Shuttle HOT-683 Bedienungsanleitung
HOT-683
PPGACeleronprocessor
Based AGP MAIN BOARD
User's Manual
- 2 -
FCC Notice:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy. If not installed and used properly, in strict accor-
dance with the manufacturer’s instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures :
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/television technician for help and for additional suggestions.
The user may find the following booklet prepared by the Federal Communications Commission helpful “How to Identify
and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Office.
Washington, DC 20402, Stock 004-000-00345-4
FCC Warning
The user is cautioned that changes or modifications not expressly approved by the manufacturer could void the user’s
authority to operate this equipment.
Note : In order for an installation of this product to maintain compliance with the limits for a Class B device, shielded
cables and power cord must be used.
CE Notice:
Following standards were applied to this product, in order to achieve compliance with the electromagnetic
compatibility :
- Immunity in accordance with EN 50082-1: 1992
- Emissions in accordance with EN 55022: 1987 Class B.
NOTICE
Copyright 1998.
All Right Reserved
Manual Ver 1.0
All information, documentation, and specifications contained in this manual are subject to change without prior
notification by the manufacturer.
The author assumes no responsibility for any errors or omissions which may appear in this document nor does
it make a commitment to update the information contained herein.
TRADEMARKS
Intel is a registered trademark of Intel Corporation
PPGA Celeron Processor is a registered trademark of Intel Corporation
PC/AT is a registered trademark of International Business Machine Corporation.
PS/2 is a registered trademark of IBM Corporation.
All other brand and product names referred to in this manual are trademarks or registered trademarks of their
respective holders.
- 3 -
T
T
PREFACE .............................................................................................................. 4
CHAPTER 1 INTRODUCTION....................................................................................... 5
Specification................................................................................................................................ 5
Accessories of HOT-683 ............................................................................................................. 7
CHAPTER 2 HARDWARE CONFIGURATION .................................................................... 8
The PPGA Celeron Processor ...................................................................................................... 8
Jumpers ....................................................................................................................................... 9
CPU Clock Speed Selection - JP5................................................................................................ 9
Clear CMOS - JP10 ................................................................................................................... 10
Keyboard & PS/2 Mouse Power-on Setting - JP2 ...................................................................... 10
Connectors ................................................................................................................................ 11
CHAPTER 3 MEMORY CONFIGURATION ..................................................................... 14
CHAPTER 4 FLASH UTILITY .................................................................................... 15
CHAPTER 5 AWARD BIOS SETUP .......................................................................... 17
The Main Menu ......................................................................................................................... 18
Standard CMOS Setup............................................................................................................... 20
BIOS Features Setup ................................................................................................................. 22
Chipset Features Setup .............................................................................................................. 25
Power Management Setup ......................................................................................................... 29
PCI Configuration Setup ........................................................................................................... 32
Integrated Peripherals ................................................................................................................ 34
Password Setting ....................................................................................................................... 37
TABLEOF CONTENTS
- 4 -
P
P
HOT-683 is a highly integrated IBM PC/ATX compatible system board designed to
meet the industry's most demanding desktop applications.
Based on the Intel 82440LX AGPset chipset which support up to 400MHz PPGA
Celeron processor with MMX technology.
HOT-683 is equipped with an Accelerated Graphics Port (A.G.P.), a high-performance
interconnect for graphic-intensive application, such as 3D applications. The A.G.P. is
independent of the PCI bus and is designed to exclusively use with graphical-display
devices. The HOT-683 supports 3.3 V A.G.P. devices with data transfer rates up to 133
MHz, allowing data throughput of 500 MB/sec.
The Intel's 82440LX AGPset chipset provides an integrated Bus Mastering IDE control-
ler with two high performance IDE interfaces which allows up to four IDE devices
connection and up to 33 MB/sec of data transfer rates.
The on-board I/O controller provides standard PC I/O functions:
floppy drive interface, two FIFO serial ports, an InDA device port and a SPP/EPP/ECP
capable parallel port.
HOT-683 is built with four PCI local bus slots providing a high bandwidth data path for
data-movement intensive functions such as graphics, and with three ISA slot.
HOT-683 provides the foundation for cost effective, high performance and highly
expandable platforms, which delivers the latest in the Intel PPGA Celeron processor and
new advanced chipset technology.
PREFACE
- 5 -
1
1
The HOT-683 Mainboard is carefully designed for the demanding PC user who wants high perfor-
mance and many intelligent features in a compact package:
Intel Chipset:
Features Intel's 440LX AGPset with I/O subsystems.
CPUSupport:
Intel PPGA Celeron processor 300/66, 333/66, 366/66, 400/66 MHz.
Versatile Memory Supports:
Supports three banks of SDRAM or EDO DRAM maximum memory size up to 384MB.
Configurable support for ECC (Error Checking and Correcting)
PCIand ISA ExpansionSlots:
Provides four 32-bit PCI slots and three 16-bit ISA slot.
Onboard I/O:
Provides one Floppy port; one PS/2 mouse and one PS/2 Keyboard port connector; two high-speed
UART compatible serial ports and one parallel port with ECP and EPP capabilities. Serial Port 2
can also be directed from COM2 to the Infrared Module for wireless connections.
OnboardPCI Bus Master IDEController:
Two Ultra DMA/33 Bus Master IDE Ports supports four IDE devices up to 33 MB/sec IDE trans-
fers and supports Enhanced PIO Modes 3 and 4 and Bus Master IDE DMA Mode 2 devices.
Onboard20-pin ATX PowerSupply:
Provides ATX power connector onboard supports soft-on/off function.
System BIOS:
Provides licensed Award V4.51PG BIOS on Flash EEPROM.
Supports Green PC, DMI and Bundled with NCR SCSI BIOS.
ACPI:
Support ACPI (Advanced Configuration and Power Interface) function. ACPI provide more
Energy Saving Features for the future operating system supporting OS Direct Power Management
(OSPM) functionality.
INTRODUCTION
- 6 -
Board Size:
MicroATX form factor 305mm x 170mm.
Advanced Features:
CPU Plug & Play -- HOT-683 featuring CPU Plug & Play function, the user needn't to adjust
onboard system clock and CPU multiplier. When the system first power-on, BIOS will set CPU
clock speed to 300 MHz (depend on CPU external frequency) automatically. If your CPU speed
higher than 300 MHz, one thing you only have to do is entry BIOS to set CPU speed to the higher
one.
Low EMI -- Spread Spectrum built in - ±0.5% or ±0.3% modulation and automatic clock shut-off
of unused PCI/SDRAMS slots to reduce the EMI.
Dual Function Power Button -- The system can be one of two states, one is Suspend mode and
the other is the Soft-off mode. Pushing the power button for less than 4 seconds will place the
system into Suspend mode. When push the power button for more than 4 seconds, the system
enters the Soft-off mode.
Wake-On-LAN -- The system will power-on automatically by activating of LAN.
(This function support Intel LAN card only).
Modem Ring Power-on -- The system will power-on automatically by activating of modem ring.
PS/2 Keyboard & Mouse Power-on -- The system will power-on automatically by stroke key-
board or double click PS/2 mouse.
Voltages Monitoring -- System voltages levels are monitored to ensure stable current to main
board components.
System voltages include VCORE and VTT for CPU, and +5V, +12V, -5V, -12V for system.
FAN Status Monitoring -- To prevent CPU overheat, CPU fans is monitored for RPM and failure.
(CPU Cooling FAN with RPM sensor is required)
- 7 -
ACCESSORIESOF HOT-683
- 8 -
2
2HARDWARECONFIGURATION
HOT-683 mainboard provides a 370-pin ZIF Socket370 for Intel PPGA Celeron CPU. The
CPU that came with the mainboard should have a fan attached to it to prevent overheating. If
this is not the case then purchase a fan before you turn on your system.
To install a CPU, first turn off your system and remove its cover. Locate the ZIF Socket370
and open it by first pulling the lever sideways away from the socket then upwards to a 90-
degree right angle. Insert the CPU with the correct orientation as shown.(Figure 2-1) Use
the notched corner of the CPU as your guide. The notched corner should point towards the
end of the lever. Notice that there are two blank area where one hole is missing from that
corner of the square array of pin holesr. Because the CPU has a corner pin for two of the
four corner, the CPU will only fit in the one orientationn, hold down on the CPU and close
the socket’s lever.
The Installation PPGA Celeron Processor
Figure 2-1
Figure 2-2
Then you should have a CPU fan that
will cover the face of the CPU. Apply
thermal jelly to the CPU metallic top and
then install the fan onto the CPU. (Figure
2-2 )
- 9 -
Jumpers
Several hardware settings are made through the use of jumper caps to connect jumper pins on
the main board. The jumper's pin 1 on main board will be on the top or on the left when hold-
ing the main board with the keyboard connector away from yourself.
Jumpers with two pins will be shown as for Close (On) and for Open (Off).
To connect the pins, simply place a plastic jumper cap over the two pins.
CPU Clock Speed Selection - JP5
HOT-683 featuring CPU Plug & Play function, the user needn't to adjust onboard system clock
and CPU multiplier.
HOT-683 mainboard features a clock generator to provide adjustable system clock frequency.
JP5 is a 6-pin jumpers which determine the system clock frequency 50 MHz to 83 MHz.
HOT-683 mainboard does not provide any jumper to figure the CPU multiplier since the
multiplier adjusting function is not available on PPGA Celeron.
Figure 2-3 shows the position of JP5 on the mainboard. Table 2-1 shows adjustable System
clock on jumper JP5.
Figure 2-3
SystemClock
(JP5) 1-2 3-4 5-6
50 MHzONONON
60 MHzONOFF OFF
66 MHzOFF OFF OFF
75 MHzOFF ONOFF
83 MHzONOFF ON
Table 2-1
- 10 -
Clear CMOS - JP10
HOT-683 mainboard supports jumper JP10 for discharging mainboard's CMOS memory.
This jumper can clear the CMOS data stored in the Giga I/O chip. To clear the CMOS data
please follow listed steps:
1) Turn off the PC,
2) Remove mini jumper from JP10 pin 1-2,
3) Insert mini jumper to JP10 pin 2-3 for a brief while,
4) Remove mini jumper from JP10 in 2-3,
5) Reinsert mini jumper to JP10 pin 1-2,
6) Turn on the PC.
Keyboard & PS/2 Mouse Power-On Setting - JP2
HOT-683 mainboard provides an optional power-on function by stroke any key (or hot-key)
on keyboard or double click on PS/2 mouse.
Note: Power-on by serial mouse is not supported
JP2 is the jumper used to set the functions of keyboard & PS/2 mouse power-on Enabled or
Disabled.
When you enabled K/B & PS/2 Mouse Power-ON function, you also have to set the proper
item on POWER ON function category of Integrated Peripherals of BIOS setup.
Table 2-2
Figure 2-4 Figure 2-5
K/B&PS/2Mouse Power-OnJP2
Keyboard&
PS/2Mouse
Power-On
Disabled
PS/2Mouse
Power-On
Enabled
Keyboard&
PS/2Mouse
Power-On
Enabled
Inhaltsverzeichnis
Andere Shuttle Hauptplatine Handbücher
Shuttle
Shuttle MT63 Bedienungsanleitung
Shuttle
Shuttle ME21 Bedienungsanleitung
Shuttle
Shuttle HOT-637 Bedienungsanleitung
Shuttle
Shuttle Spacewalker HOT-687 Bedienungsanleitung
Shuttle
Shuttle FN85 Bedienungsanleitung
Shuttle
Shuttle HOT-661/P Bedienungsanleitung
Shuttle
Shuttle FT61 Bedienungsanleitung
Shuttle
Shuttle HOT-679 Bedienungsanleitung
Shuttle
Shuttle HOT-433 Bedienungsanleitung
Shuttle
Shuttle HOT-579 Bedienungsanleitung
Shuttle
Shuttle Spacewalker MV11 Bedienungsanleitung
Shuttle
Shuttle FN25 Bedienungsanleitung
Shuttle
Shuttle Spacewalker MK20 Bedienungsanleitung
Shuttle
Shuttle AK32E Bedienungsanleitung
Shuttle
Shuttle HOT-595 Bedienungsanleitung
Shuttle
Shuttle MB11 Bedienungsanleitung
Shuttle
Shuttle AK10 Bedienungsanleitung
Shuttle
Shuttle AV49V Bedienungsanleitung
Shuttle
Shuttle Spacewalker AK32 Bedienungsanleitung
Shuttle
Shuttle FB83 Bedienungsanleitung
Beliebte Hauptplatine Handbücher anderer Marken
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Bedienungsanleitung
Gigabyte
Gigabyte GA-9IVDT Bedienungsanleitung
Texas Instruments
Texas Instruments ADS8372EVM Bedienungsanleitung
Commell
Commell MS-C73 Bedienungsanleitung
IBT Technologies
IBT Technologies MB860 Bedienungsanleitung
Nvidia
Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung
