Siemens NCC-1F Bedienungsanleitung

P/N 315-095965-8

OPERATION

The Model NCC-1F from Siemens Industry,

Inc., provides the NCC-G computer with a

direct RS-485 connection to the SIEMENS

XNET, eliminating the requirement that the

NCC-G computer be located within 25 feet of

an NIM-1R/1W. The NCC-1F operates in both

Style 4 and Style 7 modes.

The module installs in the NCC-G computer

and requires an empty 16-Bit ISA slot. The

NCC-1F can be set to any standard PC COM

port address and interrupt.

CONFIGURATION

The NCC-1F comes from the factory config-

ured as COM 2. In most cases this does not

need to be changed. If COM 2 is not available,

Installation Instructions

Model NCC-1F

NCC-G XNET Interface

use Table 1 to select the desired COM port. Be

sure to configure the NCC-G computer to use the

same port and IRQ for XNET communications.

See Figure 1 for the location of the jumpers.

Figure 1

NCC-1F Module Board

TABLE 1

CONFIGURING THE NCC-1F

COM JP1 JP2 ADDRESS JP3 (IRQ)

1* A C 3F8-3FF 4

2* A D 2F8-2FF 3

3 B C 3E8-3EF 4

4 B D 2E8-2EF 3

* Be sure to disable the NCC-G computer's internal

COM port or hardware conflicts will result.

Siemens Industry, Inc.

Building Technologies Division

Florham Park, NJ

Siemens Building Technologies, Ltd.

Fire Safety & Security Products

2 Kenview Boulevard

Brampton, Ontario

L6T 5E4 Canada

The NCC-1F also provides IRQs 5, 7, 9, 10, 11,

12, 14, and 15. These can be used in conjunction

with COM 3 and COM 4 if IRQs 3 and 4 are used

by other hardware. When using these IRQs be

sure that no other hardware has been assigned

to the IRQ used on the NCC-1F.

INSTALLATION

Remove all NCC-G power before installation.

To install the NCC-1F follow the steps listed below:

1. Unscrew the two knurled knobs on the rear of

the NCC-G computer.

2. Slide the cover back an inch or so and lift it off.

3. The NCC-1F installs into any free 16-Bit

ISA slot in the NCC-G computer. Select a slot

and remove the blank cover, keeping

the screw.

4. Remove the terminal block from the NCC-1F

by removing the two screws that hold it to the

bracket.

5. Place the NCC-1F into the open slot so that

the NCC-1F card edge extends through the

opening in the back of the PC.

6. Align the NCC-1F with the card edge

connector in the NCC-G computer and

press it firmly into place.

7. Secure the NCC-1F by installing the screw

that held the blank cover. (Refer to Step 3.)

8. Replace the NCC-G computer cover and

tighten the knurled knobs.

9. Reattach the terminal block by sliding it

onto the NCC-1F card edge and install the

two screws. This is a keyed connection

and will only install one way.

ELECTRICAL CONNECTIONS

Network (XNET)

The XNET connections are made on terminals

1-4 of the terminal block on the rear of the

NCC-1F. The primary pair (or network A) is

on terminals 1 and 2. The secondary pair (or

network B) is on terminals 3 and 4.

For Style 4 networks, install a 120 ohm EOLR

on terminals 3 and 4. See Figure 2 for wiring

details.

For Style 7 networks, connect to both the

primary and secondary pairs. See Figure 2 for

wiring details.

Figure 2

NCC-1F XNET Connections

12345678

910111213141516

17 18 19 20 21 22 23 24

SEE NOTE 7 DO NOT USE

DO NOT USE

DO NOT USE DO NOT USE

ONE SLOT OF CC-5

NIC-C

123456

PAIR A

SUPERVISED

POWER LIMITED

PAIR B

(OMIT FOR STYLE 4)

SUPERVISED

POWER LIMITED

LOCATED INSIDE NCC

NOTE:

IF THE NCC IS LOCATED

AT THE END OF THE XNET

NETWORK, INSTALL EOLR

P/N 140-820350 ACROSS

TERMINALS1&2AND3&4.

NCC-1F

MOM-4

TB3 OR TB4

NIM-1R / NIM-1W

1234

TO ADDITIONAL

NIM-1Rs, NIM-1Ws,

NCC-1Fs OR NIC-Cs

NOTES:

1. No EOLR required for NIC-C.

2. 18 AWG min., 12 AWG max.

3. 80 Ohms max. per pair.

Unshielded twisted pair - .5μF line to line

Shielded twisted pair - .3μF line to line, .4μF line to

shield

4. Use twisted pair or twisted shielded pair.

5. Terminate shields at one end only.

6. Power limited to NFPA 70 per NEC 760.

7. CC-5 terminals 9 - 14 are not connected and can be

used to tie shields together.

8. Maximum voltage 8V P-P.

9. Each pair independently supervised.

Refer to Wiring Specification for MXL, MXL-IQ

and MXLV Systems, P/N 315-092772 revision

6 or higher, for additional wiring information.

Shields

Shields for the XNET must be connected at ONE

and ONLY ONE end of the network. If you wish

to terminate the shields at the NCC-G computer,

use terminal 5 on the NCC-1F. See Figure 2.

Earth Ground

A good earth ground must be provided for proper

transient protection of the NCC-1F and the

NCC-G computer. Connect a separate ground to

terminal 6 on the NCC-1F (Refer to Figure 2).

Ground Fault Detection

The NCC-1F provides electrical isolation be-

tween the NCC-G computer and the XNET. This

allows for ground fault detection to be enabled on

the XNET. Ground fault detection is only possible

if ALL NCC-G computers in the system are

connected to XNET with an NCC-1F.

Ground fault detection must be enabled at a

NIM-1R/-1W or NIC-C. Select one and only one

NIM-1R/-1W or NIC-C in the system where the

ground fault is to be detected. You must locate

the NIM-1R/-1W in a cabinet with either an MMB,

SMB or a PSR-1. See Figure 3 for the wiring

diagram.

If the XNET is divided into multiple sections of

copper wire using fiber optic segments, ground

fault detection can be enabled at one NIM-1R/-1W

or NIC-C for each section of copper wire. Refer to

the NIC-C Installation Instructions, P/N 315-

033240 if you wish to use the NIC-C to provide

ground fault detection.

ELECTRICAL RATINGS

NCC-1F: 5 VDC @ 250mA

Network (XNET): 8V P-P, 190mA max

TB3

NIM-1R/-1W

IN TB4

NIM-1R/-1W

IN TB3

USE ONLY ONE

TB5

TB4

MOM-2

MOM-4

TB7 TB4

13 14 15 16

91011 12

13 14 15 16

5678

2234

Figure 3

Wiring for Ground Fault Detection

P/N 315-095965-8

Siemens Industry, Inc.

Building Technologies Division

Florham Park, NJ

Siemens Building Technologies, Ltd.

Fire Safety & Security Products

2 Kenview Boulevard

Brampton, Ontario

L6T 5E4 Canada

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Siemens Aufnahmegeräte Handbücher

Siemens

Siemens NIC-C Bedienungsanleitung

Siemens

Siemens 2D-TZ577 Bedienungsanleitung

Siemens

Siemens CM 1542-5 Bedienungsanleitung

Siemens

Siemens VDO DTCO 1381 Stücklistenhandbuch

Siemens

Siemens VIU-20 Bedienungsanleitung

Siemens

Siemens IM 152 Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens PS-5N7 Bedienungsanleitung

Siemens

Siemens IAQ6-1 Bedienungsanleitung

Siemens

Siemens RUGGEDCOM RMC30 Bedienungsanleitung

Siemens

Siemens SIMATIC NET CP 5613 Bedienungsanleitung

Siemens

Siemens 6AT8000-1BB00-0XA0 Bedienungsanleitung

Siemens

Siemens SIMATIC RTLS4040T Bedienungsanleitung

Siemens

Siemens 5WG1 220-2DB31 Service-Handbuch

Siemens

Siemens RNI Bedienungsanleitung

Siemens

Siemens Apogee P1 Bedienungsanleitung

Siemens

Siemens SIPLUS CMS4000 ION BINARYINPUT T001 Bedienungsanleitung

Siemens

Siemens XTRI-S Bedienungsanleitung

Siemens

Siemens Albatros2 RVA78.690 Bedienungsanleitung

Siemens

Siemens SIMATIC Distributed I/O System DP/ASi Link Bedienungsanleitung

Siemens

Siemens 538-735 Bedienungsanleitung

Siemens

Siemens GAMMA instabus 5WG1 220-2AB21 Service-Handbuch

Siemens

Siemens SIMATIC HMI KP400 Comfort Bedienungsanleitung

Siemens

Siemens TC35 Benutzerhandbuch

Beliebte Aufnahmegeräte Handbücher anderer Marken

KV2 Audio

KV2 Audio 500 Series Bedienungsanleitung

Robotics Technologies

Robotics Technologies microBus-Cam II Bedienungsanleitung

Seca

Seca 460 Bedienungsanleitung

Cognex

Cognex MVS-8000 Series Bedienungsanleitung

Mect

Mect MPNC006 Series Bedienungsanleitung

Bad Caf

Bad Caf THE LEASH Bedienungsanleitung

Strymon

Strymon NIGHTSKY Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung

Tews Technologies

Tews Technologies TPMC465 Bedienungsanleitung

Honeywell

Honeywell Excel 50 Bedienungsanleitung

SeaLevel

SeaLevel COMM+8.LPCI Bedienungsanleitung

Arturia

Arturia AUDIOFUSE STUDIO Bedienungsanleitung

Rukra

Rukra RK-1240 Bedienungsanleitung

Samson

Samson SCOM Bedienungsanleitung

Dynacord

Dynacord DPS260 Bedienungsanleitung

Pyle Pro

Pyle Pro PSS8 Bedienungsanleitung

Nice

Nice Core Bedienungsanleitung

RF-System

RF-System TinyGate Gebrauchs- und Pflegehandbuch