SIGMA TEK AM 222 Bedienungsanleitung

AM 222

S-DIAS Analog Mixed Module

Instruction Manual

Date of creation: 20.03.2015

Version date: 22.11.2023

Article number: 20-017-222-E

Publisher: SIGMATEK GmbH & Co KG

A-5112 Lamprechtshausen

Tel.: +43/6274/4321

Fax: +43/6274/4321-18

Email: [email protected]

WWW.SIGMATEK-AUTOMATION.COM

SIGMATEK GmbH & Co KG

Translation of the Original Instructions

tributed in any form (print, photocopy, microfilm or in any other process) without the express permission.

We reserve the right to make changes in the content without notice. The SIGMATEK GmbH & Co KG is not responsi-

ble for technical or printing errors in the handbook and assumes no responsibility for damages that occur through

use of this handbook.

S-DIAS ANALOG MIXED MODULE AM 222

22.11.2023 Page 1

S-DIAS Analog Mixed Module AM 222

with 2 current inputs

2 current outputs

The S-DIAS AM 222 analog mixed module has two current inputs,

0-20 mA and 4-20 mA respectively, each with a 16-bit resolution as

well as two current outputs, 0-20 mA and 4-20 mA respectively, with a

12-bit resolution. The voltage supply for the current inputs and out-

puts are monitored for under voltage.

AM 222 S-DIAS ANALOG MIXED MODULE 
 
Page 2 22.11.2023 
Contents 
Introduction............................................................................. 5 
1 Target Group/Purpose of this Operating Manual ......................5 
2 Important Reference Documentation .........................................5 
3 Contents of Delivery.....................................................................5 
2Basic Safety Directives .......................................................... 6 
1 Symbols Used...............................................................................6 
2 Disclaimer......................................................................................8 
3 General Safety Directives ............................................................9 
4 Software/Training .......................................................................10 
3Standards and Directives......................................................11 
1 Directives.....................................................................................11 
1.1 EU Conformity Declaration................................................................11 
4Type Plate...............................................................................12
5Technical Data .......................................................................13 
1 Analog Input Specifications ......................................................13 
2 Analog Output Specifications ...................................................14 
3 Analog In and Output Voltage Supply Specifications ............14 
4 Voltage Monitor External +24 V Supply....................................14 
5 Electrical Requirements.............................................................15 
6 Miscellaneous .............................................................................16 
7 Environmental Conditions.........................................................16 

 S-DIAS ANALOG MIXED MODULE AM 222 
 
11.2023 Page 3 
6Mechanical Dimensions........................................................17 
7Connector Layout..................................................................18 
1 Status LEDs.................................................................................19 
2 Applicable Connectors...............................................................19 
3 Label Field ...................................................................................20 
8Wiring.....................................................................................21 
1 Wiring Example...........................................................................21 
2 Note..............................................................................................22 
3 Signal Source connection..........................................................23 
4 Load Connection.........................................................................23 
9Assembly/Installation ...........................................................24 
1 Check Contents of Delivery.......................................................24 
2 Mounting......................................................................................25 
Addressing.............................................................................27 
1 Address Mapping Overview.......................................................27 
Supported Cycle Times ........................................................29 
1 Cycle Times below 1 ms (in µs).................................................29 
2 Cycle Times equal to or above 1 ms (in ms)............................29 
Transport/Storage.................................................................30 
Storage...................................................................................30 

AM 222 S-DIAS ANALOG MIXED MODULE 
 
Page 4 22.11.2023 
Maintenance...........................................................................31 
1 Service.........................................................................................31 
2 Repair...........................................................................................31 
Disposal..................................................................................31
Hardware Class AM222 .........................................................32
1 General.........................................................................................33 
2 Analog Inputs and Outputs........................................................34 
3 Cable Break Detection and Measurement Values...................35 
4 Communication Interfaces.........................................................35 
 

S-DIAS ANALOG MIXED MODULE AM 222

22.11.2023 Page 5

1. Introduction

1.1 Target Group/Purpose of this Operating Manual

This operating manual contains all information required for the operation of the product.

This operating manual is intended for:

•Project planners

•Technicians

•Commissioning engineers

•Machine operators

•Maintenance/test technicians

General knowledge of automation technology is required.

Further help and training information, as well as the appropriate accessories can be found

on our website www.sigmatek-automation.com.

Our support team is happily available to answer your questions.

Please see our website for our hotline number and business hours.

1.2 Important Reference Documentation

This and additional documents can be downloaded from our website or obtained through

support.

1.3 Contents of Delivery

1x AM 222

AM 222 S-DIAS ANALOG MIXED MODULE

Page 6 22.11.2023

2 Basic Safety Directives

2.1 Symbols Used

The following symbols are used in the operator documentation for warning and danger

messages, as well as informational notes:

DANGER

Danger indicates that death or serious injury will occur, if the speci-

fied measures are not taken.

To avoid death or serious injuries, observe all guidelines.

Danger indique une situation dangereuse qui, faute de prendre les

mesures adéquates, entraînera des blessures graves, voire mortelles.

Respectez toutes les consignes pour éviter des blessures

graves, voire mortelles.

WARNING

Warning indicates that death or serious injury can occur, if the speci-

fied measures are not taken.

To avoid death or serious injuries, observe all guidelines.

Avertissement d’une situation dangereuse qui, faute de prendre les

mesures adéquates, entraînera des blessures graves, voire mortelles.

Respectez toutes les consignes pour éviter des blessures

graves, voire mortelles.

CAUTION

Caution indicates that moderate to slight injury can occur, if the speci-

fied measures are not taken.

To avoid moderate to slight injuries, observe all guidelines.

Attention indique une situation dangereuse qui, faute de prendre les

mesures adéquates, peut entraîner des blessures assez graves ou

légères.

Respectez toutes les consignes pour éviter des blessures

graves, voire mortelles.

S-DIAS ANALOG MIXED MODULE AM 222

22.11.2023 Page 7

INFORMATION

Information

Provides important information on the product, handling or

relevant sections of the documentation, which require atten-

tion.

AM 222 S-DIAS ANALOG MIXED MODULE

Page 8 22.11.2023

2.2 Disclaimer

INFORMATION

The contents of this operating manual were prepared with the greatest

care. However, deviations cannot be ruled out. This operating manual

is regularly checked and required corrections are included in the sub-

sequent versions. The machine manufacturer is responsible for the

proper assembly, as well as device configuration. The machine opera-

tor is responsible for safe handling, as well as proper operation.

The current operating manual can be found on our website. If neces-

sary, contact our support.

Subject to technical changes, which improve the performance of the

devices. The following operating manual is purely a product descrip-

tion. It does not guarantee properties under the warranty.

Please thoroughly read the corresponding documents and this operat-

ing manual before handling a product.

SIGMATEK GmbH & Co KG is not liable for damages caused

through, non-compliance with these instructions or applicable

regulations.

Inhaltsverzeichnis

Andere SIGMA TEK Steuereinheit Handbücher

SIGMA TEK

SIGMA TEK CP 112 Bedienungsanleitung

SIGMA TEK

SIGMA TEK AI 022-1 Bedienungsanleitung

SIGMA TEK

SIGMA TEK KL 181 Bedienungsanleitung

SIGMA TEK

SIGMA TEK ISE 021 Bedienungsanleitung

SIGMA TEK

SIGMA TEK AI 0812 Bedienungsanleitung

SIGMA TEK

SIGMA TEK C-DIAS Bedienungsanleitung

SIGMA TEK

SIGMA TEK SRO 021 Bedienungsanleitung

SIGMA TEK

SIGMA TEK S-DIAS AI 022 Bedienungsanleitung

SIGMA TEK

SIGMA TEK CSDI 162 Bedienungsanleitung

SIGMA TEK

SIGMA TEK STO 081 Bedienungsanleitung

SIGMA TEK

SIGMA TEK SCP 111-2 Bedienungsanleitung

SIGMA TEK

SIGMA TEK SCP 111-S Bedienungsanleitung

SIGMA TEK

SIGMA TEK SCP 111 Bedienungsanleitung

SIGMA TEK

SIGMA TEK STO 081 Bedienungsanleitung

SIGMA TEK

SIGMA TEK DM 167 Bedienungsanleitung

SIGMA TEK

SIGMA TEK SCP 011 Bedienungsanleitung

SIGMA TEK

SIGMA TEK HMI-Link G2 Device Bedienungsanleitung

SIGMA TEK

SIGMA TEK SAI 041 Bedienungsanleitung

SIGMA TEK

SIGMA TEK NC 100 Bedienungsanleitung

SIGMA TEK

SIGMA TEK HZS 7321 Bedienungsanleitung

SIGMA TEK

SIGMA TEK AI 047 Bedienungsanleitung

SIGMA TEK

SIGMA TEK SR 022 Bedienungsanleitung

SIGMA TEK

SIGMA TEK EZ 101 Bedienungsanleitung

SIGMA TEK

SIGMA TEK TO 161 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung