Siemens Healthineers UniPOC RAPIDPoint 500 Bedienungsanleitung

Configuration Guide

RAPIDPoint 500

RAPIDPoint 500e

from software version 1.6

RAPIDPoint 500/RAPIDPoint 500e Configuration Guide 11555620, Rev. A, 2020-09 Page 2/8

RAPIDPoint 500/RAPIDPoint 500e Configuration Guide

No part of this manual or the products it describes may be reproduced by any means or in any form without

prior consent in writing from Siemens Healthcare Diagnostics.

UniPOC is a trademark of Siemens Healthcare Diagnostics, Inc.

All other trademarks are the property of their respective owners.

The information in this manual was correct at the time of printing. However, Siemens Healthcare Diagnostics

continues to improve products and reserves the right to change specifications, equipment, and maintenance

procedures at any time without notice.

If the UniPOC™ system is used in a manner differently than specified by Siemens Healthcare Diagnostics,

the protection provided by the equipment may be impaired. Observe warning and hazard statements.

RAPIDPoint 500/RAPIDPoint 500e Configuration Guide 11555620, Rev. A, 2020-09 Page 3/8

RAPIDPoint 500/RAPIDPoint 500e Configuration Guide

Table of Contents

1Introduction............................................................................................................................................ 4

2Intended Use ......................................................................................................................................... 4

3Instrument Configuration Pages............................................................................................................ 4

4Configuration Screens........................................................................................................................... 5

4.1 Download Options ......................................................................................................................... 6

4.2 Instrument Settings........................................................................................................................ 7

5Support .................................................................................................................................................. 8

RAPIDPoint 500/RAPIDPoint 500e Configuration Guide 11555620, Rev. A, 2020-09 Page 4/8

RAPIDPoint 500/RAPIDPoint 500e Configuration Guide

1 Introduction

This manual describes the use of the UniPOC™Point of Care Data Management System software to

configure the RAPIDPoint®500 and RAPIDPoint®500e device.

Please read this configuration guide for step-by-step instructions and illustrations on how to configure the

devices prior to placing them in service.

2 Intended Use

This software allows you to configure and use the RAPIDPoint®500/RAPIDPoint®500e device with the

UniPOC™Point of Care Data Management System. This product is not for diagnostic use.

3 Instrument Configuration Pages

Important: Configuration settings can change based on the UniPOC application version and device driver

pack versions installed. For example, a device driver pack may be updated to support a new or changed

configuration setting but if you are using an older version of the UniPOC application that does not support

the change, you will not see the updated configuration setting in the UI.

The following Instrument Configuration pages are described in this manual.

•Download Options

•Instrument Settings

RAPIDPoint 500/RAPIDPoint 500e Configuration Guide 11555620, Rev. A, 2020-09 Page 5/8

RAPIDPoint 500/RAPIDPoint 500e Configuration Guide

4 Configuration Screens

The Instrument Configuration screens in UniPOC allow you to view and edit the RAPIDPoint 500 and

RAPIDPoint 500e configuration data for a specific location. These devices can be configured for the entire

Organization or for an individual Facility, Department or Location.

Note: Siemens recommends entering configuration data at the Facility level when possible. Department

level settings should then be used to vary the instrument configurations only as needed. The Organization

level settings then remain available for reference as default values.

Procedure:

Select a Facility, Department or Location in the tree.

From the menu, select Instruments > Configuration.

The Instrument Configuration screen appears.

Select RAPIDPoint 500 from the Instrument drop-down list.

Select one of the following Configuration Download options:

Assigned Location (Recommended) If you select this option, UniPOC uses the Location

where the device’s serial number or name resides in the Location Tree

regardless of where the device is used or docked (Default). This location

will determine the:

•Configuration settings to be downloaded to the device

•Supported lists downloaded to the device

•Location where all test data are uploaded to in the Tree

Download Location (Not Recommended) If you select this option, UniPOC uses the Location

where the device’s or docking station’s IP address resides in the Location

Tree. This location will determine the:

•Configuration settings to be downloaded to the device

•Supported lists downloaded to the device

•Location where all test data are uploaded to in the Tree

Note: UniPOC will automatically update the device’s location in the Tree

when it communicates to UniPOC.

Select the desired configuration tab and set the options.

Note: Be sure to note the selected Tree level prior to saving the instrument configuration

settings to ensure the settings are applied to the appropriate locations.

Do one of the following:

•Click the Save Configuration button to save the settings.

This will break the Parent-Child relationship and save the configuration as a new one, even

if no changes were made. Saving an instrument configuration for a lower level of the Tree

(Department or Location) will sever the relationship between the child and its parent level on

RAPIDPoint 500/RAPIDPoint 500e Configuration Guide 11555620, Rev. A, 2020-09 Page 6/8

RAPIDPoint 500/RAPIDPoint 500e Configuration Guide

the Tree. Breaking the Parent-Child relationship is necessary to enable configuration settings

different from the global Organization or Facility.

Refer to the UniPOC User’s Manual for more information about the Location Tree Parent-

Child Relationship.

•Click the Restore Default Configuration button to re-establish a Parent-Child relationship

that was severed in error or when the configuration settings should be the same as its parent

(Facility, Department or Location). This action will save the configuration from the parent.

•To cancel the configuration action without saving, go to a screen other than the Instrument

Configuration screen.

4.1 Download Options

When a device is placed into operation for the first time, all data that can be downloaded from UniPOC to

the model are automatically activated from this screen. This tab is used to set the download options. When

you enable a download, all pre-existing data of that type stored on the device will be overwritten. Once

enabled, options can be disabled at any time.

Note: When a selected download option is disabled, any previously downloaded data of that download type

will be removed from the device when the device receives its new configuration.

Explanation of the parameters

Enable download of the following

data:

Device users If selected, device users’ data will be downloaded.

Table 1: Downloads Options

RAPIDPoint 500/RAPIDPoint 500e Configuration Guide 11555620, Rev. A, 2020-09 Page 7/8

RAPIDPoint 500/RAPIDPoint 500e Configuration Guide

4.2 Instrument Settings

Each operator is assigned to a home Location within a Facility. Each Facility in the organization maintains

a separate operator list. Instrument settings saved at the Facility level affect the Department and Location

levels as well. Settings saved at the Location level affect only the selected Location.

Note: Instrument settings saved at the top level of the Tree affect all sub-levels.

Explanation of the parameters

Operator list location Choose from four location options to download the operator list.

Location

Facility The operator list will be downloaded to all instruments within the Facility. The

list will contain all operators certified for the device whose home location is

within the Facility.

Department The operator list will be downloaded to all instruments assigned to location

within the associated Department. The list will contain all operators certified for

the instrument whose home location is within the Department.

Location The operator list will be downloaded to all instruments assigned to a location.

The list will contain all operators certified for the instrument with a matching

home location.

None The operator list will not be downloaded. (Default)

Table 2: Instrument Settings

RAPIDPoint 500/RAPIDPoint 500e Configuration Guide 11555620, Rev. A, 2020-09 Page 8/8

RAPIDPoint 500/RAPIDPoint 500e Configuration Guide

5 Support

Contacting Siemens Support

Siemens is committed to helping you resolve any problems with the UniPOC™ Point of Care Data

Management System.

For assistance, contact POC Informatics Customer Service:

https://www.siemens-healthineers.com/point-of-care-testing/featured-topics-in-poct/informatics-featured-

topics/poc-informatics-customer-service-contacts

UniPOC_ConfigurationGuide_RP500_EN.docx

Template Used: 99e_UniPOC_ConfigurationGuide.dotx

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Siemens Medizinische Geräte Handbücher

Siemens

Siemens Hematek 3000 System Bedienungsanleitung

Siemens

Siemens MAMMOMAT 1000 Nova Anleitungen und Rezepte

Siemens

Siemens MAGNETOM syngo MR D11 Bedienungsanleitung

Siemens

Siemens ARCADIS Varic Bedienungsanleitung

Siemens

Siemens ADVIA 2400 Handbuch

Siemens

Siemens MAMMOMAT 300 Einrichtungshandbuch

Siemens

Siemens HearCheck Screener Bedienungsanleitung

Siemens

Siemens MAMMOMAT 3000 Einrichtungshandbuch

Siemens

Siemens VB 13C Bedienungsanleitung

Siemens

Siemens SIRECUST 1280 Bedienungsanleitung

Siemens

Siemens Healthineers MAGNETOM Sempra Bedienungsanleitung

Siemens

Siemens MAMMOMAT 300 Anleitungen und Rezepte

Siemens

Siemens AXIOM Iconos R200 Bedienungsanleitung

Siemens

Siemens MAMMOMAT Novation DR Installationshandbuch

Siemens

Siemens ARCADIS Installationshandbuch

Siemens

Siemens ACUSON Cypress Bedienungsanleitung

Siemens

Siemens Rapidlab 1200 Handbuch

Siemens

Siemens Sonoline G20 Bedienungsanleitung

Siemens

Siemens POLYMOBIL Plus Installationshandbuch

Siemens

Siemens POWERMOBIL Gebrauchsanweisung

Siemens

Siemens syngo MR E11 Bedienungsanleitung

Siemens

Siemens SOMATOM Scope Bedienungsanleitung

Siemens

Siemens Immulite Homocysteine 2000 Bedienungsanleitung

Siemens

Siemens 25 Bedienungsanleitung

Beliebte Medizinische Geräte Handbücher anderer Marken

TekTone

TekTone Tek-CARE160 Bedienungsanleitung

NeuroMetrix

NeuroMetrix Quell 2.0 Bedienungsanleitung

AMT

AMT XLR8 Bedienungsanleitung

Medipost-Nutristoma

Medipost-Nutristoma MD300K2 Bedienungsanleitung

EDAN

EDAN SONOTRAX Pro Bedienungsanleitung

Restorative Therapies

Restorative Therapies RT300 Bedienungsanleitung

Gendex

Gendex Expert DC Bedienungsanleitung

Dexcowin

Dexcowin ADX4000W Bedienungsanleitung

Libelium

Libelium MySignals Bedienungsanleitung

Acelity

Acelity V.A.C.ULTA 4 Bedienungsanleitung

Caputron

Caputron ActivaDose II tDCS Bedienungsanleitung

FujiFilm

FujiFilm Sonart Betriebsanleitung

Plinth 2000

Plinth 2000 93CDT Bedienungsanleitung

GE SENOGRAPHE 800T Bedienungsanleitung

GE Definium 5000 Bedienungsanleitung

Kanmed

Kanmed GE-1380 Bedienungsanleitung

Huntleigh

Huntleigh FD1 Bedienungsanleitung

Stryker

Stryker SPR Plus Bedienungsanleitung