SIGMA TEK CCP 531 Bedienungsanleitung

C-DIAS PROCESSOR MODULE CCP 531

12.04.2017 Page 1

C-DIAS Processor Module CCP 531

The CCP 531 processor module runs the control program and

thereby represents an essential component of an automation

system. The internal DC/DC converter powers all modules on a

C-DIAS module carrier.

The CAN bus, an Ethernet interface or the USB device (Mini

USB) can be used as the online interface connection.

A 7-segment display and 2 status LEDs provide information on

the actual status of the CPU.

For program updates, the integrated USB Host interface can be

used (USB stick, keyboard). With help from the exchangeable

SD card, the entire control program can be easily exchanged.

The CCP 531 processor module is designed to be mounted in

the control cabinet.

Compatibility

Completely PC-compatible. The CCP 531 works with standard PC BIOS and therefore no

SIGMATEK-specific BIOS is needed; the LASAL operating system in provided.

C-DIAS PROCESSOR MODULE CCP 531

Page 2 12.04.2017

Technical Data

Performance data

Processor

EDGE-Technology X86 compatible

16-bit data bus

Clock frequency

500 MHz

Addressable I/O/P modules

CAN bus: 32

C-DIAS bus: 8

Internal I/O

Internal cache

32-kbyte L1 Cache

256-kbyte L2 Cache

BIOS

AMI

Internal program and data memory

(DDR2 RAM)

64 Mbytes

Internal remnant data memory

512 Kbytes (1)

Internal storage device

512 Mbytes microSD card (12-104-531)

1-Gbyte microSD card (12-104-531-1)

Interface connections

1 x USB Host 2.0 (full speed 12 MBit/s)

1 x USB Device 1.1

1 x Ethernet

1 x CAN

1 x C-DIAS

Data buffer

Yes

Status display

Yes

Status LEDs

Yes

Real-time clock

Yes (buffering approximately 10 days)

(1) See chapter “Note on SRAM Behavior”

C-DIAS PROCESSOR MODULE CCP 531

12.04.2017 Page 3

Electrical requirements

Supply voltage

+18 –30 V DC

Supply voltage (UL)

18 –30 V DC (Class 2)

Current consumption of (+24 V)

power supply

Typically 150 mA

Maximum 500 mA

Current consumption of (+24 V)

power supply (UL)

Maximum 500 mA

Starting current

For a very short time (~20 ms) : 30 A

Power supply on the C-DIAS bus

Supplied by the CCP 531

Current load on C-DIAS bus

(power supply for I/O/P modules).

Maximum 1.2 A

Only US and Canada:

Use class 2 power supply only!

Seulement Etats-Unis et Canada:

Utilisez alimentation de la classe 2 uniquement!

Standard configuration

Ethernet 1

IP: 10.10.150.1

Subnet-Mask: 255.0.0.0

CAN bus

Station: 00

Baudrate: 01 = 500 kBaud

Problems can arise if a control is connected to an IP network, which contains mod-

ules that do not run a SIGMATEK operating system. With such devices, Ethernet

packets could be sent to the control with such a high frequency (i.e. broadcasts),

that the high interrupt load could cause a real-time runtime error or runtime error. By

configuring the packet filter (Firewall or Router) accordingly however, it is possible

to connect a network with SIGMATEK hardware to a third party network without trig-

gering the error mentioned above.

Des problèmes peuvent survenir si un automate est connecté à un réseau IP con-

tenant des modules qui ne fonctionnent pas sous un système d'exploitation

SIGMATEK. Avec de tels dispositifs, les paquets Ethernet peuvent être envoyés à

l’automate avec une fréquence tellement élevée (càd. diffusion), que les interrup-

tions ainsi générées peuvent provoquer une erreur d'exécution. En configurant

d’une façon appropriée le filtre de paquets (pare-feu ou un routeur) il est toutefois

possible de connecter un réseau avec le matériel SIGMATEK à un réseau tiers sans

déclencher l'erreur mentionnée ci-dessus.

C-DIAS PROCESSOR MODULE CCP 531

Page 4 12.04.2017

Miscellaneous

Article number

12-104-531 (512 Mbytes microSD card)

12-104-531-1 (1-Gbyte microSD card)

Hardware version

1.x

Project back-up

Internally on the microSD card

Standard

UL508 (E247993)

Environmental conditions

Storage temperature

-10 ... +85 °C

Operating temperature

0 ... +60 °C

Humidity

10 –90 %, uncondensed

EMV stability

According to EN 61000-6-2 (industrial area)

Shock resistance

EN 60068-2-27

150 m/s²

Protection Type

EN 60529

IP20

Protection Type (UL)

open type device

Pollution degree

C-DIAS PROCESSOR MODULE CCP 531

12.04.2017 Page 5

Mechanical Dimensions

104.10 (dimensioning incl. covers)

24.90

129

109.2

C-DIAS PROCESSOR MODULE CCP 531

Page 6 12.04.2017

Connector Layout

C-DIAS PROCESSOR MODULE CCP 531

12.04.2017 Page 7

X1: USB Device 1.1

n.c. = do not use

X2: USB Host 2.0

It should be noted that many of the USB devices on the market do not comply with

USB specifications; this can lead to device malfunctions. It is also possible that

these devices will not be detected at the USB port or function correctly. Therefore, it

is recommended that every USB stick be tested before actual use.

Il faut souligner que la plupart des périphériques USB sur le marché ne sont pas

conformes aux spécifications USB, ce qui peut entraîner des dysfonctionnements de

l'appareil. Il est également possible que ces dispositifs ne seront pas détectés par le

port USB ou qu’ils ne fonctionnent pas correctement. Par conséquent, il est recom-

mandé que chaque clé USB soit testée avant l'utilisation sur l’automate.

X3: Ethernet

Function

+5 V

D-

D+

n.c.

GND

Function

+5 V

D-

D+

GND

Function

TX+

TX-

RX+

4 - 5

n.c.

RX-

7 - 8

C-DIAS PROCESSOR MODULE CCP 531

Page 8 12.04.2017

X4: CAN-Bus

X5: Power plug

X6: microSD Card

It is recommended that only storage media provided by SIGMATEK

(CompactFlash cards, microSD cards etc.) be used.

Order number for the 512-Mbyte EDGE microSD card: 12-630-051

Order number for the 1-Gbyte EDGE microSD card: 12-630-101

The number of read and write actions have a significant influence on the

lifespan of the storage media.

Il est recommandé de n’utiliser que les supports de stockage approuvés par SIG-

MATEK (compact flash, microSD, etc.).

Numéro de commande pour la carte microSD 512 Mo Edge est le: 12-630-051

Numéro de commande pour la carte microSD 1 Go Edge est le: 12-630-101

Le nombre de cycles de lecture et d'écriture a l’influence notable sur la durée de

vie des supports de stockage.

Function

CAN A (CAN LOW)

CAN B (High)

CAN A (CAN LOW)

CAN B (High)

GND

n.c.

Function

+24 V supply

GND

Function

DAT2

CD/DAT3

CMD

+3V3

Clk

GND

DAT0

DAT1

1 2

C-DIAS PROCESSOR MODULE CCP 531

12.04.2017 Page 9

Exchanging the microSD card

The microSD card is located under the LED cover.

To exchange the microSD card, carefully lift the LED cover.

The microSD card is located on the left side and can be

disengaged by lightly pressing on the card itself.

Remove the microSD card.

C-DIAS PROCESSOR MODULE CCP 531

Page 10 12.04.2017

Connector

Type

Wire Size

Max. drive torque

USB Type Mini-B

USB Type A

RJ 45

B2L 3.5/6

0.13 - 1.0 mm2

28 - 18 AWG (UL/CSA)

Cage Clamp

FK-MCP 1.5/ 2-ST-3.5

0.14 - 1.5 mm2

28 - 16 AWG (UL/cUL)

Cage Clamp

MC 1.5/ 2-ST-3.5

0.13 - 1.0 mm2,

30 - 16 AWG (UL),

28 - 16 AWG (CSA)

0.22 - 0.25 Nm

Applicable connectors

USB Device: 5-pin, type Mini-B

USB Host: 4-pin, type A

Ethernet: 8-pin, RJ45

CAN Bus: 6-pin Weidmüller plug, B2L3,5/6

Supply: 2-pin Phoenix plug with screw terminal technology MC 1.5/ 2-ST-3.5

2-pin Phoenix plug with spring terminal FK-MCP 1.5/ 2-ST-3.5

The complete C-DIAS CKL 017 connector set with spring terminals is available from

Sigmatek under the article number 12-600-017.

Inhaltsverzeichnis

Andere SIGMA TEK Steuereinheit Handbücher

SIGMA TEK

SIGMA TEK ST 151 Bedienungsanleitung

SIGMA TEK

SIGMA TEK MDD 111-2 Bedienungsanleitung

SIGMA TEK

SIGMA TEK MDP 102-1 Bedienungsanleitung

SIGMA TEK

SIGMA TEK C-DIAS Bedienungsanleitung

SIGMA TEK

SIGMA TEK AI 022-1 Bedienungsanleitung

SIGMA TEK

SIGMA TEK PW 022 Bedienungsanleitung

SIGMA TEK

SIGMA TEK STO 081 Bedienungsanleitung

SIGMA TEK

SIGMA TEK PIM 021 Bedienungsanleitung

SIGMA TEK

SIGMA TEK SCP 011 Bedienungsanleitung

SIGMA TEK

SIGMA TEK PL 221 Bedienungsanleitung

SIGMA TEK

SIGMA TEK SCP 111-S Bedienungsanleitung

SIGMA TEK

SIGMA TEK CP 112-1 Bedienungsanleitung

SIGMA TEK

SIGMA TEK STO 081 Bedienungsanleitung

SIGMA TEK

SIGMA TEK SCP 211 Bedienungsanleitung

SIGMA TEK

SIGMA TEK AI 047 Bedienungsanleitung

SIGMA TEK

SIGMA TEK AI 0812 Bedienungsanleitung

SIGMA TEK

SIGMA TEK SCP 111 Bedienungsanleitung

SIGMA TEK

SIGMA TEK DC 061-1 Bedienungsanleitung

SIGMA TEK

SIGMA TEK DIAS-Drive 2000 Bedienungsanleitung

SIGMA TEK

SIGMA TEK S-DIAS EC 121 Bedienungsanleitung

SIGMA TEK

SIGMA TEK HMI-Link G2 Device Bedienungsanleitung

SIGMA TEK

SIGMA TEK VI 021 Bedienungsanleitung

SIGMA TEK

SIGMA TEK HZS 7321 Bedienungsanleitung

SIGMA TEK

SIGMA TEK DC 061-1 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung