Siemens SIREMOBIL Iso-C Betriebsanleitung

SIREMOBIL Iso-C

English

Print No.: SPR2-230.076.01.01.02 Doc. Gen. Date: 02/99

Replaces: n.a.

The reproduction, transmission or

use of this document or its contents

is not permitted without express

written authority. Offenders will be

liable for damages. All rights,

including rights created by patent

grant or registration of a utility

model _or_design,_are_reserved.

Service Instructions

Replacing the horizontal lift brake

SIREMOBIL Iso-C SPR2-230.076.01 Page 2 of 16 Siemens AG

Rev. 01 02/99 TD SD 24 Medical Engineering

Replacing the horizontal lift brake1

General 1

Safety information 1

When performing service work and tests, adhere to the product-specific safety information

in the documents as well as the general safety information contained in Register 2 of the

TI folder.

Miscellaneous information 1

These instructions describe the replacement of the horizontal lift brake on the SIREMO-

BIL Iso-C.

Required parts 1

Required measurement and auxiliary devices

Required tools 1

•Standardservicekit

•1 set of Allen keys

•1Ratchet

•1 nutwitha 30mm socket

•Springscaleto 200N

Additional auxiliary devices 1

•Block of hardwood, approx. 80mm x 60mmx 60mm (Height x length x width)

•Work table approx. 850mm x 1800mm x 800mm (height xlength xwidth)with abearing

capacityof > 1200N.

2 worktables approx. 850mm x 1000mmx 600mm (height x length xwidth)witha

bearingcapacityof>600N.

•Magneticbrake (Item number: refer to the SIREMOBIL Iso-C spare parts

list)

•Protectiveconductormeter 44 15 899 RV090

•BenderSafetytester 97 06 979 Y0526

•Loctite648 20 48 601

Replacing the horizontal lift brake 3

Siemens AG SPR2-230.076.01 Page 3 of 16 SIREMOBIL Iso-C

Medical Engineering Rev. 01 02/99 TD SD 24

Preliminary steps 1

•ConnecttheSIREMOBILIso-Cto power .

•Positionthewoodenblock (1/Fig.1)underneath.

•Move theC-arm into the horizontal position (Fig. 1).

•PositiontheC-armover the work table.

•Slowly move theliftingcolumndown inincrements until the C-arm is positioned just flat

on the table.When doing this, make sure that the worktable is centered around the C-

arm and thatas much of the railing as possible is lying on the table.

Disassembly 1

•SwitchOFF the SIREMOBILIso-C.

•Removethe docking plate for the MODULARIS,ifitisconnected.

•Removethe cover with the brake switches (2/Fig.1)(screwsareonthe underside).

When doing this,remove the ground cable and disconnect the connection to the switch

board.

Push the wooden block under the SIREMOBIL frame prior to removing

the C-arm for service. Otherwise, the frame may tip over when the C-arm

is removed from the lifting column.

When placing the C-arm on the table, lower the lifting column only far

enough until the C-arm is positioned flat on the table with the entire rail-

ing.

Fig. 1

Fig. 1 shows one possible arrangement using 2 smaller work tables.

CAUTION

NOTICE

SIREMOBIL Iso-C SPR2-230.076.01 Page 4 of 16 Siemens AG

Rev. 01 02/99 TD SD 24 Medical Engineering

4 Replacing the horizontal lift brake

•Remove the lower cover (1/Fig. 2). Loosen the screws only (2/Fig.2), but do not remove

them.

•Remove the back cover (3/Fig. 2) (Velcro closure).

•Removethe upper cover plate (1/Fig.3).Also remove thecabletiesand the fastener

clamps(2/Fig.3)

•Remove the back cover (1/Fig. 4).

•Removethe guide bearings(1/Fig.5).

•Removeplug connectionsX22 and X23 (2/Fig.5).

•Removethe cable clamps (3/Fig.5).

•Removethecable guide (4/Fig.5).

Fig. 2 Fig. 3

Fig. 4 Fig. 5

S3 S4

Replacing the horizontal lift brake 5

Siemens AG SPR2-230.076.01 Page 5 of 16 SIREMOBIL Iso-C

Medical Engineering Rev. 01 02/99 TD SD 24

•Removethe cable clamp (1/Fig.6).

•Removethe cable clamp (2/Fig.6)and remove thecableties(2/Fig.6).

•Removethe cable ties around thecablebundle(5/Fig.5).

•Remove the cover plates (1/Fig.7).

•Removethe nut (1/Fig.8).(30mmsocket)

•Remove the threeAllen screws (2/Fig.8) andremove theangulation brake completely.

Whendoing this,make sure tohold onto the 3 screwsof the angulation brake oruse

adhesivetapetopreventthemfromfalling.Fig.9 shows the completeangulationbrake.

Fig. 6 Fig. 7

Fig. 8 Fig. 9

SIREMOBIL Iso-C SPR2-230.076.01 Page 6 of 16 Siemens AG

Rev. 01 02/99 TD SD 24 Medical Engineering

6 Replacing the horizontal lift brake

•Removethe screws for the end stop(1/Fig.10).

•Connectthecablestoboth microswitches(refertoS3,S4/Fig.3andFig.11).

•ReconnectX23.

•Place the coverwith the brake switcheson theC-arm andplug inthe test board.

•SwitchON the SIREMOBIL.

•Release the horizontal lift brake(press the switch, the LED lights).

•Move the vertical lifting column up anddown until you areable to hammertheendstop

(1/Fig.10) out of thehorizontal carriage in the direction of the arrows (arrows/Fig.10)

withoutapplyingpressure to the shaft.

•Once the end stop has been removed, the shaft should lie horizontal within the

horizontal carriage and shouldnot be pressing against it.

•SwitchOFF the SIREMOBIL.

Fig. 10 Fig. 11

S3.2

S3.NL

S3.Comm S4.Comm

S4.N

S4.2

Replacing the horizontal lift brake 7

Siemens AG SPR2-230.076.01 Page 7 of 16 SIREMOBIL Iso-C

Medical Engineering Rev. 01 02/99 TD SD 24

•Removethe spring ring (1/Fig.12).

•Removethe stopwheel (1/Fig.12).

•Removetheend stop(1/Fig.13).

•Removethe spring ring (2/Fig.13).

Fig. 12 Fig. 13

SIREMOBIL Iso-C SPR2-230.076.01 Page 8 of 16 Siemens AG

Rev. 01 02/99 TD SD 24 Medical Engineering

8 Replacing the horizontal lift brake

•SwitchON the SIREMOBILIso-Cand releasethehorizontalbrake(theLED in the

switchlights).

•Move the horizontal carriage so that the opening in the horizontal carriage,

(1/Fig.14)as shownin Fig.14is located oppositethe opening in thebearingsupport(2/

Fig.14).

•Insert the cable bundle(3/Fig.14) betweenthe horizontal carriageand the bearing

supportin the direction of the C-arm. When doing this, be careful not to damage or crimp

thecables!

•Subsequentlymovethehorizontalcarriagecarefully forwardoutofthebearing support

until thehorizontal lift brake (1/Fig.15)with the plate(2/Fig.15) is accessible.

•Notethefollowing:

- Becarefulnottocrimpordamage thecables.

- The C-arm must remaincentered onthe work table. Move the work table, if necessary.

- Securethecoverwiththeswitchestopreventitfromfalling.

- When removing the horizontal carriage,keep it centered to the ballbearings. Do not tilt

it.

- You may have to adjustthe position of the vertical lifting column until the horizontal

carriagemoveseasily.

•SwitchOFF the SIREMOBIL Iso-C.

•Disconnecttheplugconnectionsforthehorizontalbrake.

•Removethe plate (2/Fig.15).

•Remove the horizontal brake cable from the plate and lift the horizontal brakeout of the

bearingsupport.

Fig. 14 Fig. 15

Two persons are required to remove the horizontal carriage. One person

should be at the bearing surface of the C-arm. The second person at the

horizontal carriage.

When removing the horizontal carriage, make sure that none of the

cables is crimped or damaged.

NOTICE

Replacing the horizontal lift brake 9

Siemens AG SPR2-230.076.01 Page 9 of 16 SIREMOBIL Iso-C

Medical Engineering Rev. 01 02/99 TD SD 24

Installation 1

•Lift thehorizontal brake out ofthe bearing support. Reserve the two springs (2/Fig.16).

•Remove both screwsfrom theold horizontal brake (1/Fig. 16) and install them on the

newhorizontalbrake.

•Placethenew horizontalbrakein the bearing support.The two screwsshouldnotstick

inthe slots.(Checkthisby pressing down on the horizontalbrake).Youmay have to

take outthe horizontal brake again and slightly bend the screws to the side (hit the screw

headlightlyon the side)

•Routethe horizontalbrakecablebackthroughtheplate(1/Fig.17).The cable must be

positioned in the recess(1/Fig.18, 1/Fig.19).

•Routethe cable end of thehorizontalbrakeparallelto the cable bundle inthe horizontal

carriage.

Fig. 16 Fig. 17

Fig. 18 Fig. 19

SIREMOBIL Iso-C SPR2-230.076.01 Page 10 of 16 Siemens AG

Rev. 01 02/99 TD SD 24 Medical Engineering

10 Replacing the horizontal lift brake

•Reattachtheplate(1/Fig.17)withthescrews.

•Clean thebraking surface of the horizontal brake (2/Fig.17).(Dirt and metal particles)

•Reattachthehorizontalbrake.

•SwitchON the Siremobiland releasethehorizontalbrake.

•Insert the horizontalcarriage back in the bearing support.

•Notethefollowing:

- Becarefulnottocrimpordamage thecables.

- Becarefulofthehorizontalbrakecable.RefertoFig.18and19.

- The C-arm must remaincentered onthe work table. Move the work table, if necessary.

- Securethecoverwiththeswitchestopreventitfromfalling.

- Wheninsertingthehorizontalcarriage, keepitcenteredtothe ball bearings.

- You may have to adjustthe position of the vertical lifting column until the horizontal

carriagemoveseasily.

Andere Handbücher für SIREMOBIL Iso-C

Inhaltsverzeichnis

Andere Siemens Medizinische Geräte Handbücher

Siemens

Siemens ARCADIS Varic Installationshandbuch

Siemens

Siemens Uroskop ACCESS Bedienungsanleitung

Siemens

Siemens AXIOM Iconos R200 Bedienungsanleitung

Siemens

Siemens MAGNETOM Skyra fit Bedienungsanleitung

Siemens

Siemens Healthineers UniPOC RAPIDPoint 500 Bedienungsanleitung

Siemens

Siemens Hematek 3000 System Bedienungsanleitung

Siemens

Siemens ACUSON X150 Bedienungs- und Wartungsanleitung

Siemens

Siemens MODULARIS Uro Plus Montageanleitung

Siemens

Siemens MammoReport Plus Technische Daten

Siemens

Siemens LITHOSTAR Multiline Bedienungsanleitung

Siemens

Siemens MAMMOMAT NovationDR Bedienungsanleitung

Siemens

Siemens POLYMOBIL Plus Bedienungs- und Wartungsanleitung

Siemens

Siemens LITHOSTAR Multiline Leitfaden

Siemens

Siemens SIREMOBIL Compact L Betriebsanleitung

Siemens

Siemens ARCADIS Varic Installationshandbuch

Siemens

Siemens ACUSON Freestyle Bedienungsanleitung

Siemens

Siemens MAMMOMAT 1000 Nova Handbuch

Siemens

Siemens MOBILETT Plus Betriebsanleitung

Siemens

Siemens SIREMOBIL Compact Gebrauchsanweisung

Siemens

Siemens SOMATOM Bedienungsanleitung

Siemens

Siemens MAMMOMAT 300 Anleitungen und Rezepte

Siemens

Siemens Servo Screen 390 Bedienungsanleitung

Siemens

Siemens MTCO 1324 Bedienungsanleitung

Siemens

Siemens Drager Medical Fabius GS Montageanleitung

Beliebte Medizinische Geräte Handbücher anderer Marken

TekTone

TekTone Tek-CARE160 Bedienungsanleitung

NeuroMetrix

NeuroMetrix Quell 2.0 Bedienungsanleitung

AMT

AMT XLR8 Bedienungsanleitung

EDAN

EDAN SONOTRAX Pro Bedienungsanleitung

Restorative Therapies

Restorative Therapies RT300 Bedienungsanleitung

Gendex

Gendex Expert DC Bedienungsanleitung

Dexcowin

Dexcowin ADX4000W Bedienungsanleitung

Libelium

Libelium MySignals Bedienungsanleitung

Acelity

Acelity V.A.C.ULTA 4 Bedienungsanleitung

Caputron

Caputron ActivaDose II tDCS Bedienungsanleitung

Plinth 2000

Plinth 2000 93CDT Bedienungsanleitung

GE SENOGRAPHE 800T Bedienungsanleitung

GE Definium 5000 Bedienungsanleitung

Kanmed

Kanmed GE-1380 Bedienungsanleitung

Huntleigh

Huntleigh FD1 Bedienungsanleitung

Stryker

Stryker SPR Plus Bedienungsanleitung

Tobii Dynavox

Tobii Dynavox I-Series Bedienungsanleitung

S-Capepod

S-Capepod Evac Cocoon Bedienungsanleitung