties et la carte principale. Suppression de tout bord principal élément sous tension alors que an-

nulera la garantie.

NOTE: THIS GAME IS INTENDED FOR INDOOR USE ONLY.

SHOCK HAZARD - DO NOT OPEN. REFER SERVICING TO SERVICE PERSONNEL.

REMARQUE: CE JEU EST DESTINÉ POUR USAGE À L'INTÉRIEUR SEULEMENT.

AVERTISSEMENT: RISQUE DE CHOC - NE PAS OUVRIR. RÉPARATION À UN PERSONNEL

DE SERVICE.

Game Settings and Adjustments

Your game has been shipped with our recommended defaults for optimal earnings. We have included extra

decals located in your parts package in case you would like to alter the game settings for your location. To

clear audit data press and hold the “UP” button located on the test panel and turn the AC power switch on.

The display will display a random pattern until you release the “Up” button. The game will then clear its au-

dits and reset back in game mode. To reset your game back to factory default settings, press and hold “reset”

button located on the test panel and turn the AC power on. The display will display a random pattern until

you release the “reset” button. The game will revert to default settings and reset back to game mode.

At anytime you can press the “MODE” button located on the test panel to enter programming. Each time you

press the “MODE” button, you advance to the next option. Each option can be changed by either pressing the

“UP” or “DOWN” button also located on the test panel. The game will automatically save the change when

you press the mode button to advance to the next option.

Option Description Values Default

1 Hit Score 2 to 50 15

2 Hit Score 2 to 50 5

3 Hit Score 2 to 50 30

4 Hit Score 2 to 50 10

5 Hit Score 2 to 50 20

6 Jackpot Score 50 to 400 (increments of 50) 150

7 Wheel Speed control 400 to 500 (increments of 20) 440

8 Demo Sound 0 or 1 1

0=all the time

1=each time the coin is inserted

9 Display total ticket payout - See Audits below

10 Display total number of coins - See Audits below

11 Mercy Ticket in Out Hole 0 to 10 1

12 Locked value of Jackpot score 50 to 1000 (increments of 50) 1000

13 Mercy Ticket for Coin in 0 to 5 0

14 LED Stadium Lights - See diagnostics below

15 Limit Switch Tests - See diagnostics below

16 Number of coins outputted by hopper per card swipe. 0 to 50 10

17 Return to game mode, press “reset” located on main pcb.

Audits

Option 9 will display the total amount of tickets paid out. This option can be cleared as described above.

Option 10 will display the total amount of coins in. This option can be cleared as described above.

Test

Option 14 allows you to toggle the LED stadiums lights to ensure each LED is on. Pressing the “UP” button

will turn all LED on and pressing the “DOWN” button will turn them off.

Test (Continued)

Option 15 allows you to test the limit switches found in all the coin out holes. They are called “Home Run

Hole”, “Hit Hole”, and “Out Hole”. When a limit switch is defective, the display will show the hole with the

defective switch and the station number. The station numbers are 1 for red, 2 for blue, and 3 for yellow. A

display of “Ho” means home run hole, a display of “Ht” means Hit hole, and a display of “Ot” means out

hole. This error display can occur when game is first powered up if a switch is “stuck” on. The game will

not function until you enter programming and cycle through to option 16 or replace the defective switch.

Error Codes

At any time during game play, if a error occurs, the following will be displayed:

TICKET ERRORS:

After loading tickets, press the “Ticket Button” to dispense remaining tickets owed.

“Err1” appears on the Jackpot display. This means no ticket in ticket dispenser 1.

“Err2” appears on the Jackpot display. This means no ticket in ticket dispenser 2.

“Err3” appears on the Jackpot display. This means no ticket in ticket dispenser 3.

SENSOR ERRORS:

“ErrC” appears on the Jackpot display. This means the count sensor has failed.

“ErrZ” appears on the Jackpot display. This means the Home sensor has failed.

“ESSS” appears on the Jackpot Display. This means both sensors have failed.

A note on Sensor Failures:

The game expects a steady pulse from the count sensor and when the playfield has gone a full revolu-

tion a pulse is received by the home sensor. If after a period of time the home sensor is not seen, the game

will display the “ErrZ” error. Ensure that the home sensor flag triggers the top sensor when a full revolution

is done. If the playfield is not turning smoothly, this will cause the count sensor to become erratic and dis-

play a “ErrC” on the jackpot display. Check underneath the playfield to ensure that none of the brackets are

moving or have become loose. It might be necessary to remove one coin chute above the coin drawer to ac-

cess the assembly. Please refer to the assembly diagrams for details. Total sensor failure will display a

“ESSS” meaning it cannot see both the count sensor or home sensor. Check to ensure there is no physical

damage to the sensor has occurred.

COIN SWITCH ERRORS:

When the game is powered on it will self check for stuck switches before entering game mode. If any

switch is found to be stuck, the game will display the error switch location code and will not enter game mode.

You can force the game into game mode by pressing mode button 16 times if it is not possible to repair at that

time. It is highly recommended to attended to this error as soon as possible.

“Ho1” appears on the jackpot display. Defective switch located in the “Home run hole” on red station.

“Ho2” appears on the jackpot display. Defective switch located in the “Home run hole” on blue station.

“Ho3” appears on the jackpot display. Defective switch located in the “Home run hole” on yellow station.

“Ht1” appears on the jackpot display. Defective switch located in the “ Hit hole” on red station.

“Ht2” appears on the jackpot display. Defective switch located in the “Hit hole” on blue station.

“Ht3” appears on the jackpot display. Defective switch located in the “Hit hole” on yellow station.

“Ot1” appears on the jackpot display. Defective switch located in the “Out hole” on red station.

“Ot2” appears on the jackpot display. Defective switch located in the “Out hole” on blue station.

“Ot3” appears on the jackpot display. Defective switch located in the “Out hole” on yellow station.

SETUP - ASSEMBLY

This game has three stations that require you to insert your game room token or the

coin you wish to use into each of the coin comparators before they will accept any

coins or tokens. You will also need to load tickets into each station’s ticket dispenser.

See below for loading coins or tokens.

NOTE: RED STATION PICTURES SHOWN BELOW

STEP 1: At each station open the coin door to

access the coin comparator.

STEP 2: Pull back the coin holder and insert

your coin into the coin slot.

STEP 3: Release coin holder and close coin

door.

Card Swipe Installation

The game has been designed for easy integration of any card swipe system. You will find in the cash box all

the necessary hardware to install hoppers into each station. Hoppers and harnesses are not included and can

be obtained from ICE Service Department.

To convert your game to card swipe you will need to install a coin cup and hopper into each station.

Step 1:

Remove the four mounting screws to the front cover of the coin return chute found above each cash box.

Step 2:

Locate the bottom bracket plate and attach the mount for the hopper with four screws.

Step 3:

Slide the hopper and bracket assembly into the opening of the coin chute. You will need to slide the assem-

bly back and then to the left to install the four mounting screws shown below.

Card Swipe Installation (Continued)

Step 4:

Locate the coin out ramp and position it in front where the coins are dispensed from the hopper and install the

two mounting screws.

Step 5:

Remove the coin chute plate from the door and install the coin cup with remaining hardware.

The remaining steps to finish your card swipe installation is different per card swipe system used. Refer to

your owners manual of your card swipe for further information.

The main logic board can directly control the hoppers. A wire harness from the hoppers to the main board

can be purchased form ICE Service Department. The default payout per swipe is 10 coins. This can be ad-

justed in the games settings. This game also has separate coin and ticket meters for each station located

above the main logic board. It is recommended to disconnect the meters and directly connect to your card

swipe system. Refer to the wiring diagrams from detail information.

Location Part number Description QTY

1 Lower cabinet 1

2 Upper cabinet 1

3 Lower Bat assembly 6

4 Ticket door assembly 3

5 Main PCB door 1

6 Coin station assembly (Red, blue, yellow) 3

7 Jackpot display assembly (Red, blue, yellow) 3

9 Coin collector platform assembly 3

8 Stadium light assembly 6

10 See page 25 Playfield base plate assembly 1

11 Center acryl playfield 1

12 XHAT3027X Right and left side window acryl set 6

13 XHAT3001 Acryl dome 1

14 Dome bracket 1

15 XHAT7001TP Title panel 3

1 15

Cabinet Assembly

Inhaltsverzeichnis

Andere Sega Arcade-Spielautomat Handbücher

Sega

Sega The House Of The Dead 4 29"STD Bedienungsanleitung

Sega

Sega Ghost Squad Bedienungsanleitung

Sega

Sega MARIO & SONIC AT THE OLYMPICS GAMES TOKYO... Bedienungsanleitung

Sega

Sega World Series Baseball Super Major League Bedienungsanleitung

Sega

Sega Luigi's Mansion Arcade Anwendungshandbuch

Sega

Sega Giant Plants vs Zombies The Last Stand Bedienungsanleitung

Sega

Sega HOUSE OF THE DEAD 4 SUPER DELUXE Bedienungsanleitung

Sega

Sega SHOOT THIS WIN THIS Bedienungsanleitung

Sega

Sega THE HOUSE OF THE DEAD III DELUXE Bedienungsanleitung

Sega

Sega Star Wars Trilogy Bedienungsanleitung

Sega

Sega Virtua Striker 4 Bedienungsanleitung

Sega

Sega Derby Owners Club World Edition Bedienungsanleitung

Sega

Sega Racing Classic Bedienungsanleitung

Sega

Sega Grid 42 Bedienungsanleitung

Sega

Sega NAOMI Bedienungsanleitung

Sega

Sega Daytona USA Bedienungsanleitung

Sega

Sega AV F-ZERO AX Bedienungsanleitung

Sega

Sega PIRATES of MONSTER ISLAND Bedienungsanleitung

Sega

Sega NAOMI 2 Bedienungsanleitung

Sega

Sega PRIMEVAL HUNT Bedienungsanleitung

Sega

Sega Olle King Bedienungsanleitung

Sega

Sega MISSION: IMPOSSIBLE Bedienungsanleitung

Sega

Sega OUTRUN 2 SPECIAL TOURS DELUXE Bedienungsanleitung

Sega

Sega SOUL SURFER Bedienungsanleitung

Beliebte Arcade-Spielautomat Handbücher anderer Marken

Universal Space

Universal Space COCONUT BASH Bedienungsanleitung

Bay-Tek

Bay-Tek EVOLVE Bedienungsanleitung

Global VR

Global VR America's Army Montage- und Bedienungsanleitung

Atronic

Atronic Cashline Bedienungsanleitung

Universal Space

Universal Space Checky Monkey Bedienungsanleitung

Bay-Tek

Bay-Tek Skee Ball 1908 Alley Bedienungsanleitung

Aristocrat Technologies

Aristocrat Technologies Mars X Upright Bedienungsanleitung

Family Fun Companies

Family Fun Companies Reactor Kurzanleitung

Universal Space

Universal Space FRUIT MANIA Extreme Bedienungsanleitung

falgas

falgas CARRUSEL FIESTA Bedienungsanleitung

Konami

Konami DanceDanceRevolution Bedienungsanleitung

Bay-Tek

Bay-Tek quik drop Bedienungsanleitung

Bandai Namco

Bandai Namco PAC-MAN BATTLE ROYALE CHOMPIONSHIP DELUXE Bedienungsanleitung

Adrenaline

Adrenaline Flying Tickets Montage- und Bedienungsanleitung

Swinks

Swinks Stern Pinball Ghostbusters Bedienungsanleitung

Innovative Concepts in Entertainment

Innovative Concepts in Entertainment MONOPOLY ROLL-N-GO Bedienungsanleitung

jakar

jakar SPEED CARS Bedienungsanleitung

Carmelli

Carmelli HAT TRICK NG1015H Bedienungsanleitung