Siemens Simatic RF382R Scanmode Bedienungsanleitung

J31069-D0214-U001-A1-7618, 10/2009 1

SIMATIC Sensors

RFID systems

SIMATIC RF382R Scanmode

Operating Instructions (Compact)

Characteristics

RF382R Scanmode Characteristics

Operating range Suitable for high speeds, e.g. in

● Suspension conveyor systems

● Assembly lines

● Production

● Order picking

Antenna field Designed for transponders that are directed

sideways past the long side of the antenna.

See Chapter Transmission window (Page 3)

Read distance Depending on transponder; see Field data for

MDS and SLG (Page 6)

Degree of protection IP67

Ordering data

Table 1 RF382R Scanmode ordering data

Product Order No.

RF382R Scanmode 6GT2801-3AB20-0AX0

Table 2 RF382R Scanmode ordering data for accessories

Accessories Order No.

Simatic Sensors connecting cable, length: 5 m 6GT2891-0FH50

Simatic Sensors RF380R connecting cable RS232 6GT2891-0KH50

Wide-range power supply 24 V, 4 A, with Euro plug 6GT2898-0AA00

Wide-range power supply 24 V, 4 A, with UK plug 6GT2898-0AA10

Wide-range power supply 24 V, 4 A, with US plug 6GT2898-0AA20

Safety instructions for the device/system

NOTICE

This device/system may only be used for the application instances that have been described in the catalog and the

technical documentation "SIMATIC RF300 System Manual

(http://support.automation.siemens.com/WW/view/en/21738946)" and only in combination with third-party devices and

components recommended and/or approved by Siemens.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the

equipment

SIMATIC RF382R Scanmode

2 J31069-D0214-U001-A1-7618, 10/2009

Pin assignment RF382R Scanmode RS232 interface

You can connect the RF382R Scanmode reader via the internal RS232 interface or via a higher-level system. Pay attention

to the correct assignment of the pins.

Table 3 Connector and reader pin assignment

Pin Pin

Device end 8-pin M12

Assignment

1 + 24 V

2 RXD

3 0 V

4 TXD

5 must not be connected

6 must not be connected

7 must not be connected















8 Ground (shield)

Display elements of the RF382R Scanmode reader

Table 4 LED display elements on the reader

Color Meaning

Green Operating voltage present, reader ready for operation

Yellow Transponder present

Red Red LED for error display is activated permanently if correct operation of the reader cannot be guaranteed

(e. g. faulty start, checksum error during operation).

SIMATIC RF382R Scanmode

J31069-D0214-U001-A1-7618, 10/2009 3

Transmission window

Orientation of magnetic fields of the SIMATIC RF382R Scanmode

For many applications it may be best to operate the reader so that the tags move from left to right (or from right to left) at a

certain distance in front of the narrow edge of the reader. This direction of movement uses the horizontal magnetic field of

the reader, see figure below.

You also have the option of moving the tags up and down (or down and up) past the narrow edge of the reader. This

direction of movement uses the vertical magnetic field of the reader.

KRUL]RQWDO

YHUWLFDO

Figure 1 Definition of horizontal and vertical magnetic reader field

Maximum magnetic field strength

The reader creates the maximum magnetic field about 13 mm below the upper reader edge. For the largest possible reading

range the tags you want to read should move in this range. This applies whether you use the horizontal or the vertical

magnetic field.

'RSW PP

Figure 2 Line of maximum magnetic field strength

The area of the maximum field strength and, therefore, the maximum range is identified by a laser icon:

Figure 3 Laser icon marking

SIMATIC RF382R Scanmode

4 J31069-D0214-U001-A1-7618, 10/2009

Transmission window for horizontal magnetic field







+RXVLQJHGJH

&RYHUHGJH

0'6

0HDVXULQJSRLQW

Figure 4 Distance definition for horizontal magnetic field

Green Main field (processing field)

Blue Secondary fields, horizontal magnetic field

L Maximum length of the main field, horizontal magnetic field

d Distance from the reader edge at which maximum horizontal main field length L exists

Sa Operating range in the main field

Sg Limit distance

① Level 1

② Level 2

③ Level 3

⇒ Direction of motion of the transponder

Operating range (Sa)

The operating range lies between Level ① and Level ③.

The operating range between Levels ① and ② includes secondary fields.

The recommended operating range therefore lies in the green main field between Level 2 and Level 3.

Limit distance (Slim)

The limit distance lies on Level ③.

SIMATIC RF382R Scanmode

J31069-D0214-U001-A1-7618, 10/2009 5

Transmission window for vertical magnetic field

G6J

RSW

0HDVXULQJSRLQW

7DJHGJH 0'6

Figure 5 Distance definition vertical magnetic field

Green Main field (processing field)

L Maximum length of the main field, horizontal magnetic field

d Distance from the reader edge at which maximum horizontal main field length L exists

Sa Operating range in the main field

Sg Limit distance

Dopt = 13 mm

⇓ Direction of motion of the transponder

SIMATIC RF382R Scanmode

6 J31069-D0214-U001-A1-7618, 10/2009

Field data for MDS and SLG

The following tables show the field data of transponders with SIMATIC RF382R Scanmode. The technical specifications

listed below are typical data and apply at an ambient temperature of +22 °C.

Tolerances of ±20% are admissible due to production and temperature conditions.

Field data horizontal field

Table 5 Length of the transmission window L

MDS D124 MDS D160 MDS D324 MDS D424 MDS D460

60 50 60 65 50

All dimensions in mm

Table 6 Usable field width with dynamic operation (median deviation) in mm

MDS D124 MDS D160 MDS D324 MDS D424 MDS D460

20 20 20 20 20

All dimensions in mm

Table 7 Operating range

MDS D124 MDS D160 MDS D324 MDS D424 MDS D460

40…65 35….50 40…65 40…65 30…50

All dimensions in mm

Table 8 Limit distance

MDS D124 MDS D160 MDS D324 MDS D424 MDS D460

75 65 75 75 60

All dimensions in mm

Field data vertical field

Table 9 Length of the transmission window at different distances d (reader tag edge)

d (mm) MDS D124 MDS D160 MDS D324 MDS D424 MDS D460

2 155 130 155 150 120

10 150 125 150 145 115

20 140 110 140 135 105

30 130 100 130 120 90

All dimensions in mm

SIMATIC RF382R Scanmode

J31069-D0214-U001-A1-7618, 10/2009 7

Table 10 Usable field width with dynamic operation (median deviation)

MDS D124 MDS D160 MDS D324 MDS D424 MDS D460

25 25 25 25 25

All dimensions in mm

Table 11 Operating range in mm (Sa)

MDS D124 MDS D160 MDS D324 MDS D424 MDS D460

10…25 10…25 10…25 10…25 10…25

All dimensions in mm

Table 12 Limit distance in mm (Sg)

MDS D124 MDS D160 MDS D324 MDS D424 MDS D460

75 65 75 75 60

All dimensions in mm

Note

Tips if the range is too short

If the range of the antenna is too short, you must check

● the power supply/switched-mode power supply (interference)

● whether there are monitors or other sources of interference nearby

● whether there is metal in the environment

Minimum distance from transponder to transponder (without multitag mode), in mm

The values are valid at a distance of 20 mm (reader-tag).

Table 13 Minimum distance transponder

MDS D124 to

MDS D124

MDS D160 to

MDS D160

MDS D324 to

MDS D324

MDS D424 to

MDS D424

MDS D460 to

MDS D460

Horizontal main

field

100 100 100 100 100

Vertical main field 150 120 150 180 120

The minimum distance can be undershot in multitag mode.

NOTICE

Extension of the data transmission time if distance values are undershot

If the distance values specified in the tables are undershot, it is possible that the inductive fields will be affected. The time

required for data transmission can increase unpredictably.

For this reason, please observe the values in the tables.

SIMATIC RF382R Scanmode

8 J31069-D0214-U001-A1-7618, 10/2009

Traversing speed with RF382R Scanmode

The following table shows the traversing speed of a transponder through the main field. The direction of motion of the

transponder is horizontal.

Table 14 Traversing speed of different transponders

MDS D124 MDS D160

MDS D460

MDS D324

MDS D424

UID number

(8 bytes)

1.5 m/s 1.5 m/s 1.5 m/s

Mounting on metal

The RF382R can be mounted directly on metal. Flush mounting on metal is not permitted.

Minimum distance between several RF382R Scanmode readers

Figure 6 Minimum distance between several RF382R Scanmode readers

Minimum distance D from RF382R to RF382R D ≥ 200 mm

SIMATIC RF382R Scanmode

J31069-D0214-U001-A1-7618, 10/2009 9

Setting the parameters of the RF382R

Certain parameters of the scan mode can be changed during operation. These parameters are transferred from the host to

the reader via the serial interface for this purpose.

You can change the following parameters this way:

● ScanMode: Single Read (single reading of a tag) or Continuous Read (continuous reading of a tag)

● LockTime: Lock time for the setting "Continuous Read"

● Retentive: The parameters are stored in the non-volatile Flash memory of the reader.

The interface parameters for transfer are set permanently to 38400, 8, n, 1. This data sequence can be easily integrated into

an existing application because the parameter assignment frame is open.

Structure of the parameter assignment frame to the reader

You can transfer a new parameter set to the reader at any time during operation. When a parameter set is received, scan

mode will be interrupted, and the new parameters are checked and adopted if they are found to be "good". Scan mode will

start up immediately once the parameters have been accepted.

Note

Data will be lost during parameter setting (which means from receipt of a parameter frame until acknowledgment) if

operation continues.

The parameters are either saved in RAM (status = 00) only or retentively (status = 01). The command for transmission of

parameters ("Para") is 01.

Data backup takes place with a simple EXOR operation (BCC) of all data bytes to be transferred.

The parameters will be transferred as a data sequence (message frame). The following parameters can be modified:

● "LockTime" parameter; you can set values of 0..65535 (time base 100 ms)

● "ScanMode" parameter; you can set ContinousRead (00) and SingleRead (01)

All the other parameter bytes are reserved for future use and have to be assigned with 0.

Sending parameters to the reader

Command

byte

"Para"

Status 1st byte

(res.)

… 6th byte

"ScanMode"

7th byte

"LockTime"

(HighByte)

8th byte

"LockTime"

(LowByte)

… 21st byte

(res.)

BCC

The command message frame consists of 24 bytes that you always have to transfer completely.

Acknowledgment of the reader

Acknowledgment

byte

"Para"

Error code BCC

The acknowledgment message frame consists of three bytes. The acknowledgment byte is identical to the command byte.

The error code is zero if the parameters are accepted without errors. An error code other than zero means that the

parameters have not been accepted. The following error codes are defined:

01 The command byte is incorrect (only "Para" is permitted)

02 The status byte is incorrect (RAM or retentive only)

03 The Scanmode parameter is incorrect (ContinousRead and SingleRead permitted only)

04 The BCC value in the parameter message frame is incorrect.

05 Data could not be saved retentively (error with Flash type request)

06 Data could not be saved retentively (error with Flash delete)

07 Data could not be saved retentively (error with Flash writing)

SIMATIC RF382R Scanmode

10 J31069-D0214-U001-A1-7618, 10/2009

Technical specifications

Table 15 RF382R technical specifications

Inductive interface to the MDS

Transmission frequency 13.56 MHz

Transmit power Approx. 0.7 W

Supported transponders (reader air interface) Transponder to ISO 15693

Antenna Integrated, horseshoe shape

HOST interface RS232

Baud rate 38400 baud

Read distances of the reader See Chapter Field data for MDS and SLG (Page 6)

Minimum distance between two RF382R Scanmode readers 200 mm

Cable length reader - HOST max. 30 m

Maximum data transmission rate

transponder (tag) - reader (reading)

600 byte/s

Functions Read transponder serial number

Power supply 24 V DC

Display elements 2-color LED

(operating voltage, presence, error)

Plug connector M12 (8-pin)

Housing

● Dimensions (in mm)

● Color

● Material

● 160 x 80 x 41 (without M12 device connector)

● Anthracite

● Plastic PA 12

Mounting 4 x M5 screws

Ambient temperature

● Operation

● Transport and storage

● -25 °C to +70 °C

● -40 °C to +85 °C

Degree of protection to EN 60529

Shock to EN 60721-3-7 Class 7 M2

Vibration to EN 60721-3-7 Class 7 M2

IP67

50g

20g

Weight approx. 550 g

MTBF (Mean Time Between Failures) 1 x 106 h

Approvals Radio to R&TTE guidelines EN 300 330,

EN 301489, CE

Current consumption typ. 140 mA

Max. power consumption (DC input) 3.5 W

Andere Handbücher für Simatic RF382R Scanmode

Inhaltsverzeichnis

Andere Siemens Zubehör Handbücher

Siemens

Siemens Milltronics Millpulse 600 Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens 5WG1 258-3AB11 Bedienungsanleitung

Siemens

Siemens SIWAREX WP251 Bedienungsanleitung

Siemens

Siemens SITRANS F C MASS 2100 DI 1.5 Bedienungsanleitung

Siemens

Siemens SIWAREX JB Bedienungsanleitung

Siemens

Siemens SITRANS TS100 Administratorhandbuch

Siemens

Siemens SITRANS CU02 Bedienungsanleitung

Siemens

Siemens Symaro QAA2890/WI Bedienungsanleitung

Siemens

Siemens SITRANS F Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Siemens

Siemens QPM11 Series Bedienungsanleitung

Siemens

Siemens Sitrans WM100 Bedienungsanleitung

Siemens

Siemens 5WG1 201-2DBx3 Series Bedienungsanleitung

Siemens

Siemens Milltronics RBSS Bedienungsanleitung

Siemens

Siemens SITRANS F M MAG 1100 Bedienungsanleitung

Siemens

Siemens RUGGEDCOM WIN7014 Bedienungsanleitung

Siemens

Siemens adm-i12w2 Bedienungsanleitung

Siemens

Siemens SIMATIC MOBY D Benutzerhandbuch

Siemens

Siemens SITRANS LR 400 Leitfaden

Siemens

Siemens QAM2151.040/MO Bedienerhandbuch

Siemens

Siemens SITRANS FSS200 Bedienungsanleitung

Siemens

Siemens SIMATIC RF640A Bedienungsanleitung

Siemens

Siemens jpQO Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung

Axminster

Axminster Tooling Stylus Tip Ballpoint Pen Kit Bedienungsanleitung