Siemens SITRANS FC430 Kurzanleitung

A5E33338888-AG, 06/2016 1

FC430 upgrade instructions - Remote

Product Information

Introduction

The purpose of these upgrade instructions is to assist technicians in upgrading the FC430 system from sales release 1 (HW

revision 1 and FW version 2.00.02-**).

The instructions are aimed at service and maintenance technicians.

Items supplied

FC430 upgrade package for remote systems, A5E34574778, contains the following components:

Component

Photo

SITRANS FCS400 DSL cassette

4 GB micro SD card (SensorFlash) with Micro SD

card adapter containing:

•Firmware bundle

•Upgrade instructions

Note: Firmware bundle and upgrade instructions may

also be downloaded from the Intranet at:

(http://support.automation.siemens.com/WW/view/en/

60666565/133300)

Power supply unit

FC430 Upgrade instructions - Remote

Order number: A5E33338888

FC430 upgrade package for remote version

FC430 upgrade instructions - Remote

2A5E33338888-AG, 06/2016

Upgrading the FC430 system

Overview

The upgrade procedure includes the following main steps:

1. Remove and back up SensorFlash (SD card) (Page 2)

2. Replace power supply (Page 3)

3. Replace DSL cassette (Page 6)

4. Upgrade firmware (Page 8)

5. Synchronize data (Page 8)

Before carrying out any repair work, the instructions for safe handling of the device must be read and understood. See

Operating Instructions.

Remove and back up SensorFlash (SD card)

①

Isolate the device from power.

②Unscrew the locking screw of the display lid and remove lid.

③Using a plain screwdriver, carefully release the display as shown in the following photo.

FC430 upgrade instructions - Remote

A5E33338888-AG, 06/2016 3

④

Remove the SensorFlash (SD card) from the transmitter. Insert the SensorFlash into a PC using the SD card

adapter and create a backup of all files from the card to a PC.

Note: Do not re-insert the SD card in the transmitter at this point. You will need the SensorFlash again later, see

Synchronize data (Page 8).

Replace power supply

Remove sensor cassette

①Remove the two screws that hold the sensor cassette.

②

Pull out the sensor cassette to the position shown in the photo. Disconnect the cable by pinching the plug with a pair

of point nose pliers while carefully pulling out the plug.

FC430 upgrade instructions - Remote

4A5E33338888-AG, 06/2016

Remove transmitter and I/O cassettes

①

Remove the two screws that hold the transmitter I/O cassettes.

②Pull out the two cassettes.

Remove power supply

①Unscrew three fixing screws for power supply cover and pull out the cover.

FC430 upgrade instructions - Remote

A5E33338888-AG, 06/2016 5

②

Using a pair of point nose pliers, pull out the triangular housing with the power supply cassette.

Install new power supply

Insert the new power supply delivered with the upgrade kit as follows:

①Carefully slide the new power supply into the triangular housing and reinsert in the transmitter.

②

Reinsert I/O and transmitter cassettes.

Insert sensor cassette as follows:

③Hold down the cable while pushing the sensor cassette to the position shown in the photo.

④

Reconnect cassette cable plug and push sensor cassette into place. Fasten the two screws.

FC430 upgrade instructions - Remote

6A5E33338888-AG, 06/2016

⑤

Connect the display cable, and leave the display unattached as shown in photo.

⑥

Return power to the device.

Replace DSL cassette

①

Unscrew the locking screw of the blind lid and remove it using a wrench key if necessary.

②

Release the rubber band by lifting it off the small hook next to the cable plug.

③Disconnect the cable plug as shown in the photo.

FC430 upgrade instructions - Remote

A5E33338888-AG, 06/2016 7

④

Remove the screw that holds the DSL cassette.

⑤Carefully remove DSL cassette from housing.

⑥Remove the connector and mount the one supplied with the new DSL cassette.

Note: Make sure to connect the wires as shown in the next table.

Terminal number

Description

Wire color (Siemens cable)

24 V DC

Orange

0 V

Yellow

White

Blue

FC430 upgrade instructions - Remote

8A5E33338888-AG, 06/2016

Install new DSL cassette

①

Insert the new DSL cassette into housing.

②

Fasten the screw that holds the DSL and reconnect the cable with the new plug.

③

Fasten the rubber band to the hook.

④

Remove the O-ring from the lid.

⑤

Reinstate the lid until mechanical stop. Wind back the lid by one turn.

⑥

Mount O-ring by pulling it over the lid and tighten lid cover until you feel friction from the O-ring on both sides. Wind

lid further by one quarter of a turn to seal on the O-ring.

⑦

Reinstate and tighten lid lock screw.

Upgrade firmware

Follow these steps to upgrade the firmware using the local user display:

Note

Make sure to connect the transmitter and sen

sor before you update the firmware.

NOTICE

SensorFlash

Do NOT remove the SensorFlash during the update.

①

Insert the new SensorFlash delivered with the upgrade package into the transmitter.

②

On the display press from one of the measurement views. Sign in as "Expert" (default password 2834).

③

Go to menu item 3.1.10 "Firmware Revision", change the parameter to new FW version "2.02.02-01" and confirm by

pressing .

④Wait 2-3 minutes before the update starts. The update takes approximately 10 minutes and the transmitter makes a

restart after a successful update.

The display flashes and indicates progress during the update.

⑤

After the restart the display shows the wizard "First startup" .The firmware update does not change the configuration,

but you must go through the basic parameters to confirm the settings (display language, date, time).

Select "No" when asked if you want to go through the Quick commissioning wizard.

Synchronize data

To complete the upgrade, the new sensor electronic must be synchronized with the original SensorFlash data.

①Remove power from the device.

Remove the SensorFlash from the transmitter and insert original one.

FC430 upgrade instructions - Remote

A5E33338888-AG, 06/2016 9

②

Return power to the device.

Alarm 151 "Sensor serial number mismatch" will appear in the display. SensorFlash backup is not possible due to

serial number mismatch between sensor front-end and SensorFlash. Sensor flash data, for example backup data for

sensor calibration, from the replaced sensor electronic must be copied from the SensorFlash to the new electronic.

Proceed as follows to synchronize the data and clear alarm 151.

③Sign in as "Expert" (default password 2834).

Go to menu item 3.3.7.2.1 "Replace Sensor Cassette (Remote)" and press . Select "OK" and press to start

the synchronization.

Synchronization updates data between SensorFlash and sensor electronic. Alarm 151 disappears and all

parameters are backed up in the SensorFlash.

④Verify the data synchronization: Go to menu item 3.1.14.4 "Serial number" (sensor), and ensure that the number

matches the sensor serial number on the sensor product label.

Note: If alarm 151 "Sensor serial number mismatch" appears, then repeat steps 3-4.

Note

Update PID parameters

For update of PID parameters, see FAQ (

https://support.industry.siemens.com/cs/ww/en/view/109738556).

Fraction variant

New fraction configurations are made available in the new firmware. The following step must be performed for fraction

configured flowmeters:

①Go to menu item 2.2.7.3 "Active Fraction" and press . From the list, select the fraction used in the application,

and press .

Note: If the ordered fraction is not found on the list, then select the last option "Empty".

Reinstate display and display lid

①

Reconnect display cable and carefully push display back into housing.

②

Remove the O-ring from the lid.

③

Reinstate the display lid until mechanical stop. Wind back the lid by one turn.

④

Mount the O-ring by pulling it over the display lid; then turn the lid until you feel friction from the O-ring on both sides.

FC430 upgrade instructions - Remote

10 A5E33338888-AG, 06/2016

⑤

Wind the display lid by one quarter of a turn to seal on the O-ring and tighten the fixing screw.

FC430 upgrade instructions - Remote

A5E33338888

, 06/2016

Siemens AG

Division Process Industries and Drives

Postfach 48 48

90026 NÜRNBERG

GERMANY

Andere Handbücher für SITRANS FC430

Inhaltsverzeichnis

Sprachen:

Andere Siemens Messgerät Handbücher

Siemens

Siemens SENTRON PAC2200CLP Bedienungsanleitung

Siemens

Siemens SOMATOM Sensation Cardiac Version A60 Benutzerhandbuch

Siemens

Siemens SITRANS F Betriebsanleitung

Siemens

Siemens SITRANS DA400 Bedienungsanleitung

Siemens

Siemens Set CEM CERT Bedienungsanleitung

Siemens

Siemens ABHW-4BZ Bedienungsanleitung

Siemens

Siemens SITRANS F M MAGFLO Bedienungsanleitung

Siemens

Siemens SITRANS F FCS400 Bedienungsanleitung

Siemens

Siemens SITRANS F Bedienungsanleitung

Siemens

Siemens SIMEAS R-PMU Bedienungsanleitung

Siemens

Siemens SITRANS TDL Bedienungsanleitung

Siemens

Siemens Milltronics C-40 Bedienungsanleitung

Siemens

Siemens 5SV8000-6KK Bedienungsanleitung

Siemens

Siemens SITRANS F M MAG 3100 Bedienungsanleitung

Siemens

Siemens Veeder-Root Driver Bedienungsanleitung

Siemens

Siemens SIPROCESS GA700 Bedienungsanleitung

Siemens

Siemens SITRANS F M MAG 8000 Bedienungsanleitung

Siemens

Siemens SITRANS F US SONO 3300 Bedienungsanleitung

Siemens

Siemens Sitrans F Series Bedienungsanleitung

Siemens

Siemens SICAM Bedienungsanleitung

Siemens

Siemens SITRANS F US SONOFLO Bedienungsanleitung

Siemens

Siemens 13-xx-ST-SBT Series Bedienungsanleitung

Siemens

Siemens SENTRON PAC2200 Bedienungsanleitung

Siemens

Siemens SIMATIC ST-1500 Stücklistenhandbuch

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung

Konica Minolta

Konica Minolta BC-10 Plus Bedienungsanleitung