SIGMA TEK CP 102 Bedienungsanleitung

CP 102

S-DIAS CPU Module

Instruction Manual

Date of creation: 06.11.2014

Version date: 26.07.2023

Article number: 20-004-102-E

Publisher: SIGMATEK GmbH & Co KG

A-5112 Lamprechtshausen

Tel.: +43/6274/4321

Fax: +43/6274/4321-18

Email: [email protected]

WWW.SIGMATEK-AUTOMATION.COM

SIGMATEK GmbH & Co KG

Translation of the Original Instructions

distributed in any form (print, photocopy, microfilm or in any other process) without the express permission.

We reserve the right to make changes in the content without notice. The SIGMATEK GmbH & Co KG is not

responsible for technical or printing errors in the handbook and assumes no responsibility for damages that occur

through use of this handbook.

S-DIAS CPU MODULE CP 102

26.07.2023 Page 1

S-DIAS CPU Module CP 102

with 1 Ethernet

1 USB-OTG

1 CAN

The S-DIAS CPU module CP 102 is a high-performance processor

unit for the S-DIAS IO modules. With Ethernet, CAN bus and USB

OTG (Host and Device) interfaces, the module can be used for

various applications. A zero-voltage protected RAM area is available,

which is implemented by copying a data block from the DDR RAM to

the NAND Flash.

The voltage supply is already available in the module. The number of

modules that can be supplied depends on the total current

consumption. The CP 102 can supply a maximum of 0.6 A.

S-DIAS has no intelligent master (manager)

CP 102 S-DIAS CPU MODULE 
 
Page 2 26.07.2023 
Contents 
1Introduction............................................................................. 5 
1.1 Target Group/Purpose of this Operating Manual......................5 
1.2 Important Reference Documentation .........................................5 
1.3 Contents of Delivery.....................................................................5 
2Basic Safety Directives .......................................................... 6 
2.1 Symbols Used...............................................................................6 
2.2 Disclaimer......................................................................................8 
2.3 General Safety Directives ............................................................9 
2.4 Software/Training .......................................................................10 
3Standards and Directives......................................................11 
3.1 Directives.....................................................................................11 
3.1.1 EU Conformity Declaration................................................................11 
4Type Plate...............................................................................12 
5Technical Data .......................................................................13 
5.1 Performance Data.......................................................................13 
5.2 Standard Configuration..............................................................14 
5.3 Electrical Requirements.............................................................15 
5.3.1 Module Supply (Input) .......................................................................15 
5.3.2 S-DIAS Bus Supply (Output) .............................................................16 
5.4 Safety-Relevant Parameters......................................................18 
5.5 Miscellaneous .............................................................................18 

 S-DIAS CPU MODULE CP 102 
 
07.2023 Page 3 
6 Environmental Conditions.........................................................19 
6Mechanical Dimensions........................................................20 
7Connector Layout..................................................................21 
1 Status LEDs.................................................................................22 
2 Connectors..................................................................................22 
3 Applicable Connector Cables....................................................23 
4 Applicable Connectors...............................................................24 
5 Label Field...................................................................................25 
8CAN Bus Setup......................................................................26 
1 CAN Bus Station Number ..........................................................26 
2 Number of CAN Bus Participants..............................................26 
3 CAN Bus Data Transfer Rate.....................................................26 
4 CAN Bus Termination.................................................................27 
9Strain Relief ...........................................................................28 
Process Diagram...................................................................29 
Status and Error Messages..................................................30 
Application Exceptions.........................................................37 
1 Data Breakpoint ..........................................................................37 
Wiring Guidelines..................................................................37 
1 Shielding......................................................................................38 

CP 102 S-DIAS CPU MODULE 
 
Page 4 26.07.2023 
2 ESD-Protection ...........................................................................38 
Assembly/Installation............................................................39 
1 Check Contents of Delivery.......................................................39 
2 Mounting......................................................................................40 
Transport/Storage..................................................................42 
Storage ...................................................................................42 
Maintenance...........................................................................43 
1 Service.........................................................................................43 
2 Repair...........................................................................................43 
Disposal..................................................................................43 
 

S-DIAS CPU MODULE CP 102

26.07.2023 Page 5

1 Introduction

1.1 Target Group/Purpose of this Operating Manual

This operating manual contains all information required for the operation of the product.

This operating manual is intended for:

•Project planners

•Technicians

•Commissioning engineers

•Machine operators

•Maintenance/test technicians

General knowledge of automation technology is required.

Further help and training information, as well as the appropriate accessories can be found

on our website www.sigmatek-automation.com.

Our support team is happily available to answer your questions.

Please see our website for our hotline number and business hours.

1.2 Important Reference Documentation

This and additional documents can be downloaded from our website or obtained through

support.

1.3 Contents of Delivery

1x CP 102

CP 102 S-DIAS CPU MODULE

Page 6 26.07.2023

2 Basic Safety Directives

2.1 Symbols Used

The following symbols are used in the operator documentation for warning and danger

messages, as well as informational notes:

DANGER

Danger indicates that death or serious injury will occur, if the

specified measures are not taken.

To avoid death or serious injuries, observe all guidelines.

Danger indique une situation dangereuse qui, faute de prendre les

mesures adéquates, entraînera des blessures graves, voire mortelles.

Respectez toutes les consignes pour éviter des blessures

graves, voire mortelles.

WARNING

Warning indicates that death or serious injury can occur, if the

specified measures are not taken.

To avoid death or serious injuries, observe all guidelines.

Avertissement d’une situation dangereuse qui, faute de prendre les

mesures adéquates, entraînera des blessures graves, voire mortelles.

Respectez toutes les consignes pour éviter des blessures

graves, voire mortelles.

CAUTION

Caution indicates that moderate to slight injury can occur, if the

specified measures are not taken.

To avoid moderate to slight injuries, observe all guidelines.

Attention indique une situation dangereuse qui, faute de prendre les

mesures adéquates, peut entraîner des blessures assez graves ou

légères.

Respectez toutes les consignes pour éviter des blessures

graves, voire mortelles.

S-DIAS CPU MODULE CP 102

26.07.2023 Page 7

INFORMATION

Information

Provides important information on the product, handling or

relevant sections of the documentation, which require

attention.

CP 102 S-DIAS CPU MODULE

Page 8 26.07.2023

2.2 Disclaimer

INFORMATION

The contents of this operating manual were prepared with the greatest

care. However, deviations cannot be ruled out. This operating manual

is regularly checked and required corrections are included in the

subsequent versions. The machine manufacturer is responsible for the

proper assembly, as well as device configuration. The machine

operator is responsible for safe handling, as well as proper operation.

The current operating manual can be found on our website. If

necessary, contact our support.

Subject to technical changes, which improve the performance of the

devices. The following operating manual is purely a product

description. It does not guarantee properties under the warranty.

Please thoroughly read the corresponding documents and this

operating manual before handling a product.

SIGMATEK GmbH & Co KG is not liable for damages caused

through, non-compliance with these instructions or applicable

regulations.

Inhaltsverzeichnis

Andere SIGMA TEK Steuereinheit Handbücher

SIGMA TEK

SIGMA TEK SCP 211 Bedienungsanleitung

SIGMA TEK

SIGMA TEK CP 101 Bedienungsanleitung

SIGMA TEK

SIGMA TEK DIAS-Drive 2000 Bedienungsanleitung

SIGMA TEK

SIGMA TEK AM 441 Bedienungsanleitung

SIGMA TEK

SIGMA TEK S-DIAS PS 101 Bedienungsanleitung

SIGMA TEK

SIGMA TEK ST 011 Bedienungsanleitung

SIGMA TEK

SIGMA TEK S-DIAS EC 121 Bedienungsanleitung

SIGMA TEK

SIGMA TEK SCP 011 Bedienungsanleitung

SIGMA TEK

SIGMA TEK MDD 111-2 Bedienungsanleitung

SIGMA TEK

SIGMA TEK PW 022 Bedienungsanleitung

SIGMA TEK

SIGMA TEK KL 181 Bedienungsanleitung

SIGMA TEK

SIGMA TEK S-DIAS DM 821 Bedienungsanleitung

SIGMA TEK

SIGMA TEK CP 112 Bedienungsanleitung

SIGMA TEK

SIGMA TEK ST 151 Bedienungsanleitung

SIGMA TEK

SIGMA TEK SCP 111-S Bedienungsanleitung

SIGMA TEK

SIGMA TEK AI 0812 Bedienungsanleitung

SIGMA TEK

SIGMA TEK CCP 531 Bedienungsanleitung

SIGMA TEK

SIGMA TEK SR 022 Bedienungsanleitung

SIGMA TEK

SIGMA TEK EZ 102 Bedienungsanleitung

SIGMA TEK

SIGMA TEK S-DIAS AI 022 Bedienungsanleitung

SIGMA TEK

SIGMA TEK AM 222 Bedienungsanleitung

SIGMA TEK

SIGMA TEK PIM 021 Bedienungsanleitung

SIGMA TEK

SIGMA TEK SDM 081 Bedienungsanleitung

SIGMA TEK

SIGMA TEK KL 180 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung