SIGMA TEK ISE 021 Bedienungsanleitung

ISE 021

S-DIAS Interface Module

RS232 / RS485

Operating Manual

Date of creation: 23.04.2014

Version date: 26.07.2023

Article number: 20-101-021-E

Publisher: SIGMATEK GmbH & Co KG

A-5112 Lamprechtshausen

Tel.: +43/6274/4321

Fax: +43/6274/4321-18

Email: [email protected]

WWW.SIGMATEK-AUTOMATION.COM

SIGMATEK GmbH & Co KG

Translation of the Original Instructions

distributed in any form (print, photocopy, microfilm or in any other process) without the express permission.

We reserve the right to make changes in the content without notice. The SIGMATEK GmbH & Co KG is not

responsible for technical or printing errors in the handbook and assumes no responsibility for damages that occur

through use of this handbook.

S-DIAS INTERFACE MODULE ISE 021

26.07.2023 Page 1

S-DIAS Interface Module ISE 021

with 1 RS232 interface with handshake lines

or 2 RS232 interfaces without handshake lines(1)

1 RS485 interface with switchable termination and spread

resistors

The S-DIAS ISE 021 interface module has an RS232 interface with the

handshake signals RTS and CTS. Alternatively to the handshake

signals, these signals can be configured as a second RS232 interface.

In this configuration, two independent RS232 interfaces without

handshake lines are available. Both RS232 interfaces support data

rates up to 115200 Baud.

The ISE 021 also has an RS485 interface with switchable 120 Ω

termination and spread resistors (switchable via software). The RS485

interface is overvoltage-proof up to 15 V and can be operated with data

rates up to 921600 Baud.

The module requires no external +24 V supply.

(1)switchable via software starting with HW version 4.20

ISE 021 S-DIAS INTERFACE MODULE 
 
Page 2 26.07.2023 
Contents 
1Introduction............................................................................. 6 
1.1 Target Group/Purpose of this Operating Manual......................6 
1.2 Important Reference Documentation .........................................6 
1.3 Contents of Delivery.....................................................................6 
2Basic Safety Directives .......................................................... 7 
2.1 Symbols Used...............................................................................7 
2.2 Disclaimer......................................................................................9 
2.3 General Safety Directives ..........................................................10 
2.4 Software/Training .......................................................................11 
3Standards and Directives......................................................12 
3.1 Directives.....................................................................................12 
3.1.1 EU Conformity Declaration................................................................12 
4Type Plate...............................................................................13 
5Technical Data .......................................................................14 
5.1 Performance Data.......................................................................14 
5.2 Electrical Requirements.............................................................15 
5.3 Miscellaneous .............................................................................17 
5.4 Environmental Conditions.........................................................17 
6Mechanical Dimensions........................................................18 
7Connector Layout..................................................................19 

 S-DIAS INTERFACE MODULE ISE 021 
 
07.2023 Page 3 
1 Status LEDs.................................................................................20 
2 Applicable Connectors...............................................................21 
3 Label Field...................................................................................22 
8Wiring.....................................................................................23 
1 Example Connection ..................................................................23 
2 Example Connection (Starting from HW-Version 3.0).............24 
3 RS485 Guidelines........................................................................25 
3.1 General Data / Specifications............................................................ 25 
3.2 Connection to ISE 021 (up to HW-Version 3.0)................................. 25 
3.3 Wiring................................................................................................ 26 
4 RS232 Guidelines........................................................................28 
4.1 General data /specifications.............................................................. 28 
5 Shielding......................................................................................29 
9Assembly/Installation ...........................................................30 
1 Check Contents of Delivery.......................................................30 
2 Mounting......................................................................................31 
Supported Cycle Times ........................................................33 
1 Cycle Times below 1 ms (in µs).................................................33 
2 Cycle Times equal to or higher than 1 ms (in ms)...................33 
Hardware Class ISE021.........................................................34 
1 Interfaces.....................................................................................36 
1.1 General............................................................................................. 36 

ISE 021 S-DIAS INTERFACE MODULE 
 
Page 4 26.07.2023 
1.2 Serial Outputs 1-3..............................................................................36 
1.3 Communication Interfaces.................................................................37 
2 Globale Methods.........................................................................38 
2.1 StartUser ...........................................................................................38 
2.2 StopUser............................................................................................39 
2.3 SerSend ............................................................................................39 
2.4 SerClose............................................................................................39 
2.5 SetOnline...........................................................................................40 
2.6 RecvBlock..........................................................................................40 
2.7 RecvChar...........................................................................................40 
2.8 GetRecvState....................................................................................41 
2.9 GetSendState....................................................................................41 
2.10 GetError.............................................................................................41 
2.11 IsInitialized.........................................................................................41 
2.12 GetInfo...............................................................................................42 
2.13 SetBufferRecv ...................................................................................42 
2.14 ClearRecvBuffer................................................................................42 
2.15 RtsOnOff............................................................................................43 
2.16 rdRts..................................................................................................43 
2.17 rdCts..................................................................................................43 
2.18 DtrOnOff............................................................................................44 
2.19 rdDtr ..................................................................................................44 
2.20 rdDcd.................................................................................................44 
2.21 rdDsr..................................................................................................45 
2.22 rdRI....................................................................................................45 
2.23 SetRSMode.......................................................................................45 

 S-DIAS INTERFACE MODULE ISE 021 
 
07.2023 Page 5 
2.24 GetRSMode...................................................................................... 46 
2.25 RecvTimingBlock.............................................................................. 46 
2.26 RecvTimingChar............................................................................... 46 
2.27 SetTimingBufferRecv........................................................................ 47 
2.28 ClearTimingBuffer............................................................................. 47 
2.29 GetInterfaceType.............................................................................. 47 
2.30 SetBaudrate...................................................................................... 48 
3 Meaning of the ErrorCodes........................................................49 
4 Internal Properties......................................................................50 
4.1 Maximum Transfer Rates.................................................................. 50 
Transport/Storage .................................................................51 
Storage...................................................................................51 
Maintenance...........................................................................52 
1 Service.........................................................................................52 
2 Repair...........................................................................................52 
Disposal .................................................................................52 
 

ISE 021 S-DIAS INTERFACE MODULE

Page 6 26.07.2023

1 Introduction

1.1 Target Group/Purpose of this Operating Manual

This operating manual contains all information required for the operation of the product.

This operating manual is intended for:

•Project planners

•Technicians

•Commissioning engineers

•Machine operators

•Maintenance/test technicians

General knowledge of automation technology is required.

Further help and training information, as well as the appropriate accessories can be found

on our website www.sigmatek-automation.com.

Our support team is happily available to answer your questions.

Please see our website for our hotline number and business hours.

1.2 Important Reference Documentation

This and additional documents can be downloaded from our website or obtained through

support.

1.3 Contents of Delivery

1x ISE 021

S-DIAS INTERFACE MODULE ISE 021

26.07.2023 Page 7

2 Basic Safety Directives

2.1 Symbols Used

The following symbols are used in the operator documentation for warning and danger

messages, as well as informational notes:

DANGER

Danger indicates that death or serious injury will occur, if the

specified measures are not taken.

To avoid death or serious injuries, observe all guidelines.

Danger indique une situation dangereuse qui, faute de prendre les

mesures adéquates, entraînera des blessures graves, voire mortelles.

Respectez toutes les consignes pour éviter des blessures

graves, voire mortelles.

WARNING

Warning indicates that death or serious injury can occur, if the

specified measures are not taken.

To avoid death or serious injuries, observe all guidelines.

Avertissement d’une situation dangereuse qui, faute de prendre les

mesures adéquates, entraînera des blessures graves, voire mortelles.

Respectez toutes les consignes pour éviter des blessures

graves, voire mortelles.

CAUTION

Caution indicates that moderate to slight injury can occur, if the

specified measures are not taken.

To avoid moderate to slight injuries, observe all guidelines.

Attention indique une situation dangereuse qui, faute de prendre les

mesures adéquates, peut entraîner des blessures assez graves ou

légères.

Respectez toutes les consignes pour éviter des blessures

graves, voire mortelles.

ISE 021 S-DIAS INTERFACE MODULE

Page 8 26.07.2023

INFORMATION

Information

Provides important information on the product, handling or

relevant sections of the documentation, which require

attention.

Inhaltsverzeichnis

Andere SIGMA TEK Steuereinheit Handbücher

SIGMA TEK

SIGMA TEK S-DIAS AI 022 Bedienungsanleitung

SIGMA TEK

SIGMA TEK KL 090 Bedienungsanleitung

SIGMA TEK

SIGMA TEK PIM 041-W Bedienungsanleitung

SIGMA TEK

SIGMA TEK DIAS-Drive 2000 Bedienungsanleitung

SIGMA TEK

SIGMA TEK SCP 111 Bedienungsanleitung

SIGMA TEK

SIGMA TEK HMI-Link G2 Device Bedienungsanleitung

SIGMA TEK

SIGMA TEK EZ 101 Bedienungsanleitung

SIGMA TEK

SIGMA TEK AI 047 Bedienungsanleitung

SIGMA TEK

SIGMA TEK NC 100 Bedienungsanleitung

SIGMA TEK

SIGMA TEK MDD 111-2 Bedienungsanleitung

SIGMA TEK

SIGMA TEK SCP 211 Bedienungsanleitung

SIGMA TEK

SIGMA TEK ST 011 Bedienungsanleitung

SIGMA TEK

SIGMA TEK SR 022 Bedienungsanleitung

SIGMA TEK

SIGMA TEK ICA 012 Bedienungsanleitung

SIGMA TEK

SIGMA TEK MDP 102-1 Bedienungsanleitung

SIGMA TEK

SIGMA TEK SCP 011 Bedienungsanleitung

SIGMA TEK

SIGMA TEK SCP 111-2 Bedienungsanleitung

SIGMA TEK

SIGMA TEK C-DIAS Bedienungsanleitung

SIGMA TEK

SIGMA TEK PIM 021 Bedienungsanleitung

SIGMA TEK

SIGMA TEK ST 151 Bedienungsanleitung

SIGMA TEK

SIGMA TEK DC 061-1 Bedienungsanleitung

SIGMA TEK

SIGMA TEK SCP 011 Bedienungsanleitung

SIGMA TEK

SIGMA TEK BL 011 Bedienungsanleitung

SIGMA TEK

SIGMA TEK S-DIAS DM 821 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung